PtSn/Al2O3/MCM-41催化剂的丙烷脱氢催化性能

用微型催化反应装置评价, 并结合X射线粉末衍射(XRD)、表面积和孔结构测试、程序升温还原(TPR)、氢化学吸附和热重分析等方法研究了负载型PtSn/γ-Al2O3, PtSn/MCM-41和PtSn/Al2O3/MCM-41催化剂的丙烷脱氢反应催化性能. 发现PtSn/Al2O3/MCM-41催化剂具有较PtSn/MCM-41催化剂高的丙烷脱氢反应活性和较PtSn/γ-Al2O3催化剂高的反应稳定性. 实验结果表明, 纯硅MCM-41载体表面的锡物种因与载体相互作用较弱故易被还原, 导致铂金属分散度和催化剂的丙烷脱氢活性较低. 用Al2O3修饰MCM-41可以增强Sn物种与Al2O3/MCM-41载体之间的相互作用, 提高PtSn/Al2O3/MCM-41催化剂铂金属分散度和丙烷脱氢催化活性. 并且, 积炭后的PtSn/Al2O3/MCM-41催化剂具有较高的铂金属表面裸露度, 故具有较高的丙烷脱氢反应稳定性. PtSn/Al2O3/MCM-41催化剂优良的丙烷脱氢催化性能可能不仅与Sn-载体Al2O3/MCM-41较强的相互作用有关, 而且与Al2O3/MCM-41载体的介孔结构有关.     

载体组成对负载型PtSn/ZSM-5催化剂上丙烷脱氢反应性能的影响

用微型催化反应装置结合吡啶吸附的红外光谱、NH3-程序升温脱附、热重、H2化学吸附和程序升温还原等物理化学手段研究了载体组成对负载型PtSn/ZSM-5催化剂上丙烷脱氢反应性能的影响.结果表明,负载型PtSn/ZSM-5催化剂对丙烷脱氢的催化性能与载体组成密切相关.随着ZSM-5载体中SiO2/Al2O3比的增加,催化剂表面的酸中心总量和强酸中心量逐渐减少.当SiO2/Al2O3摩尔比从45增至108时,催化剂对丙烷脱氢反应的催化活性提高,并且催化剂的积炭量下降.当SiO2/Al2O3摩尔比增至304时,Sn组分与载体ZSM-5之间的相互作用减弱,经H2还原后催化剂中Sn0物种所占的比例增加,导致催化剂H2化学吸附量和丙烷脱氢反应活性下降.     

HY/MCM-41/γ-Al2O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

 采用水热法合成了不同SiO2/Al2O3比的MCM-41介孔分子筛. 并分别以HY/MCM-41/γ-Al2O3, HY/γ-Al2O3和γ-Al2O3为载体,用浸渍法制备了Mo-Ni-P催化剂. 以萘为模型化合物,考察了硫化态Mo-Ni-P催化剂的加氢活性. 结果表明,不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高,其中掺杂大比表面MCM-41的HY/MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大. 由于MCM-41与HY分子筛在酸性和孔结构上存在互补性,因而催化剂对萘加氢存在协同作用. 提出了萘加氢的反应机理,认为反应网络包括两个平行路径: 一是萘加氢生成四氢萘后发生异构化或开环反应; 二是萘加氢生成四氢萘后进一步加氢生成十氢萘,继而发生异构化或开环反应.     

