高热稳定性介孔氧化锆的合成及表征

利用阴离子表面活性剂作模板,通过水热均匀沉淀方法成功合成了具有高热稳定性的介孔氧化锆.该方法以十二烷基苯磺酸钠(SDBS)作为介孔结构的导向剂,其含S基团在煅烧时起到了稳定剂的作用.采用透射电镜、氮气吸附-脱附、X射线粉末衍射、红外光谱测试手段对样品进行了表征.研究表明,以SD-BS为模板剂合成的介孔氧化锆具有蠕虫状介...     

合成介孔纳米晶体氧化锆的新方法(英文)

通过一种新颖的方法,即软模板-固液技术(CSSL)合成具有高比表面积的介孔纳米晶体氧化锆.首先,通过软模板法以1-十六烷基-3-甲基咪唑溴(C16mim+Br-)为结构导向剂,硫酸锆为无机前驱物合成了介观相氧化锆杂化物,然后该杂化物与固体硝酸铜无机盐研磨并进行热处理.在600℃焙烧后所得到的氧化锆材料具有蠕虫状介孔结构,且孔壁由尺寸约为2.50nm的四方相氧化锆纳米粒子组成.该材料的比表面积为240.0m2·g-1,孔径为4.10nm.与之对应,使用单一的软模板法在相同的温度焙烧后,所得到的氧化锆材料介孔结构坍塌,比表面积仅为9.5m·2g-1.     

模板剂和制备条件对介孔CeO2材料性能的影响

在碱性条件下,采用Brij35、Brij35 CTAB、Brij35 PEG20000为模板剂合成了m-CeO2,考察了模板剂种类、合成温度、老化温度及焙烧温度等因素对m-CeO2性能的影响,运用XRD、FT-IR、TEM、N2吸附-脱附和比表面-孔径测定等手段对m-CeO2进行了表征。结果表明,表面活性剂的种类、合成温度、老化温度及焙烧温度对介孔材料的性能有较大影响。以Brij35 CTAB为复合模板剂,合成温度、老化温度及焙烧温度分别为40℃、60℃及450℃时,所制备的m-CeO2-BC,其比表面积、孔容、平均孔径和孔壁厚度分别为137.9m2/g、0.194 cm3/g、4.9nm和0.010nm,且孔径分布较集中,晶粒尺寸为5.9nm,为纳米介孔材料。     

非表面活性剂合成CeO2介孔材料

以非表面活性剂三乙胺(TEA)和聚乙二醇(PEG)为模板剂,合成了具有立方莹石晶相结构的介孔CeO2材料,通过XRD,HRTEM,BET,FTIR和选区电子衍射(SAED)等手段对介孔CeO2进行了表征。考察了模板剂在CeO2介孔结构的形成过程中所起的作用及其对比表面、孔径分布、热稳定性的影响,并对模板剂的作用机制进行了分析。结果表明,三乙胺在CeO2介孔结构的形成中起关键作用,聚乙二醇对介孔结构热稳定性有明显的改善作用,经600℃焙烧3h的样品仍能保持较好的介孔结构,其介孔呈直通型的六方型孔道,比表面积>200m2·g-1,孔分布呈双孔型分布,其中介孔孔径约为5nm左右,微孔孔径在1～2nm之间,介孔占较大比例,并且微孔数量随焙烧温度的升高逐渐减少,直至600℃消失。     

掺杂TiO2介孔材料的合成与表征

基于溶胶-凝胶过程, 以非表面活性剂有机小分子三乙醇胺为模板剂, 合成了TiO2及Fe3+/V5+-TiO2介孔材料. 利用XRD, TEM, BET, UV-Vis DRS等手段表征了材料的结构、形貌、比表面积、孔径分布及吸光性能. 研究结果表明, 用乙醇萃取法脱除模板剂可形成具有蠕虫状孔道结构的TiO2介孔材料, 而利用焙烧法在450 ℃脱除模板剂时可引起孔道的塌陷. 掺杂Fe3+或V5+可稳定材料的介孔结构, 适宜的掺杂摩尔分数为0.5％. 于450 ℃下焙烧后, 掺杂Fe3+/V5+的TiO2的平均孔径分别为10.5和9.6 nm, 比表面积分别达到103.59和90.80 m2/g. 相对于P25光催化剂, 掺杂Fe3+或V5+的TiO2吸光带边红移至可见光区, 说明掺杂离子在此合成过程中可有效地进入TiO2的晶格结构而引起其微观电子结构的改变.     

