氧缺位铁酸盐的制备及结构与还原行为的研究

在３５８Ｋ下用２００ｍｌ／ｍｉｎ的空气氧化碱性悬浮液合成了ＭＦｅ_２Ｏ_（４＋δ）（δ≥０，Ｍ＝Ｆｅ、Ｃｏ、Ｎｉ、Ｍｎ），并在５７３Ｋ下用４０ｍｌ／ｍｉｎ的Ｈ_２还原ＭＦｅ_２Ｏ_（４＋δ）制备了氧缺位铁酸盐ＭＦｅ_２Ｏ_（４－δ）（δ＞０）。用ＸＲＤ、Ｍｓｓｂａｕｅｒ谱等测试方法对铁酸盐的结构进行了表征，考察了铁酸盐的组成及第二金属组分（Ｃｏ、Ｎｉ、Ｍｎ）对铁酸盐还原性能的影响。在Ｈ_２还原３ｈ内，铁酸盐氧缺位程度随还原时间增加而增大，晶格常数也相应增大；５ｈ以上，铁酸盐将被还原为ＭＯ－ＦｅＯ或α－Ｆｅ，晶格常数几乎不变。按Ｆｅ、Ｃｏ、Ｎｉ、Ｍｎ顺序，ＭＯ与ＦｅＯ的相互作用能力、ＭＯ－ＦｅＯ固溶体的稳定性及铁酸盐还原为ＭＯ－ＦｅＯ的能力均增强，ＭＯ－ＦｅＯ进一步还原为α－Ｆｅ的能力却减弱。     

α-Fe_2O_3在LiOH水溶液中的锂化行为

用循环伏安和红外光谱法对α－Ｆｅ_２Ｏ_３在室温ＬｉＯＨ溶液中的锂化行为进行研究．采用Ｘ射线衍射（ＸＲＤ）、电感偶合等离子体光源的原子发射光谱（ＩＣＰ）对α－Ｆｅ_２Ｏ_３电极在第一、二次循环中不同时段进行了跟踪分析测量．实验结果揭示： α－Ｆｅ_２Ｏ_３能进行少量锂化;大量的α－Ｆｅ_２Ｏ_３在第一次放电和充电后反应生成Ｆｅ_３Ｏ_４;之后,Ｆｅ_３Ｏ_４的锂化行为不可避免地为Ｆｅ的析出、氧化反应所限制,但在用ＫＯＨ作电解质溶液的对比实验时发现：α－Ｆｅ_２Ｏ_３在ＬｉＯＨ溶液中的充放电行为与它在ＫＯＨ溶液中是不同的,主要表现为,１）在ＬｉＯＨ溶液中,锂化和Ｆｅ析出、氧化反应协调的结果是其充放电曲线平台高度比在同碱度 ＫＯＨ溶液中降低了 １００ ｍＶ左右, ２）与 Ｋ~（＋）对比, Ｌｉ~（＋）的插入反应促进了α－Ｆｅ_２Ｏ_３到Ｆｅ_３Ｏ_４的转化．     

多乙苯脱氢制多乙烯苯氧化铁催化剂的研究助剂钾,铈对催化性能的影响

研制了适合多乙苯脱氢制多乙烯苯的Ｆｅ－Ｋ－Ｃｅ复合型脱氢催化剂．助剂钾以钾霞石（ＫＡｌＳｉＯ４）方式引入，既克服了钾的大量流失，又保留了钾碱的抗积炭性能，使催化剂活性稳定．另一助剂ＣｅＯ２的加入对催化剂中的各组分起到了一定的分散作用，使催化剂晶粒度变小，并且提高了活性组分Ｆｅ２Ｏ３的还原温度，因而可增强催化剂的抗还原能力．     

Fe/ZrO2催化剂的Mossbauer谱及XAFS表征

考察了经不同温度还原的Ｆｅ／ＺｒＯ２催化剂在ＣＯ２加氢制低碳烃反应中的催化活性,最佳结果为ＣＯ２转化率２７．０％,对Ｃ２＋烃的选择性５６．７％,采用ＸＲＤ,＾５７ＦｅＭｏｓｓｂａｕｅｒ谱,Ｆｅ－Ｋ－吸收边的Ｘ射线吸收近边结构（ＸＡＮＥＳ）及扩展Ｘ射线吸收精细结构（ＥＸＡＦＳ）等表征方法研究了催化剂的表面结构。结果表明,在ＺｒＯ２表面上主要存在α－Ｆｅ及配位不饱和的Ｆｅ＾３＋两种物种。催化剂表面明显呈氧缺位,零价铁相对富集的状态,还原温度对表面结构有显著的影响,最佳还原温度与表面Ｆｅ－Ｏ键的键长有关,结合这种催化剂在ＣＯ２加氢制低碳烃反应中的催化活性,认为α－Ｆｅ与配位不饱和的Ｆｅ＾３＋物种的协同作用是其具有较高催化活性的重要原因。     