PtSnNa/SUZ-4:丙烷脱氢反应的高效催化剂

丙烷脱氢制丙烯是优化利用炼厂气和油田伴生气资源的一条重要途径.随着丙烯需求量的逐步增加,丙烷脱氢制丙烯日益受到重视.负载型PtSn/γ-Al2O3催化剂具有优良的丙烷脱氢活性和选择性,但在高温、低氢压的反应条件下,催化剂易积炭而失活.近年来,选用了微孔分子筛如ZSM-5和介孔分子筛如SBA-15和MCM-41作为PtSn催化剂的载体,结果表明,具有规整孔道结构的负载型PtSn/分子筛催化剂的丙烷脱氢反应稳定性明显优于PtSn/γ-Al2O3催化剂.SUZ-4分子筛与ZSM-5分子筛结构相似且孔径相当,所不同的是ZSM-5由十元环交叉孔道组成,而SUZ-4由十元环和八元环孔道垂直相交组成.我们用微型催化反应装置结合XRD、BET比表面积和孔体积测试、NH3吸附-程序升温脱附(NH3-TPD)、氢化学吸附、热重分析(TG)、H2程序升温还原(H2-TPR)和程序升温氧化(TPO)等多种物理化学手段研究了负载型PtSnNa/SUZ-4和PtSnNa/ZSM-5催化剂的结构和丙烷脱氢反应性能,以及这两种催化剂在丙烷脱氢反应中催化性能差异的原因.实验结果显示,在丙烷脱氢反应中,负载型PtSnNa/SUZ-4催化剂上丙烯选择性和反应稳定性明显优于PtSnNa/ZSM-5催化剂,说明载体一定程度上会影响催化剂上丙烷脱氢反应性能.XRD,BET比表面积和孔体积测试等表征手段结果表明,SUZ-4和ZSM-5的孔体积和比表面积比较接近,载体的结构又类似,且两者的积碳量也相近,故载体的基本性质和积碳量的差异不是引起催化剂性能差异的原因.NH3-TPD结果表明,H-SUZ-4的酸强度明显强于H-ZSM-5.由于浸渍法制备负载型PtSn催化剂所用前体为具有强酸性的混合溶液(H2PtCl6+SnCl4),存在于SUZ-4分子筛孔道内表面的强酸中心不利于上述前体与SUZ-4分子筛孔道内表面结合.ZSM-5分子筛孔道内表面比较弱的强酸中心,促进了催化剂前体在ZSM-5分子筛孔道内表面的分散与结合.和ZSM-5为载体的催化剂相比,PtSnNa/SUZ-4上Pt粒子大部分分散在载体的外表面,从而金属上的积碳不易引起催化剂的失活.故多孔材料上Pt的分布是影响催化活性差异的主要原因.为进一步证明多孔材料上Pt的分布是影响催化活性差异的主要原因,我们通过二苯并噻吩预处理催化剂的手段证明Pt粒子在分子筛孔内外的分布情况.由于二苯并噻吩的尺寸比较大(0.8 nm)不能进入到分子筛的孔道内(SUZ-4:0.56 nm,ZSM-5:0.56 nm),所以载体孔道外的部分Pt会被二苯并噻吩预处理而失去活性,而孔道内的Pt不会因为预处理仍具有催化活性.实验结果表明,PtSnNa/SUZ-4经过二苯并噻吩预处理后,催化活性大大降低;而PtSnNa/ZSM-5经过二苯并噻吩预处理后,催化活性几乎没有变化.说明PtSnNa/SUZ-4上Pt粒子大部分分散在载体的外表面,从而金属上的积碳不易引起催化剂的失活.     

纳米膜组装介孔Al2O3：合成及Pt/Al2O3的硝基苯催化加氢性能

以"乙酸乙酯(EA)-偏铝酸钠-水"体系在室温下合成了纳米膜组装介孔Al2O3。研究发现:合成反应时间、静置前搅拌时间、NaAlO2用量、EA用量及反应温度等对合成产物的形貌有影响;另外,与用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂相比,纳米膜组装介孔Al2O3制备的Pt/Al2O3催化剂含有部分易被还原的PtOx物种。在硝基苯催化加氢反应中,用合成Al2O3为载体制备的Pt/Al2O3催化剂,比用商品γ-Al2O3制备的Pt/γ-Al2O3催化剂具有更好的催化活性。     

添加碱土金属对负载型铂锡催化剂长链烷烃脱氢反应性能的影响

用微型催化反应装置结合吡啶吸附 红外光谱、热重、氢化学吸附和程序升温等还原手段,研究了添加碱土金属离子助剂对负载型PtSn/γ-Al2O3催化剂长链烷烃(C10~13)脱氢反应性能的影响。结果表明,碱土金属助剂的引入可以降低催化剂积炭量、提高催化剂铂金属表面裸露度,从而提高催化剂脱氢反应稳定性。但强碱性的碱土金属助剂如Ba2+的引入增强了锡与载体之间的相互作用,减弱了锡与铂之间的相互作用, 导致反应后催化剂铂金属表面裸露度下降,故PtSnBa/γ-Al2O3催化剂脱氢活性较低。     

Pt,Ru和Pd助剂对F-T合成中Co/γ-Al2O3催化剂性能的影响

 采用浸渍法制备了添加贵金属Pt,Ru和Pd助剂的Co/γ-Al2O3催化剂,并考察了它们在F-T合成反应中的催化性能. 结果表明,添加贵金属助剂可以显著提高Co/γ-Al2O3催化剂的催化活性. XRD和TPR表征结果表明,贵金属助剂不但可以使催化剂的金属分散度增加,而且可以通过氢溢流促进催化剂表面活性相的Co3O4以及与载体Al2O3有相互作用的非活性相钴氧化物物种的还原,从而改善催化剂的还原性能. TPSR结果进一步表明,添加贵金属助剂后催化剂对CO的吸附解离能力增强,从而使吸附态CO的加氢活性提高.     

