微波聚合制备单分散、超细聚甲基丙烯酸甲酯微球

在微波辐照下,通过甲基丙烯酸甲酯(MMA)的无乳化剂乳液聚合,制备出粒径单分散、超细聚甲基丙烯酸甲酯(PMMA)微球。微波显著缩短聚合诱导期,加快聚合反应,其部分原因是微波加快引发剂过硫酸钾(KPS)的分解。实验证明微波辐照下KPS的表观分解活化能(ED)由128.3kJ/mol降低到106.0kJ/mol。单体浓度是影响PMMA乳液粒子尺寸的主要因素,在[MMA]小于0.3mol/L时,平均粒径随单体浓度提高而线形增加;[MMA]为0.3～1.0mol/L时,平均粒径稳定在约200nm;之后随单体浓度进一步增加,乳液稳定性变差。引发剂浓度增加对平均粒径影响较小,但增大引发剂浓度可显著降低粒径分散度。选取[MMA]为0.23～0.3mol/L、[KPS]为3×10-3～6×10-3mol/L可以得到粒径200nm的单分散微球。以丙酮/水(体积比1/3)为反应介质,可制备出数均粒径45nm的PMMA纳米粒子。在体系中加入3.5×10-3mol/L的Cu2+,可制备出数均粒径67nm、单分散的PMMA纳米粒子。     

醇溶性聚丙烯酸酯乳液的合成及性能研究

以丙烯酸乙酯(EA)、甲基丙烯酸甲酯(MMA)和甲基丙烯酸(MAA)为主单体,采用过硫酸盐作引发剂,经预乳化乳液聚合工艺合成了聚丙烯酸酯乳液.讨论了乳化剂种类、单体种类以及功能性单体、引发剂加入工艺对乳液聚合过程及乳液产品性能的影响.结果表明:单体组成为m(MMA)∶m(EA)∶m(MAA)=45∶40∶15所得乳液聚合物能满足使用性能要求;种子引发剂加入质量控制在单体总质量的0.3%,而总的引发剂用量占单体总质量的0.8%较适宜.用差热分析仪和凝胶渗透色谱仪对乳液聚合物进行了表征.     

氟代丙烯酸酯三元共聚物细乳液的合成与表征

在低乳化剂用量和不加助乳化剂的条件下,采用细乳液聚合方法,合成了平均粒径在110～150nm的氟代丙烯酸酯(FA)、甲基丙烯酸甲酯(MMA)及甲基丙烯酸丁酯(BMA)三元共聚物乳液.利用GPC,FTIR及¹HNMR谱表征了共聚物分子量和结构组成,采用激光光散射法研究了聚合过程中粒径变化规律,通过接触角方法对共聚物表面性能进行了表征.结果表明,油溶性引发剂AIBN引发FA-MMA-BMA三元细乳液共聚合的主要成核场所为单体液滴.即每个单体液滴都是一个独立的微型反应器,可避免因为单体水溶性的差异而使共聚组成产生漂移.细乳液聚合合成含氟共聚物乳液的分子量分布窄(1.3～1.5),乳液稳定性能好,共聚物在低含氟量下即表现出优异的疏水疏油性能.     

新型乳液聚合制备疏松PMMA树脂及成粒机理

采用以水相为分散相、甲基丙烯酸甲酯 (MMA) 环己烷混合物为连续相的新型乳液聚合制备PMMA树脂 .发现 ,在未加乳化剂和加入少量Tween2 0乳化剂时 ,均可制备由初级粒子凝聚而成、无明显皮膜结构的疏松PMMA粒子 ,初级粒子粒径小于环己烷存在下MMA悬浮聚合得到的PMMA粒子的初级粒子 .根据聚合体系相构成、PMMA在MMA 环己烷混合液的溶解性及PMMA粒子粒径分布和形态的演变 ,提出了在分散水滴内乳液聚合形成初级粒子 生长 凝聚的新型乳液聚合成粒机理     

微乳液聚合制备聚(甲基丙烯酸丁酯-乙烯基吡咯烷酮)纳米粒子

以BPO和FeSO4为氧化还原引发体系,使用非离子型的乳化剂吐温80,在低乳化剂浓度下(w<0.06)进行甲基丙烯酸丁酯和乙烯基吡咯烷酮的微乳液聚合,制备了粒径窄分布的纳米乳胶粒子。研究了微乳液聚合的引发方式、单体配比和单体加入方式对聚合反应、乳胶粒子粒径及其分布的影响,分析了界面引发微乳液聚合的机制。     