介孔分子筛V-MCM-41的水热法制备与合成机理

 以十六烷基三甲基溴化铵为模板剂,廉价的工业级高模数比(3.3)的硅酸钠为硅源,通过水热法合成了V-MCM-41介孔分子筛. 考察了合成条件对产物织构的影响,并采用低温氮吸附法分析探讨了介孔分子筛V-MCM-41的合成机理. 结果表明,模板剂用量、 pH值、加料方式、晶化温度、晶化时间、陈化时间和焙烧气氛等合成条件对介孔分子筛的制备均有影响,其中晶化温度、 pH值和模板剂用量的影响最为明显. X射线衍射谱表明合成的介孔分子筛具有六方晶体结构. 红外光谱和紫外可见光谱表明V进入了介孔分子筛的骨架结构.     

以TEA为模板剂合成二氧化锆介孔分子筛热稳定性的研究

以丙醇锆为锆源、有机小分子三乙醇胺作为络合稳定剂和模板剂,通过水热合成途径制备了二氧化锆介孔分子筛.在不引入任何其他辅助离子的前提下,所得样品具有较好的热稳定性.通过TG-DTA,XRD,TEM等表征手段,考察了不同焙烧温度对二氧化锆介孔分子筛结构的影响,并对其机制进行了初探.     

介孔二氧化钛的合成及其对甲基橙降解的光催化活性

以十六烷基三甲基溴化铵为模板剂,通过水解钛酸正丁酯合成了介孔二氧化钛分子筛,探讨了合成条件的影响。采用X射线粉末衍射(XRD)、红外光谱(FT-IR)、透射电子显微镜(TEM)和N2吸附-脱附等技术对介孔二氧化钛的晶相、结构、形貌、比表面积和孔径分布进行了表征。实验结果表明:得到的介孔二氧化钛分子筛的孔径为4-4.3nm,用抽提的方法去除模板剂得到的介孔二氧化钛的比表面积比焙烧的要高。以甲基橙为模型污染物,检验了所合成介孔二氧化钛的光催化性质。     

酚醛树脂基球形微-介双阶多孔炭的软模板法制备

将苯酚和甲醛在碱性条件下聚合,然后在酸性条件下与软模板剂F127自组装形成中间相,经高温煅烧合成球形微-介双阶多孔炭。 通过扫描电子显微镜、透射电子显微镜、氮气吸附-脱附和热重分析技术对样品进行了形貌观察和性能测试。 结果表明,pH值、软模板剂用量和活化温度对样品形貌有调控作用。 当软模板剂F127的质量分数为20%、pH值为0.5和活化温度为700 ℃时,可制备出直径为100～200 nm的球形炭,球形粒子分散均匀,排列规整,呈明显蠕虫状排列的孔隙结构,比表面积为503 m2/g,孔容积0.416 cm3/g,介孔孔径集中分布在2.9 nm,微孔主要分布在1.3 nm。 随着活化温度升高,炭球的比表面积和孔容积增大,平均孔径减小。 F127的热解形成介孔结构,碳前驱体高温下的径向收缩形成微孔结构。     

甲苯和一氧化碳氧化用介孔LaFeO3催化剂（英文）

以KIT-6和二氧化硅纳米球为硬模板制备了比表面积分别为138和65 m2/g的正交相蠕虫状介孔LaFeO3催化剂LFO-1和LFO-2.在空速为20000 mL/(g劒h)的条件下,LFO-1样品显示出最高的催化活性:对于CO氧化反应,T50%和T90%分别为155和180 oC;对于甲苯氧化反应,T50%和T90%分别为200和253 oC.该样品优异的催化性能与它具有较大的比表面积、较高的氧吸附物种浓度、较好的低温还原性以及良好的蠕虫状介孔结构有关.     

