熔融制样-X射线荧光光谱法测定锰铁中硅、锰、磷、铬、镍和铜

采用熔融制样-X射线荧光光谱法测定锰铁中硅、锰、磷、铬、镍和铜的含量。样品以四硼酸锂为熔剂,在300℃下加热15min,慢速升温至1 100℃,熔融15min,冷却后制成玻璃片,用于X射线荧光光谱分析。6种元素在一定的质量分数范围内与其信号强度呈线性关系,方法的检出限在15~59μg·g-1之间。方法用于锰铁样品的分析,测定值的相对标准偏差(n=11)在0.16%~3.6%之间。     

ICP–AES法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼的含量

建立电感耦合等离子体原子发射光谱(ICP–AES)法测定铬镍不锈钢中锰、铬、镍、硅、磷、铜、钼7种元素含量的方法。试样用盐酸与硝酸混合酸溶液溶解,采用溶解国家标准样品的方法制备校准曲线溶液,确定了元素最佳分析谱线。各元素的含量在其测试范围内与原子发射强度呈良好的线性关系,线性相关系数不小于0.999,7种元素的检出限在0.000 3%~0.003 0%之间。该方法应用于铬镍不锈钢标准样品的测定,测定值与认定值相符,测定值的相对标准偏差在0.12%~1.15%之间(n=8)。应用于铬镍不锈钢样品测定时,加标回收率在90%~110%之间。该方法操作简便、迅速,可满足日常铬镍不锈钢中多元素含量的检测需要。     

ICP–MS法测定食品接触纸制品中铬、镍、砷、镉、铅、汞

建立电感耦合等离子体质谱法(ICP–MS)测定食品接触纸制品中铬、镍、砷、镉、铅、汞6种重金属含量的方法。样品经微波消解处理后用ICP–MS进行测定,内标法定量。在优化实验条件下,测定汞元素的线性范围在0~10μg/L之间,测定铅、镉、铬、镍、砷元素的线性范围在0~100μg/L之间,相关系数均大于0.999。各元素的检出限为0.001~0.1 mg/kg,加标回收率为89.3%~116.0%,测定结果的相对标准偏差为3.5%~7.9%(n=6)。该方法样品处理简单,检测灵敏度高,适用于食品接触纸制品中铬、镍、砷、镉、铅、汞的检测。     

X射线荧光光谱法快速测定黑铜中的铜、砷、锑、铋、铅、镍、锌和锡

建立X射线荧光光谱法快速测定黑铜中的铜,砷,锑,铋,铅,镍,锌和锡等多种元素含量的方法。采用自制的黑铜样品作为标准样品建立标准工作曲线。实验确定了样品加工时最佳的铣样速度及谱线重叠干扰的校正方法,并用理论影响系数校正基体干扰。试验结果表明,各元素的工作曲线线性关系较好,线性相关系数均大于0.996。各元素的检出限在17~47μg/g之间。测定结果的相对标准偏差为0.038%~2.73%(n=7)。两个样品的测定结果与标准分析方法的测定结果相符。该方法具有较好的准确度和精密度,分析速度快,能满足炉前快速分析的需要。     

扫描型X射线荧光显微分析仪测定汽车零部件及内饰材料中铅、镉、汞、铬和溴

建立扫描型X射线荧光显微分析仪测定汽车零部件及内饰材料中铅、镉、汞、铬和溴等元素的方法。通过改变测量条件与测量方式选择最佳试验方法,采用成像图判断样品中是否存在目标元素。结果表明,5种元素的含量在0~300 mg/kg范围内与荧光强度成良好的线性关系,相关系数均大于0.993,样品加标回收率为82.3%~106.0%,测定结果的相对标准偏差为2.86%~6.63%(n=6)。该方法简单、快速,测定结果准确、可靠,适用于汽车零部件和内饰材料中有毒有害物质的筛选。     

石墨消解–火焰原子吸收光谱法测定土壤和沉积物中铜、锌、镍、铬

建立石墨消解–火焰原子吸收光谱法测定土壤和沉积物中铜、锌、镍、铬4种重金属的含量。采用盐酸–硝酸–氢氟酸–高氯酸作为消解体系对样品进行消解,铜、锌、镍以1%硝酸定容,铬以3%盐酸定容,采用火焰原子吸收光谱仪进行测定。铜、锌、镍、铬的质量浓度在0.00~1.00 mg/L范围内与吸光度均呈良好的线性关系,相关系数为0.999 4~0.999 5,方法检出限为0.7~1.5μg/g。测定结果的相对标准偏差为1.8%~3.4%(n=6),样品加标回收率为92.0%~105%。土壤和沉积物标准样品的测定值均在标准值可接受范围内。该方法操作简单、快速,结果准确、可靠,适用于土壤和沉积物样品中铜、锌、镍、铬等金属元素的测定。     

