双金属在掺硼金刚石表面电化学共沉积-共溶出模型

采用微分脉冲阳极溶出伏安法, 研究了Ag+、Cu2+、Pb2+、Sn2+、Cd2+等多种共存金属离子在掺硼金刚石(BDD)表面双金属共沉积-共溶出电化学行为. 结果表明, 双金属在掺硼金刚石膜表面的共沉积-共溶出模型是由金属本身的析出电位, 金属之间的相互作用, 金属离子和溶液间的相互作用等多种因素决定的. 微分阳极溶出法的研究结果表明, 双金属在掺硼金刚石电极上的共沉积-共溶出过程表现出金属1溶出-金属2溶出、金属1溶出-析氢-金属2溶出、金属1溶出-金属合金溶出-金属2溶出、金属1溶出-析氢-金属2络合物形成-金属2溶出等四种模型.     

石墨烯/铋复合膜修饰玻碳电极检测板蓝根中的铅和镉

采用滴涂法制备石墨烯(GR)修饰的玻碳电极(GCE),通过电化学富集Bi沉积在GR表面,得到GR/Bi-GCE修饰电极.用方波溶出伏安法研究了Cd2+和Pb2+在GR/Bi-GCE上的电化学行为.在0.1 mol/LpH 4.5的醋酸缓冲溶液中,在-1.1 V富集0.5 mg/L Bi(NO3)3溶液210 s后,溶出峰电流与Cd2+和Pb2+的浓度在0.01～85.0 μmol/L范围内呈良好的线性关系,检出限均为0.003 μmol/L.实验结果表明,此修饰电极对Cd2+和Pb2+均有较好的电化学活性,可对两种物质实现同时测定,具有较高的灵敏度和稳定性.将此电极用于板蓝根中Cd2+和Pb2+的含量测定,结果令人满意.     

以镍铬合金为基体的铋膜电极的构建及其应用

采用循环伏安法以镍铬合金为基体构建了铋膜/镍铬合金电极,以扫描电镜表征其表面形貌,利用线性扫描伏安法研究了Pb(II)、Cd(II)在该电极上电化学行为。结果表明:在0.20 mol/L HAc-NaAc缓冲溶液(pH4.5)中,该电极对Pb(II)、Cd(II)离子有较好的电催化活性,Pb(II)、Cd(II)的阳极溶出峰电流与其浓度分别呈良好的线性关系,检出限分别为6.39μg/L和3.52μg/L。     

新型固体汞电极在仪器分析实验中的应用

介绍了仪器分析实验中阳极溶出伏安法的改进方法。利用银汞固体电极阳极溶出伏安法连续测定痕量铜、铅、镉、锌。在pH=4.7的HAc-NH4Ac缓冲液中,富集电位为-1.3V,Cu2 、Pb2 、Cd2 、Zn2 在固体汞电极表面分别还原成金属,并沉积在工作电极上。溶出时电极上沉积的金属分别于-0.13、-0.45、-0.63和-1.00V产生4个灵敏的溶出峰,灵敏度与传统的液态汞电极相当。避免了汞电极使用中的不方便性和毒性。用于大学生实验可得到较好的实验效果。     

电化学活化玻碳/铋膜电极制备及铅、镉离子敏感分析法

以电化学活化玻碳为基底电极原位制备金属铋膜电极,用之于分析Pb2+、Cd2+.方法如下:在氢氧化钠溶液中,由恒电位或循环扫描电位方法活化玻碳电极,随后以稀盐酸替代传统的醋酸缓冲液作为分析溶液将Bi3+与Pb2+、Cd2+共沉积在活化玻碳电极表面,再以方波阳极溶出分析法(SWASV)检测金属离子.结果表明:经简单的电化学清洗步骤即可高重现地再生电极表面,大幅度提高检测Pb2+、Cd2+的灵敏度,检测范围也可拓展至高卤素离子含量的样品.     