Revealing the mechanisms behind SnO2 nanoparticle formation and growth during hydrothermal synthesis: an in situ total scattering study

The formation and growth mechanisms in the hydrothermal synthesis of SnO(2) nanoparticles from aqueous solutions of SnCl(4)·5H(2)O have been elucidated by means of in situ X-ray total scattering (PDF) measurements. The analysis of the data reveals that when the tin(IV) chloride precursor is dissolved, chloride ions and water coordinate octahedrally to tin(IV), forming aquachlorotin(IV) complexes of the form [SnCl(x)(H(2)O)(6-x)]((4-x)+) as well as hexaaquatin(IV) complexes [Sn(H(2)O)(6-y)(OH)(y)]((4-y)+). Upon heating, ellipsoidal SnO(2) nanoparticles are formed uniquely from hexaaquatin(IV). The nanoparticle size and morphology (aspect ratio) are dependent on both the reaction temperature and the precursor concentration, and particles as small as ~2 nm can be synthesized. Analysis of the growth curves shows that Ostwald ripening only takes place above 200 °C, and in general the growth is limited by diffusion of precursor species to the growing particle. The c-parameter in the tetragonal lattice is observed to expand up to 0.5% for particle sizes down to 2-3 nm as compared to the bulk value. SnO(2) nanoparticles below 3-4 nm do not form in the bulk rutile structure, but as an orthorhombic structural modification, which previously has only been reported at pressures above 5 GPa. Thus, adjustment of the synthesis temperature and precursor concentration not only allows control over nanoparticle size and morphology but also the structure.     

Novel synthesis of well-dispersed crystalline SnO2 nanoparticles by water-in-oil microemulsion-assisted hydrothermal process

Well-dispersed crystalline tin dioxide (SnO2) nanoparticles were synthesized by a novel and simple water-in-oil (w/o) microemulsion-assisted hydrothermal process, using low-cost tin chloride as the starting material. The typical quaternary microemulsions of cetyltrimethylammonium bromide (CTAB)/n-pentanol/n-hexane/water were used as space-confined microreactors for the nucleation, growth, and crystallization of SnO2 nanoparticles under hydrothermal conditions. The techniques of XRD, TEM, HRTEM, SAED, EDS, FTIR, XPS, and N2 adsorption measurement were used to characterize the compositions and structures of obtained samples. The results show that the SnO2 nanoparticles have high specific areas (107-169 m2 g(-1)), small particle sizes (ca. 3.0 nm), high crystallinity, and narrow size distributions. The well-dispersed, uniform, and well-crystallized powders with microporous texture are favorable for gas-sensing applications. The as-developed microemulsion-assisted in situ crystallizing process can be extended to prepare other oxide, metal, and sulfide nanoparticles.     

一氧化氮选择还原锡锆固溶体催化剂的结构特性

采用双股并流共沉淀方法制备了SnO2含量从10％至90％的锡锆体系DeNOx催化剂,用XRD、微区电子衍射、FT-Raman及FT-IR等技术深入研究了锡锆体系氧化物的结构及其随组成的变化规律.结果表明，由于Sn4＋与Zr4＋离子半径接近,SnO2与ZrO2易于形成固溶体,并随组成变化表现出不同的结构特征.纯ZrO2为单斜相,当少量Sn4＋（SnO2 ≤ 20％）进入ZrO2晶格时形成四方相富锆固溶体,Sn4＋起到稳定ZrO2四方相的作用;随着SnO2含量的增大,结构从无定形或微晶态的富锆固溶体(含SnO2 30～50％)经富锆固溶体与金红石结构的富锡固溶体在55％ SnO2含量的共存状态变化到具有金红石结构的富锡固溶体（SnO2 ≥ 60％）.FT-Raman和FT-IR光谱测试证明,Zr进入SnO2晶格使得Sn－O键的结合减弱,Sn离子上的有效正电荷减小,降低了SnO2对丙烯的燃烧能力,从而提高了对NO的还原活性.     

