以固体超强酸SO4^2-／ZrO2-Fe2O3催化合成醋酸异戊酯

以合成醋酸异戊酯为探针反应,筛选出制备固体超强酸SO2-4 /ZrO2- Fe2O3 (SZF -1 )的最佳工艺条件为:ZrOCl2·8H2O9. 7g, FeCl3·6H2O16. 2g, 常温陈化24h, 0. 5mol·L-1 H2SO4 (15mL·g-1 )浸泡5h, 550℃焙烧3h。以SZF 1为催化剂合成醋酸异戊酯的反应条件为:异戊醇200mmol, n(异戊醇)∶n(醋酸) =1. 0∶1. 3, SZF -1 1g(反应物总质量的3% ), 环己烷15mL, 回流反应3h, 酯化率93. 47%。催化剂连续使用6次后酯化率仍在70%以上。     

NaHSO4·H2O催化合成苯甲酸甲酯

以 Na HSO4 · H2 O催化苯甲酸与甲醇的酯化反应 ,合成了苯甲酸甲酯。研究结果表明 ,Na HSO4 · H2 O具有较高的催化活性。考察了苯甲酸 /甲醇摩尔比、催化剂用量及反应时间对酯产率的影响。在优化反应条件 [n(苯甲酸 )∶n(甲醇 )∶n( Na HSO4 ·H2 O) =1∶ 2∶ 0 .2 9,回流8h]下 ,苯甲酸甲酯产率达 85.3 %。     

以固体超强酸SO2-4/ZrO2-Fe2O3催化合成醋酸异戊酯

以合成醋酸异戊酯为探针反应,筛选出制备固体超强酸SO2-4/ZrO2-Fe2O3(SZF-1)的最佳工艺条件为ZrOCl2·8H2O 9.7 g, FeCl3·6H2O 16.2 g, 常温陈化24 h, 0.5 mol·L-1 H2SO4(15 mL·g-1)浸泡5 h, 550 ℃焙烧3 h.以SZF-1为催化剂合成醋酸异戊酯的反应条件为异戊醇200 mmol, n(异戊醇)n(醋酸)＝1.0 1.3, SZF-1 1 g(反应物总质量的3%), 环己烷15 mL, 回流反应3 h, 酯化率93.47%.催化剂连续使用6次后酯化率仍在70%以上.     

氯化锡催化合成马来酸二丁酯

以SnCl4·5H2 O为催化剂 ,由马来酸酐和正丁醇合成了马来酸二正丁酯。n(马来酸酐 )∶n(正丁醇 )∶n(SnCl4·5H2 O) =1∶4∶0 .0 86 ,回流分水 6 0min ,酯收率达 92 .1% ,并用类似方法合成了收率较高的马来酸二异丁酯、马来酸二正戊酯和马来酸二异戊酯     

SnCl4·5H2 O/C催化合成谷氨酸月桂酯

以谷氨酸和月桂醇为原料,固体酸SnCl4·H2O/C为催化剂合成了谷氨酸月桂酯.正交实验得出最佳的反应条件为月桂醇100 mmol, n(谷氨酸) ∶ n(月桂醇)＝1 ∶ 1, SnCl4·H2O/C 1.2 g, 135 ℃反应4.0 h,醇转化率97.9%.     

固体超强酸ZrO_2/S2O_8~(2-)催化合成肉桂酸甲酯

研究了在固体超强酸ZrO2/S2O2-8催化下,肉桂酸与甲醇作用合成肉桂酸甲酯的工艺.考查了催化剂的用量、酸醇摩尔比、反应时间及催化剂的性能对反应的影响.最佳反应条件为∶n(肉桂酸)∶n(甲醇)=1∶10,m(肉桂酸)∶m(催化剂)=3∶1,反应温度90～95℃,反应时间5h,酯化率为95.7%.     

乳酸丁酯的非均相催化合成

在Ga2 O3负载量为20％,500℃焙烧2h的条件下制备了固体酸催化剂Ga2 O3/SiO2,利用红外光谱分析对催化剂进行了表征.将其用于非均相催化合成乳酸丁酯的反应,考察了催化剂用量、n(正丁醇)∶n(乳酸)、环己烷用量、反应时间和催化剂重复使用性能等因素对酯化率的影响.结果表明,该催化剂催化合成乳酸丁酯的适宜反应...     

NaHSO4·H2O催化合成苯甲酸甲酯

以NaHSO4*H2O催化苯甲酸与甲醇的酯化反应,合成了苯甲酸甲酯.研究结果表明,NaHSO4*H2O具有较高的催化活性.考察了苯甲酸/甲醇摩尔比、催化剂用量及反应时间对酯产率的影响.在优化反应条件[n(苯甲酸)∶n(甲醇)∶n(NaHSO4*H2O)=1∶2∶0.29,回流8h]下,苯甲酸甲酯产率达85.3%.     

磷酸钛固载磷钨酸非均相催化合成异戊酸己酯

通过在300℃下焙烧2h制备了磷酸钛固载15%磷钨酸H3PW12O40(简记为HPW)非均相酯化催化剂HPW/Ti3(PO4)4;采用红外光谱仪分析了催化剂的结构;基于异戊酸与正己醇的酯化反应考察了催化剂用量、n(正己醇)∶n(异戊酸)、反应时间、带水剂种类和催化剂重复使用性能等因素对酯化率的影响.结果表明,该催化剂催化合成异戊酸己酯的适宜反应条件为:0.2mol异戊酸,催化剂用量0.6g,n(正己醇)∶n(异戊酸)=1.6∶1,反应时间4.5h,环己烷10mL;相应的酯化率达95.1%.与此同时,该催化剂循环利用6次后酯化率不低于84%.     

稀土固体超强酸SO_4~(2-)/TiO_2/Ce(Ⅳ)催化合成乙酸正丁酯

以SO2 -4/TiO2 /Ce(Ⅳ )为催化剂 ,乙酸和正丁醇为原料合成了乙酸正丁酯 ,在n(醇 )∶n(酸 ) =1.4 ,催化剂0 .5g(乙酸 2 0 0mmol时 ) ,反应时间 1.5h的优化反应条件下 ,酯化率在 96 %以上。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.