Ca或Ce对PtSn/MCM-41催化剂的结构及催化丙烷脱氢性能的影响

制备了Ca或Ce改性的PtSn/MCM-41催化剂,利用XRD、N2吸附-脱附、TPR、TEM和TGA等技术对所制备的催化剂进行了表征,采用微型催化反应装置评价了其催化丙烷脱氢的性能,并分析了反应后催化剂的积炭情况。结果表明,PtSn/MCM-41催化剂中加入Ca或Ce助剂后,增强了丙烷脱氢催化性能,这不仅与助剂和活性组分之间的强烈相互作用有关,而且Ca或Ce助剂的加入会减少由于积炭而导致催化剂的失活。     

负载型MoO3 /γ-Al2O3催化剂中晶格氧的丙烷氧化脱氢反应性能

采用X射线衍射(XRD),氢气程序升温还原(H2-TPR)和无氧脉冲反应评价等研究了MoO3在γ-Al2O3载体表面的分散状态和负载型MoO3/γ-Al2O3催化剂晶格氧物种的丙烷氧化脱氢反应性能.结果表明在γ-Al2O3表面MoO3分散容量的实测值(4.73Mo6 /nm2)与按照"嵌入模型"估算的理论分散容量(4.90 Mo6 /nm2)接近.在分散容量以下,键合在γ-Al2O3表面孤立的Mo-O-Al物种倾向于分散在相邻的空位上且通过Mo-O-Mo化学键相连形成聚合的表面MoOx物种.随着MoO3负载量增加,Mo-O-Al键合方式逐步转变为Mo-O-Mo键合方式,钼离子周围的氧离子活泼性下降,导致丙烷氧化脱氢反应活性下降.超过分散容量以上的Mo离子以晶相形式存在.由于钼离子表面利用率下降,尤其是多层的晶相氧化钼表面Mo-O-Mo物种难以与载体表面铝离子键合,导致与钼离子相结合的氧离子可移动性下降、反应活泼性降低,催化剂的丙烷氧化脱氢反应活性急剧下降.     

Na-PtSnCe/γ-Al_2O_3丙烷脱氢催化剂的制备和催化性能

以γ-Al2O3为载体,采用连续等体积浸渍法,制备了一系列不同Na含量的Na-PtSnCe/γ-Al2O3催化剂,结合XRD、Py-IR、H2-TPR和TEM等手段对催化剂进行了表征,讨论了催化剂表面酸性及负载组分与载体之间的相互作用。采用微型催化反应装置考察了碱金属Na助剂含量和焙烧温度对负载型Na-PtSnCe/γ-Al2O3催化剂的丙烷脱氢反应性能的影响。结果表明,Na-PtSnCe/γ-Al2O3催化剂丙烷脱氢性能优于PtSnCe/γ-Al2O3催化剂,最佳Na含量为0.2%;适量Na助剂的添加可以降低催化剂的表面酸,增强催化剂中活性组分与载体之间的界面作用,提高催化反应的稳定性和选择性;550℃焙烧的Na-PtSnCe/γ-Al2O3催化剂,Pt组分与各助剂及载体之间的相互作用得到增强,催化剂具有最佳反应稳定性和最高丙烯选择性。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Carbon black and propylene oxidation over Ru/CoxMgyAl2Oz catalysts

The effects of Co_xMg_yAl₂O_z mixed oxides composition and ruthenium addition on the oxidation of propylene and carbon black (CB) were investigated. Different reactive cobalt and ruthenium oxide species were formed following calcination at 600 °C. The addition of ruthenium was beneficial for the CB oxidation under “loose contact” conditions and for propylene oxidation when the cobalt content was intermediate to low. The calculated activation energy for CB oxidation was decreased from 151 kJ mol⁻¹ for the uncatalyzed reaction to 111 kJ mol⁻¹ over the best catalyst.