微波辐照下无皂阳离子聚(St-MMA)高分子纳米粒子的制备和表征

讨论了微波辐照下 ,以丙酮 水为分散介质 ,利用阳离子型自由基引发剂偶氮二异丁基脒盐酸盐(AIBA)引发苯乙烯 (St)和甲基丙烯酸甲酯 (MMA)共聚 ,合成出表面带正电荷的P(St MMA)共聚物纳米粒子 ,考察了丙酮用量、单体和引发剂浓度对纳米粒子粒径、粒径分布和乳液稳定性的影响 .结果表明 ,丙酮 水的体积比由 0增加到 1 2 6∶1时 ,粒子的平均水化半径从 12 2 2 1nm降低到 2 4 6 8nm ,粒径分布变宽 ,乳液抗电解质稳定性逐渐增强 ;增加引发剂和共聚单体MMA的浓度 ,粒子的水化半径逐渐减小 ,粒径分散系数增大 .     

微波制备均分散无皂高分子纳米微球

在常任微波辐照下合成了聚甲基丙烯酸甲酯（PMMA）、聚苯乙烯（PSt）均分散纳米粒子·体系中来加表面活性剂．与常法相比，反应时间大为缩短．比较PMMA与PSt的粒子形成速度，前者明显大于后者．这可能与MMA对微波的吸收较强有关．在引发剂浓度一定的条件下，做球的体积与单体的浓度呈线性关系，即粒子数不随单体的浓度而变化．这一规律性说明了微波辐照有利于一次性成核，这也是微波能制备单分散体系的原因所在．     

超声辐照引发MMA微乳液聚合

研究了超声波引发甲基丙烯酸甲酯(MMA)的微乳液聚合.辐照40min时单体转化率高达90%.透射电镜观察发现,PMMA微乳液平均粒径为36.5nm,粒径分布窄,表明超声波引发是制备PMMA微乳液的有效方法.采用分光光度计对微乳液聚合过程中乳胶粒的形成和大小进行了间接表征,研究了超声功率输出、乳化剂、助乳化剂、单体和引发剂对MMA微乳液聚合的影响.     

微波辐照制备无皂阳离子PMMA胶乳粒子

在微波辐照条件下 ,用偶氮二异丁基脒盐酸盐 (AIBA)引发甲基丙烯酸甲酯的均聚 ,制得窄分散的无皂阳离子胶乳粒子 .讨论了引发剂的浓度、单体的浓度、离子强度等对粒子大小、分散性和乳液稳定性的影响 .对微波辐照和水浴加热进行比较 ,发现微波辐照反应速度快、反应无恒速阶段 ,所得粒子的粒径小 ,粒子数目多 ,这为通过改变反应条件制备适宜的窄分散的胶乳粒子提供了一条途径 .     

无皂阳离子MMA/HEMA胶乳粒子的制备及表征

讨论了微波辐照下带正电荷的自由基引发剂偶氮二异丁基脒盐酸盐(AIBA)引发甲基丙烯酸甲酯(MMA)和甲基丙烯酸2-羟乙酯(HEMA)共聚,用透射电子显微镜、红外光谱仪、差热分析仪等对聚合产物进行表征.结果表明: 两种单体发生了共聚反应,制得均分散、表面洁净的无皂阳离子胶乳粒子;粒子的粒径随着单体HEMA浓度的增加先减小后增加.在微波辐照下共聚反应的速率非常快,几乎所有的反应在20 min之内就能完成.随着单体HEMA浓度的增加,乳液抗电解质稳定性提高.     

PMMA纳米粒子的制备及耐温、耐盐性能

以过硫酸钾为引发剂,水和乙醇为反应介质,甲基丙烯酸甲酯(MMA)为单体,通过无皂乳液聚合法制备了聚甲基丙烯酸甲酯(PMMA)纳米粒子,详细考察了反应温度、初始单体含量、分散介质组成对单体转化率的影响规律。透射电子显微镜和傅里叶红外光谱分析结果表明实验制得了单分散的PMMA纳米粒子。纳米粒子在KCl、Mg Cl_2和Al_2(SO_4)_3等溶液中具有良好的耐盐稳分散定性,而且耐高温性能达到150℃,在油气田钻井领域中具有重要的应用前景。     

MMA—St无皂乳液聚合成核机理探讨

讨论了MMA-St无皂乳液聚合,当[KPS]=2.77×10~(-3)mol/L,[MMA]0.51mol/L,[St]=0.49mol/L,70℃反应5.0小时,能得到较高的聚合转化率,较小的胶乳粒径和较大的粒子浓度,并对不同反应时期聚合物的分子量及其分布进行了测定,认为该无皂乳液聚合体系为均相沉淀成核机理。当转化率大于30.9％时,胶乳粒的凝聚程度大于胶乳粒的生成速度。KPS分解产生的自由基起到了稳定乳液的作用。     

高浓度窄分布无皂高分子纳米粒子胶乳的制备

在微波辐照和丙酮存在下,进行了苯乙烯(ST)和甲基丙烯酸甲酯(MMA)的无皂乳液聚合.当丙酮的含量在50％以下时,可以得到稳定的窄分布的纳米粒子胶乳.丙酮的含量由0增加到50％,粒子的平均水化半径由278nm降低到35.4nm.在一定的浓度范围内,固定引发剂过硫酸钾（KPS）的用量,则粒子的平均水化半径与单体的浓度成正比;当单体浓度一定时,随着引发剂浓度的增加,粒子平均水化半径从25nm减少到22nm然后又增大.考虑到引发剂既是粒子表面电荷的来源,又增加了体系的离子强度,在粒子形成过程中,起着稳定和絮凝的双重作用,我们得到了一个简单的公式用以描述粒子的平均水化半径<R     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

丙烯酸-β-羟丙酯存在下无皂白交联型聚苯乙烯胶乳的合成与表征

研究了丙烯酸-β-羟丙酯存在下高浓度苯乙烯的无皂乳液聚合.[St]、[β-HPA]、[KPS]分别为2.66、0.228和5.8×10~(-3)mol/L,80℃反应5h,单体转化率可达90％;经TEM分析,求出了胶乳粒径D=0.23μm,粒子浓度N=3.13×10~(13)粒/cm~3,且胶乳粒径具有单分散性;并讨论了影响乳液稳定性的因素.经IR光谱和溶解性试验证实β-HPA参与了St共聚,推测了自交联机理;求出了聚合反应表观活化能(78.7kJ/mol)和80℃时的聚合反应速率常数(514.3L/mol·s).     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.