电感耦合等离子体发射光谱法测定不锈钢中的铬、镍、锰、铜、钛、铝

建立电感耦合等离子体发射光谱仪同时测定不锈钢中铬、镍、锰、铜、钛、铝6种元素含量的方法。用20mL王水溶解样品,铬、镍、锰、铜、钛、铝的分析谱线分别为283.563,231.604,259.373,324.754,334.941,308.215 nm。铬、镍、锰、铜、钛、铝的质量浓度与其信号强度均呈良好的线性关系,线性相关系数均不小于0.999,检出限分别为0.007,0.009,0.002,0.007,0.002,0.008μg/mL。测定结果的相对标准偏差为0.17%～2.80%(n=6),加标回收率为96.50%～103.70%。用该法测定国家标准物质,测定值与标准值一致,相对误差为0.05%～3.03%。该方法准确、可靠,可用于不锈钢中铬、镍、锰、铜、钛、铝的测定。     

波长色散X射线荧光光谱法测定钴精矿中钴、铜和锰含量

采用高纯氧化物经四硼酸锂和偏硼酸锂熔融制备人工标准样品,以氧化镱为内标,制作校准曲线,建立了波长色散型X射线荧光光谱法测定钴精矿中钴、铜、锰元素的分析方法。重点研究了混合熔剂、试样稀释比、氧化剂和内标选择、方法检出限、方法准确度和精密度等,结果表明,各元素校准曲线线性范围宽,相关系数均大于0.999, 钴、铜、锰元素检出限分别达到0.002%、0.001%和0.001%,测试准确度和精密度可靠,方法满足行业检测需求。     

无载体离子有机共沉淀分离-石墨炉原子吸收光谱法测定海水中铜铅铬镍

以吡咯烷二硫代氨基甲酸铵(APDC)氧化物作为共沉淀剂,建立了无载体离子有机共沉淀分离、石墨炉原子吸收光谱法测定海水中铜、铅、铬、镍的方法。考察了海水样品pH、共沉淀剂APDC和氧化剂H_2O_2的用量、陈化时间等因素对共沉淀分离效果的影响,优化了实验条件。结果证明,在p H4~5的海水样品中,加入4 m L 30 g/L APDC,1 m L H_2O_2,静置60 min,待测元素能与海水基体很好的分离。铜和铬含量在0~20μg/L范围内呈良好的线性关系,线性相关系数R0.999;镍含量在0~30μg/L,铅含量在0~40μg/L范围内呈良好的线性关系,线性相关系数R0.998;检出限分别为0.31,0.30,0.20,0.25μg/L,方法精密度好,加标回收率为88.8%~101.4%。方法可用于海水样品中铅、铜、镍、铬的常规检测。     

X射线荧光光谱法测定农田底泥中8种元素

建立X射线荧光光谱法测定农田底泥样品中砷、铬、铜、锰、镍、铅、锌、铁8种元素含量的分析方法.以塑料环粉末压片法制样,选用50种土壤、水系沉积物标准物质拟合校准曲线,探讨各元素的测定条件.当待测样品与建立校准曲线的标准样品粒径均小于75μm时,能够有效减少矿物效应和粒度效应的影响,从而提高检测准确度;各元素在各自的含量范...     

波长色散X射线荧光光谱无标分析法检测树脂中的铅

建立波长色散X射线荧光光谱检测树脂中重金属元素的无标样分析方法。热塑性塑料在200℃热压成样片;热固性塑料取平面直接测量;涂料研磨成粉末后用硼酸镶边、衬底,经过压样机20 t压力30 s压制成样片。所有样品在真空模式下,以激发电流为50 mA,激发电压为60 kV,分光晶体为LiF(200),准直器为0.23°,测量谱线为Pb Lβ1,峰位(2θ)为28.258的仪器工作条件下测定树脂中铅的含量,通过康普顿比率判断结果的可信度。测定值与标准方法检测值相比,偏差小于10%,测定结果的相对标准偏差小于1%(n=6)。结果表明,波长色散荧光光谱无标分析方法可以快速准确地分析树脂样品中的铅含量。     

氢化物发生–原子荧光法测定无机盐类食品添加剂中的铅

建立了氢化物发生–原子荧光光谱法测定无机盐类食品添加剂中铅的分析方法。考察了仪器工作条件、载流的酸度、还原剂浓度、氧化剂和掩蔽剂的用量以及共存元素对测量体系的影响。在优化实验条件下,该方法的线性范围为0~60μg/L(r=0.999 7),方法检出限为3.3μg/kg。以5种无机盐类食品添加剂为例,加入铅的质量浓度分别为12,24,48μg/L,每种浓度均进行6次平行测定,铅的回收率在95.0%~103.8%之间,测定结果的相对标准偏差为1.05%~2.71%(n=6)。该法适用于食品添加剂的质量控制和日常检测。     

密闭罐溶样–氢化物发生–原子荧光光谱法测定中药中的汞和砷

建立了密闭罐溶样–氢化物发生–原子荧光光谱法测定中药中痕量汞和砷的分析方法。采用密闭罐溶解复杂基体中药样品,进行易挥发元素分析的样品前处理,技术简单,快速,能耗低。汞和砷的质量浓度分别在0~10μg/L和0~200μg/L范围内与荧光强度成线性关系,线性相关系数均大于0.99。汞、砷的检出限分别为0.014,0.086μg/L;测定结果的相对标准偏差不大于4.67%(n=5);加标回收率分别为99.0%~106.4%,95.2%~101.7%。该方法操作简便,可用于中药中汞、砷元素的质量控制。     