痕量Pb2 在nano-TiO2膜电极上的电化学行为及应用研究

利用纳米二氧化钛(nano-TiO2)的结构特性制备了一种nano-TiO2膜修饰的玻碳电极.采用阳极溶出伏安法详细研究了Pb2 在nano-TiO2膜修饰玻碳电极上的电化学响应行为,并对各种实验参数进行了优化.实验结果表明,在0.10 mol/L HAc-NaAc缓冲体系(pH 4.0)中,于-1.2 V富集搅拌480 s,再静置60 s后阳极化扫描,Pb2 在-0.48 V左右出现一灵敏的阳极溶出峰.Pb2 的溶出峰电流与其浓度在2.0×10-9 ～1.0×10-7 mol/L范围内呈良好的线性关系,检出限可达1.0×10-10 mol/L.该修饰电极具有一定的抗干扰能力,将其应用于实际水样中Pb2 的检测,结果令人满意.     

金-钯双金属纳米颗粒修饰玻碳电极阳极溶出伏安法测定三价砷的方法研究

研究了金-钯双金属纳米颗粒修饰电极测定痕量砷的阳极溶出伏安法。采用紫外可见分光光度法、高分辨透射电镜及循环伏安法对颗粒的结构和电化学特性进行表征。采用方波伏安法测定三价砷,探讨了富集电位和方波伏安参数如频率、增幅、波幅以及干扰离子等对测定结果的影响。实验结果表明:金-钯双金属纳米颗粒呈壳-核结构;砷在0.30 V出现灵敏的阳极溶出伏安峰,峰电流与砷质量浓度在0.5～20μg/L范围内呈良好的线性关系,检出限为0.15μg/L;所制备的修饰电极重现性好,可用于三价砷的重复测定。共存离子Cu(Ⅱ)会影响三价砷的测定,而Pb(Ⅱ)、Cd(Ⅱ)、Zn(Ⅱ)等离子的存在对测定结果无影响。     

基于脱氢枞胺基希夫碱-多壁碳纳米管修饰电极测定铅

采用脱氢枞胺基希夫碱和多壁碳纳米管复合材料修饰玻碳电极,以循环伏安法和示差脉冲阳极溶出伏安法研究此修饰电极的导电性能,及Pb2+在此电极上的电化学行为。结果表明,修饰电极在0.2 mol/L HAc-NaAc缓冲体系(pH 5.5)中,于!1.1 V下沉积250 s,Pb2+在1.0×10!8~1.0×10!6mol/L范围内与溶出峰电流呈良好的线性关系,线性回归方程为I(μA)=6.6173C(μmol/L)+0.2597(R=0.9971),检出限为5.0×10!9mol/L(S/N=3)。将此修饰电极用于水样品中Pb2+检测,结果令人满意。本方法操作简便,耗时短,具有很好的准确性、灵敏度和选择性,实现了水样中低浓度铅的准确、快速测定。     

多壁碳纳米管修饰玻碳电极检测铅离子的研究

采用阳极溶出伏安法研究了Pb2+在多壁碳纳米管(MWCNTs)修饰玻碳(GC)电极上的电化学特性,并探讨了溶液pH、MWCNTs修饰层数、富集时间、富集电位与干扰离子等因素的影响。实验表明,Pb2+的线性扫描峰电流与其浓度在0.8~50μmol/L范围内呈现非常好的线性关系,检测限为0.68μmol/L。该电极具有良好的稳定性、重现性和抗干扰能力,并可用于实际水样中Pb2+的检测。     

铕离子掺杂类普鲁士蓝复合汞膜电极的制备及溶出分析特性

在铕离子掺杂类普鲁士蓝(Eu-PB)修饰的玻碳电极表面电沉积汞膜,制备了一种新型化学修饰复合汞膜电极GC/Eu-PB/MFE.研究了修饰层厚度、镀汞方式和汞膜成长过程对复合汞膜形成的影响.以Pb2+和Zn2+为探针离子,对复合汞膜电极和常规玻碳汞膜电极的氢过电位值、表面活性物质的影响、汞膜稳定性和金属离子的溶出伏安行为等进行了对比研究.同时,应用该电极结合示差脉冲阳极溶出伏安法对环境水样中的痕量Pb2+进行了测定.结果表明,Pb2+在该复合汞膜电极上的阳极溶出峰电流与其质量浓度在0.8 ～250 μg/L范围有良好的线性关系(r=0.999 5,n=12),检出限为0.2 μg/L,加标回收率为98% ～102%.用该法对国家铅标准物质溶液对比测定,数据的重复性和准确性均令人满意.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.