Hydrothermal routes to prepare nanocrystalline mesoporous SnO2 having high thermal stability

We report simple hydrothermal routes to prepare thermally stable SnO2 particles having high specific surface areas and mesoporosity. The preparation method includes a new combination of synthetic processes: hydrolysis of tin(IV) chloride at 95 degrees C in the absence of alkaline solutions (aqueous NH3 or NaOH), formation of nanocrystalline SnO2, and subsequent hydrothermal treatments at temperatures between 100 and 200 degrees C. After annealing treatments of the hydrothermally treated SnO2 particles at 400 or 500 degrees C, their crystallite sizes remained smaller than 7.7 nm and their specific surface areas were still higher than 110 m2/g, indicative of the high thermal stability against particle growth and sintering. Furthermore, mesoporosity evolved with a relatively narrow pore size distribution typically in the range of 3.0-4.3 nm. The effects of the hydrothermal treatment were explained by uniformization of the particle size that was beneficial to the suppression of particle growth.     

刷涂热分解法制备Ti/SnO2-Sb2O5阳极及其性能

通过刷涂热分解法制备了锑掺杂的钛基二氧化锡(Ti/SnO2-Sb2O5)涂层电极. 在酸性介质中, 用扫描电镜(SEM)、X射线衍射仪(XRD)、循环伏安和快速寿命测试等方法研究了Ti/SnO2-Sb2O5电极制备条件、电极结构、性能和寿命. 结果表明, Ti/SnO2-Sb2O5电极涂层具有“干泥”结构, 用锡锑摩尔比为9:1的涂液组成、在550 ℃烧结温度下制备的Ti/SnO2-Sb2O5的电极涂层平整致密,龟裂小, 电极孔隙率小, 稳定性最好.     

Synthesis, structure, texture, and CO sensing behavior of nanocrystalline tin oxide doped with scandia

Weakly agglomerated nanocrystalline scandia doped tin oxide powders with high surface area (170-220 m(2)/g) and uniform size (3-4 nm) were synthesized for the first time by a two-step hydrothermal process in the presence of urea, followed by the calcination between 500 and 1200 degrees C. The structure and texture of the binary oxide system were characterized by thermogravimetry and differential thermal analysis, Brunauer-Emmett-Teller-specific surface area analysis, transmission electron microscopy, X-ray diffraction, Raman spectroscopy, and X-ray photoelectron spectroscopy. A metastable scandium tin oxide solid solution in tetragonal structure was formed for the scandia content lower than 6 mol % as the samples were calcined at 800 degrees C, and the excess Sc atoms were dispersed at the surface of the crystallites above this limit. The solid solution was metastable, so scandium migrated toward the surface region of the crystallites and produced a second phase of Sc(4)Sn(3)O(12) during calcining at high temperatures over 1000-1200 degrees C. In the case of the samples with higher dopant concentration (>15 mol %), the calcination at the temperature between 500 and 800 degrees C caused the precipitation of Sc(2)O(3), and the calcination over 1000-1200 degrees C led to the formation of more Sc(4)Sn(3)O(12). Textural analysis showed that doping an appropriate amount of Sc(2)O(3) into nanosized SnO(2) could effectively inhibit the grain growth and stabilize the surface area against high-temperature calcinations below 1000 degrees C. CO gas-sensing property measurements revealed that the dispersion of Sc at the surfaces of the SnO(2) nanocrystallites could improve the CO sensitivity significantly, and the pellet sample with scandia content of 10 mol % sintered at 800 degrees C showed the best CO gas-sensing property in the operation temperature range of 300-400 degrees C. On the basis of the structural and textural analysis, the correlation between the structure/texture and the sensitivity to CO for the as-calcined (SnO(2))(1-x)(Sc(2)O(3))(x) nanocrystallites has been established and explained.     