多乙苯脱氢制多乙烯苯氧化铁催化剂的研究:助剂钾，铈对催化性能的影响

研制了适合多乙苯脱氢制多乙烯苯的Ｆｅ－Ｋ－Ｃｅ复合型氢催化剂，助剂钾以外霞石（ＫＡｌＳｉＯ４）方式引入，既克服了钾的大量流失，又保留了钾的抗积炭性能，使催化剂活性稳定，另一助剂ＣｅＯ２的加入对催化剂中的各组分起到了一定的分散作用，使催化剂晶粒度变小，并且提高了活性组分Ｆｅ２Ｏ３的还原温度，因而可增强催化剂的抗还原能力。     

氧化铁在ZnO上分散的结构状态及其表征

采用（ＮＨ_４）_３［Ｆｅ（Ｃ_２Ｏ_４）_３］·ｘＨ_２Ｏ的水溶液含浸，Ｆｅ（ＮＯ_３）_３．９Ｈ_２Ｏ水溶液饱和浸渍（含浸）以及Ｆｅ（ＡｃＡｃ）_３的甲苯溶液热吸附三种方法制备了在ＺｎＯ上分散的氧化铁体系。用多种物理化学手段对用不同方法制备的分散体系进行了细致的表征，氧化铁在ＺｎＯ上形成单层分散是困难的。Ｆｅ~（３＋）一般进入到ＺｎＯ载体的表层，结构环境类似于ＺｎＦｅ_２Ｏ_４微晶中的Ｆｅ~（３＋），分散的Ｆｅ~（３＋）通常处于高自旋态，配位对称性并不是正交畸变。在ＺｎＯ上形成尖晶石的趋势最强。在亚单层铁含量范围内，通常形成表面ＺｎｘＦｅ_ｙＯ_ｚ。当铁含量超过单层阈值时，既生成ＺｎＦｅ_２Ｏ_４簇也有ＦｅＯ_ｘ簇存在。无论是ＦｅＯ_ｘ或ＺｎＦｅ_２Ｏ４簇还是表面的Ｚｎ_ｘＦｅ_ｙＯｚ，其Ｆｅ_（３＋）在实验温度范围内，很难被还原为零价铁，ＦｅＯ_ｘ较之Ｚｎ_ｘＦｅ_ｙＯ_ｚ物种难以还原且比体相ａ－Ｆｅ_２Ｏ_３中Ｆｅ~（３＋）要难还原得多。由热吸附法制得的ＦｅＯ_ｘ和ＺｎＦｅ_２Ｏ_４簇具有很低的催化活性，而由含浸法制得的表面Ｚｎ_ｘＦｅ_ｙＯｚ的反应性能有明显的改善。ＺｎＯ载体上不同含铁物种的反应性由Ｆｅ~（３＋）的还原性及是否存在活泼     

环状配合物Me_2Si［η~5－C_5H_4Fe（CO）_2］_2SnR_2的合

通过ＳｎＣｌ_２对化合物Ｍｅ_２Ｓｉ［η~５－Ｃ_５Ｈ_４Ｆｅ（ＣＯ）］_２（μ－ＣＯ）_２（Ⅰ）中Ｆｅ－Ｆｅ键的插入反应以及Ⅰ被Ｎａ－Ｈｇ齐还原所生成的相应双铁负离子｛Ｍｅ_２Ｓｉ［η~５－Ｃ_５Ｈ_４Ｆｅ（ＣＯ）_２］_２｝~（２－）与ＳｎＲ_２Ｃｌ_２（Ｒ＝Ｍｅ，Ｐｈ）的亲核反应，合成了环状化合物Ｍｅ_２Ｓｉ［η~５－Ｃ_５Ｈ_４Ｆｅ（ＣＯ）_２］_２ＳｎＲ_２［Ｒ＝Ｃｌ（１），Ｍｅ（２），Ｐｈ（３）］。以元素分析、ＩＲ和~１ＨＮＭＲ谱表征了它们的结构，并用Ｘ射线衍射测定了配合物３的晶体结构。３为单斜晶系，空间群Ｐ２_１／ｎ，ａ＝１．０３８４（３）ｎｍ，ｂ＝１．６３８４（１）ｎｍ，ｃ＝１．５７６２（５）ｎｍ，β＝９７．９３（２）°，Ｖ＝２．６５６（２）ｎｍ~３，Ｚ＝４，Ｄｘ＝１．７１ｇ／ｍＬ。     