丙烯酸酯纳米乳液的制备与表征

将甲基丙烯酸羟乙酯(HEMA)与甲基丙烯酸(MAA)或丙烯酸(AA)用作甲基丙烯酸甲酯(MMA)／丙烯酸丁酯(BA)乳液聚合体系的反应性助乳化剂，采用一种改进的微乳液聚合方法，合成了高单体／乳化剂比例(大于40：1)的聚丙烯酸酯纳米乳液．讨论了引发剂、乳化剂、助乳化别对乳胶粒大小和胶膜吸水率的影响，并对乳液的流体力学行为，共聚物的拉伸行为及耐水性等进行了研究．     

悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

粒径可控阳离子型聚苯乙烯纳米粒子的制备及表征

在采用阳离子型双子（gemini）表面活性剂作为乳化剂,不使用任何助乳化剂的条件下,通过改进微乳液聚合工艺制备了窄分布粒径可控的阳离子型聚苯乙烯（PS）纳米乳液。 改进微乳液聚合的主要特点是：大部分苯乙烯以预乳液的形式恒速滴入引发聚合的微乳液中,使用具有高乳化性能的gemini表面活性剂作为乳化剂能明显降低乳胶粒粒径。 实验结果表明,少量阳离子单体三甲基烯丙基氯化铵作为共聚单体能够明显减小Z均粒径、降低粒度分布,乳化剂用量、引发剂用量和反应温度均能影响制备乳胶粒的粒径及其粒度分布。 乳化剂和引发剂用量分别为苯乙烯质量的5%~10%和1.0%~1.5%、反应温度为70~75 ℃时,能够制备粒径小分布窄的阳离子型聚苯乙烯纳米粒子。 Z均粒径与苯乙烯质量之间的线性关系表明,Z均粒径可以通过苯乙烯用量来控制。 不同聚合工艺下制备的聚合物粒度分布曲线表明,改进微乳液聚合工艺（半连续预乳化工艺）在制备窄分布的聚合物纳米粒子方面具有很强的优越性。     

超细荧光聚合物纳米微球的制备

合成了具有较高荧光量子产率(0.69)和良好光稳定性的可聚合荧光染料单体,该荧光染料的光稳定性高于商品化的染料罗丹明B。 通过氧化还原引发剂引发乳液聚合制备了超细荧光聚合物纳米微球,将染料分子共价连接在聚合物链上。 使用非离子表面活性剂Triton X-100作为乳化剂、甲基丙烯酸甲酯(MMA)作为单体和助乳化剂,制备的超细纳米微球平均粒径为22 nm,而不加MMA时制备出的纳米微球平均粒径在150 nm左右。 由于微球表面带有苄氯基团,为进一步的微球功能化提供了途径。     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

Microemulsion Polymerization: An Undergraduate Experiment in the Synthesis of Nanosized Polystyrene Particles

The synthesis of polystyrene nanoparticles through microemulsion polymerization is presented as an undergraduate advanced organic laboratory exercise. The resultant polymers molecular weight and particle size are studied as a function of monomer and initiator concentration. A comparison of cationic vs. anionic surfactants, and their effects on the polymer produced through microemulsion polymerization are also investigated. A direct relationship is observed between molecular weight and monomer concentration. A direct relationship is also found for the particle size of the latex produced. An inverse relationship is observed for molecular weight and particle size as the initiator concentration was raised. Comparison of molecular weight and latex size for cationic and anionic surfactants demonstrates that the anionic surfactant produces both a higher molecular weight and a larger latex size over the entire monomer and initiator concentration ranges.     

Microemulsion copolymerization of styrene and acrylonitrile with n‐butanol as the cosurfactant

The microemulsion copolymerization of styrene and acrylonitrile in an n‐butanol/cetyltrimethylammonium bromide/oil/water microemulsion system was studied. The solubilization sites of the two monomers were determined with an NMR technique. The results showed that the solubilization behaviors of the two monomers were quite different. Most of the styrene was solubilized in the palisade layer of the microemulsion, whereas the acrylonitrile had an equilibrium distribution in the aqueous phase and palisade layer of the microemulsion. The reactivity ratios of styrene and acrylonitrile in the microemulsion system were different from those in other media. The effect of the monomer feed composition on the copolymerization kinetics was investigated, and the mechanism of nucleation of the latex particles was examined. The experimental results showed that the copolymerization loci were changed from the microemulsion droplets to the aqueous phase when the concentration of acrylonitrile in the monomer feed reached approximately 80%; this could be further proved by the effect of the monomer feed composition on the copolymerization kinetics. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 203–216, 2005     

TEM研究苯乙烯微乳液聚合机理

用透射电镜(TEM)对苯乙烯(St)/十二烷基硫酸钠(SDS)/正戊醇/水的O/W微乳液体系在反应前、聚合过程中和反应结束后等不同时间里进行观察,并测定苯乙烯微乳液聚合前后粒径的大小,根据粒径大小的变化研究苯乙烯微乳液聚合成核机理,发现其成核位置主要是在胶束和单体微珠滴里。此外,还发现SDS/St的质量比越大,相对分子质量越低。     