Coagulation and stabilization of sterically functionalized magnetite nanoparticles in an organic solvent with different technical polymers

Single crystalline zinc tin oxide (ZTO) nanocrystallites were prepared at room temperature through association with a peptide-containing bolaamphiphile molecule. The bolaamphiphile molecules self-assembled to form spherical structures with creation of ZTO nanocrystallites inside. ZTO nanocrystallite synthesis was achieved only when the bolaamphiphile molecule was present, while a mixture of amorphous Sn and Zn precipitates was formed in the absence of the bolaamphiphile molecule. The bolaamphiphile molecule is thought to stabilize the Zn(2+) and Sn(4+) precursor ions by ligation and to induce subsequent condensation forming crystalline ZTO. The ZTO formation was achieved only at a strong acidic condition that promotes dissociation and ionization of Zn and Sn precursors and represses formation of ZnO and H(2)SnO(3). The prepared ZTO nanocrystallites had almost the same band gap energy as ZTO nanoparticles prepared by the conventional hydrothermal process. The outcomes of this study indicate that the controlled mineralization of metal precursor ions in a peptide-containing bolaamphiphile molecule suspension can be an alternative method to synthesize metal oxides at room temperature, while maintaining their crystalline structure and optoelectrical properties.     

Hydrothermal synthesis of Zn2SnO4 as anode materials for Li-ion battery

Spinel Zn2SnO4 particles with the cubic shape are prepared via a hydrothermal reaction under mild conditions. The hydrothermal conditions, such as alkaline concentration, reaction temperature, and duration time, have an important influence on the product structure and the performance of the electrode prepared with the product. The optimized product is cube-shaped Zn2SnO4 crystalline, which is prepared with 0.4 M of NaOH solution at 200 degrees C for 24 h. These cube-shaped Zn2SnO4 particles with the spinel structure exhibit a large electrochemical capacity of 988 mA h/g and a relatively good capacity retention as anode materials for Li-ion battery. The structures of the as-prepared product and specimens taken from the electrodes after charging-discharging cycles are analyzed by X-ray diffraction, scanning electron microscopy, and transition electron microscopy techniques. In particular, it is found for the first time that the spinel Zn2SnO4 structure exists to a great extent after the first cycle and contributes to the extremely high reversible capacity during the following cycles.     

乙二醇甲醚中电解锡电解液直接水解制备纳米SnO2

采用锡金属为阳极，在无隔膜电解槽中，电化学溶解锡于乙二醇甲醚中制备得到纳米SnO2前驱体Sn(OCH2CH2OCH3)4，将电解液直接水解经溶胶-凝胶法制备纳米SnO2，前驱体通过拉曼和红外光谱进行表征.纳米SnO2采用X射线粉末衍射(XRD)和透射电子显微镜(TEM)进行表征.实验表明,电解合成的Sn(OCH2CH2OCH3)4能够溶解于乙醇中, 适宜作为溶胶-凝胶(sol-gel)法制备纳米SnO2的原料，制得的纳米SnO2经600 ℃煅烧后呈球形单分散结构，晶型为四方锡石型, 比表面为62.58 m2·g－1，平均粒径在(10.0±0.4) nm左右.产率为89.3％，电流效率为86.9％.     

A new route to self-assembled tin dioxide nanospheres: fabrication and characterization

Nearly monodispersed self-assembled tin dioxide (SnO2) nanospheres with intense photoluminescence (PL) were synthesized using a new wet chemistry technique. Instead of coprecipitating stannous salts, bulk tin (Sn) metal was oxidized at room temperature in a solution of hydrogen peroxide and deionized water containing polyvinylpyrrolidone (PVP) and ethylenediamine (EDA). SnO2 nanocrystals were produced with diameters of approximately 3.8 nm that spontaneously self-assembled into uniform SnO2 nanospheres with diameters of approximately 30 nm. Analysis was performed by X-ray diffraction, scanning electron microscopy, energy-dispersive X-ray spectroscopy, high-resolution transmission electron microscopy, selected area electron diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, UV-vis absorption spectroscopy, PL spectroscopy, and fluorescence lifetime measurements. The SnO2 nanospheres displayed room-temperature purple luminescence with an intense band at 394 nm (approximately 3.15 eV) and a high quantum yield of approximately 15%, likely as a result of emission from the surface states of SnO2/PVP complexes. The present study could open a new avenue to large-scale synthesis of self-assembled functional oxide nanostructures with technological applications as purple emitters, biological labels, gas sensors, lithium batteries, and dye-sensitized solar cells.