稀土氧化物对Ni／α—Al2O3催化甲烷部分氧化制合成气反应的影响

研究了稀土金属氧化物（Ｌａ２Ｏ３，ＣｅＯ２，Ｐｒ６Ｏ１１和Ｎｄ２Ｏ３）对Ｎｉ／α－Ａｌ２Ｏ３催化剂上甲烷部分氧化制合成气反应的影响．Ｘ光粉末衍射和活性考察结果表明，稀土氧化物使Ｎｉ／α－Ａｌ２Ｏ３催化剂的稳定性有显著提高．稀土氧化物与活性组份Ｎｉ之间的相互作用抑制了催化剂表面Ｎｉ晶粒的生长和迁移，由于这种作用也抑制了催化剂表面积炭的生成．在实验中还发现ＣｅＯ２容易进行Ｃｅ３＋Ｃｅ４＋氧化还原反应而对反应具有催化活性．     

Mo－Fe／SiO_2催化剂中钼流失动力学和流失机理的研究

作为甲醇氧化制甲醛、甲醇氨氧化制ＨＣＮ反应的催化剂，其活性组分钼的流失是导致催化剂失活的主要原因。本文结合程序升温脱附（ＴＰＤ）及Ｘ－光衍射（ＸＲＤ）等测试手段，对Ｍｏ－Ｆｅ／ＳｉＯ_２催化剂及工业实际用多元复合钼催化剂中钼的流失动力学和机理进行了研究。在ＨＣＮ合成过程中，水能引起活性组分钼的流失，而水又是反应产物。对工业用多元复合钼催化剂的流失情况进行了动力学考察，实验发现，催化剂中的钼是较难流失的，ＸＲＤ测试结果表明，Ｍｏ－Ｆｅ／ＳｉＯ_２催化剂中的钼是以Ｆｅ_２（ＭｏＯ_４）_３晶体形式存在的，而反应后催化剂中Ｍｏ为ＭｏＯ_３晶体状态。与其它催化剂比较，ＭｏＯ_３／ＳｉＯ_２催化剂中的钼难流失，而较Ｂｉ－Ｍｏ／ＳｉＯ_２催化剂中的钼易流失。其中工业用催化剂是最为稳定的。根据实验结果，结合我们以前的工作，证明Ｍｏ－Ｆｅ／ＳｉＯ_２催化剂中，由于钼组分和铁组分的相互作用，使得Ｍｏ－Ｆｅ／ＳｉＯ_２中的Ｍｏ的流失难于单组分的ＭｏＯ_３／ＳｉＯ_２催化剂，此外钼流失过程中ＭｏＯ_２（ＯＨ）_２与催化剂中铁组分反应生成钼酸盐的倾向也是Ｍｏ难于流失的原因之一。而Ｍｏ－Ｆｅ／ＳｉＯ_２和Ｍｏ－Ｂｉ／ＳｉＯ_２催化剂中钼流失速度的差异     

助催化剂对Fe1-xO基氨合成催化剂还原性能的影响

当助催化剂存在是地，Ｆｅ１－ｘＯ基催化剂的还原性能明显优于Ｆｅ３Ｏ４基催化剂，其原因是铝、钾、钙的氧化物对催化剂母体相Ｆｅ１－ｘＯ和Ｆｅ３Ｏ４还原性能的影响不同。由于Ａｌ＾３＋大量地进入Ｆｅ３Ｏ４的晶格而强烈地阻止Ｆｅ３Ｏ４的还原，只有少量的Ａｌ＾３＋能进入Ｆｅ１－ｘＯ晶格，因此对Ｆｅ１－ｘＯ的还原影响很小；     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.