室温交联型硅丙微胶乳的合成研究Ⅲ.聚合工艺对聚合稳定性及胶膜性能的影响

采用两种聚合工艺(种子微乳液聚合法和单体预乳化法)分别合成了室温交联型有机硅改性丙烯酸酯聚合物微胶乳，研完了不同工艺条件对聚合稳定性、乳胶粒径和胶膜的结构性能的影响．     

室温交联型硅丙微胶乳的合成研究II.改性微胶乳的粒径控制及其微观形态表征

采用种子微乳液聚合法和单体预乳化法分别合成了室温交联型有机硅改性聚丙烯酸酯微胶乳,研究了硅烷单体的添加和氨化反应对改性微胶乳粒子大小及分布的影响。结果表明:采用种子微乳液聚合法得到的硅丙微胶乳粒子大小与硅烷单体的种类、用量和添加顺序无关,平均粒径约为40~60nm。TEM照片显示出,采用种子微乳液聚合法合成的硅丙微胶乳粒子由于内部存在交联结构而导致表面形状不规则,有“乳突”现象;而采用预乳化法合成的硅丙微胶乳粒径粗大,呈规则的球形,氨化后粒径从100nm以上减小到80nm左右,粒子表面出现“绒毛”现象,这是由于硅烷组分的水解反应受到抑制而使粒子内部的交联密度降低的缘故。     

Ultrasonically induced microemulsion polymerization of styrene

In this paper, ultrasonically induced microemulsion polymerization of styrene was successfully performed, possessing many merits such as high polymerization rate, the formation of small latex particles with a narrow size distribution, the absence of initiator and relatively low surfactant concentration. The monomer conversion reached 70% in 1 h, and the average diameter of polystyrene (PS) latex was about 30 nm which could be prepared with 3% surfactant (sodium dodecyl sulfate, SDS) concentration. The molecular weight of PS was around 10⁶ and the poly-distribution index was 1.06, indicating a very narrow distribution. Several influencing factors were investigated in detail, showing that ultrasonically induced microemulsion polymerization is a new route to prepare PS nanoparticles.     

Polymerization of oil (styrene and methylmethacrylate)-in-water microemulsions

 The polymerization of styrene-in-water and methylmeth-acrylate-in-water microemulsions stabilized by nonionic surfactants was investigated using different initiation techniques. Thermally induced initiation was carried out using potassium persulfate (water soluble) and azobisiso-butyronitrile (AIBN) (oil soluble) at 60° and 50°C, respectively. When the monomer concentration was kept below a certain limit, the particle size of the nanolatex was similar to the droplet size of the microemulsion precursor. At higher monomer concentrations, the latex produced was significantly larger than the microemulsion droplets, as a result of the possible coalescence of the microemulsion droplets during polymerization. By using chemically induced polymerization (hydrogen peroxide+ascorbic acid) at temperatures below the cloud point temperature of the microemulsion or by photochemically induced initiation at room temperature, it was possible to obtain nanolatex particles with similar size to the droplets up to 10% monomer content. In all cases, the particle size was determined using photon correlation spectroscopy (PCS). Electron micrographs of the microlatex particles were taken and these confirmed the measurements obtained by PCS. The molecular weight of the polymers produced was determined by gel permeation chromatography. The average number of polymer molecules per particle was calculated. It was shown in some cases that the nanolatex contained one polymer chain per particle. A mechanism was suggested for polymerization and particle growth. Received: 29 May 1997 Accepted: 28 May 1998     

光散射法研究丙烯酸十八酯和苯乙烯微乳液 共聚机理

在十六烷基溴化吡啶/叔丁醇/15%丙烯酸十八酯和苯乙烯/水体系的O/W微乳液中,使用动态光散射法,研究其中两种单体共聚反应的成核机理。结果表明,聚合过程中乳胶粒成核位置主要在增溶胶囊的单体微珠中,乳胶粒主要依靠单体微珠不断提供单体而长大。     

Modified structural model for predicting particle size in the microemulsion and emulsion polymerization of styrene under microwave irradiation

In this study, the microemulsion and emulsion polymerization of styrene at 70 degrees C in the presence of sodium dodecyl sulfate (SDS, surfactant) and potassium persulfate (KPS, initiator) was conducted under microwave radiation. Laser light scattering was used to characterize the resultant polystyrene latex particles formed at different polymerization stages. The influence of the initial emulsion composition, that is, the SDS, KPS, and styrene concentrations, on the final particle size led us to a simple modified structural model in which we considered the stabilization effects of both the surfactant and the ionic end groups generated from the initiator. This model extended the application of the previous Wu plot from microemulsion polymerization to emulsion polymerization. Using this model, we were not only able to control the particle size but were also able to predict the monomer concentration dependence of the number of the resultant latex particles and the effect of diluting the reaction mixture on the resultant particle size.