Quantitative analysis of elements (C, N, O, Al, Si and Fe) in polyamide with wavelength dispersive X-ray fluorescence spectrometry

A wavelength dispersive X-ray fluorescence (WD-XRF) spectrometry combined with calibration curve method was established for simultaneously analyzing low-Z elements (C,N,O) and Al,Si,Fe in polyamide.To investigate the origin of plastic material causing deposition and blocking in instrument engines and pipelines,polyamide 6 (PA 6,an engineering plastic) was chosen as the study object on account of its common use in industry.The sample preparation with pressed powder disk has been developed for determination of six elements in PA 6.Pure Cu metal was used as the matrix and PA 6 was regarded as standard sample for C,N,O elements.PA 6 particles were firstly smashed to uniform powder in liquid nitrogen,and then mixed with inorganic standard powders (Fe2O3,Al2O3,SiO2,and Na 2 SiO 3).The mixture was ground to obtain homogeneous calibration materials for WD-XRF analysis.The quantitative property of the calibration curve method for each element was reliable.The limits of detection (S/N≤3) of C,N,O,Al,Si and Fe using WD-XRF were 249,120,101,6.2,3.3,and 1.8 μg/g,respectively.To confirm the accuracy of the proposed WD-XRF calibration curve method,inductively coupled plasma optical emission spectroscopy (ICP-OES) detection for Al,Si,Fe and elemental analyzer (EA) analysis for C,N,O were utilized.A good correlation of the WD-XRF results with the measurements of ICP-OES and EA was observed.     

X-射线荧光光谱法快速测定半钢发热剂中Si,P,S

目前,国内没有关于半钢发热剂的国家标准检测方法,只能根据组分范围分别检测各个组分,不仅耗时而且使用的大量化学试剂对环境造成污染。故研究了X-射线荧光光谱法快速测定半钢发热剂中Si,P,S的方法。采用粉末压片制样,研究其制样条件,包括磨样时间、压样时间和压力对测定结果的影响。采用其它方法定值提供的检测样品,作为X-射线荧光光谱法内控标准样品,采用经验系数法进行基体校正,通过解谱拟合建立校准曲线,校准曲线建立后仪器建立漂移校正程序。实验结果精密度好,各元素的相对标准偏差在0.15%~1.3%。准确度满足生产需求,实验方法可用于快速检测半钢发热剂化学组分。     

Direct determination of uranium in sintered deeply depleted uranium oxide pellets by wavelength dispersive X-ray fluorescence spectrometry

This paper presents studies on direct non-destructive determination of uranium in sintered deeply depleted (DD) uranium oxide (UO₂) pellets by wavelength dispersive X-ray fluorescence (WDXRF) spectrometry. A special collet was designed and fabricated for holding the sintered DDUO₂ pellets for direct analysis, thus avoiding the sample preparation steps. The samples were analyzed using a calibration plot obtained from WDXRF spectra of matrix matched calibration standards. The WDXRF determined uranium values were found to be in very close agreement with titrimetric values and has reproducibility better than 0.05% (RSD, 1 s, n = 10) for the sintered DDUO₂ pellets having U: 86.81–88.04 wt%.

     

Energy dispersive X-Ray fluorescence determination of thorium in phosphoric acid solutions

Energy dispersive X-ray fluorescence studies on determination of thorium (in the range of 7 to 137 mg/mL) in phosphoric acid solutions obtained by dissolution of thoria in autoclave were made. Fixed amounts of Y internal standard solutions, after dilution with equal amount of phosphoric acid, were added to the calibration as well as sample solutions. Solution aliquots of approximately 2–5 µL were deposited on thick absorbent sheets to absorb the solutions and the sheets were presented for energy dispersive X-ray fluorescence measurements. A calibration plot was made between intensity ratios (Th Lα/Y Kα) against respective amounts of thorium in the calibration solutions. Thorium amounts in phosphoric acid samples were determined using their energy dispersive X-ray fluorescence spectra and the above calibration plot. The energy dispersive X-ray fluorescence results, thus obtained, were compared with the corresponding gamma ray spectrometry results and were found to be within average deviation of 2.6% from the respective gamma ray spectrometry values. The average precision obtained in energy dispersive X-ray fluorescence determinations was found to be 4% (1σ). The energy dispersive X-ray fluorescence method has an advantage over gamma ray spectrometry for thorium determination as the amount of sample required and measurement time is far less compared to that required in gamma ray spectrometry.     

原子荧光光谱法测定铜合金中铋元素含量方法改进

基于原子荧光光谱法测定铋元素时检出限低、测定结果稳定且准确等优点,研究原子荧光光谱法测定铜合金中铋元素含量的方法。在标准系列中加入相近浓度的铜元素标准溶液,原子荧光光谱法测定铜合金中铋元素含量。称取0.1 g样品,加入10 mL硝酸溶解,10%硫脲-5%抗坏血酸溶液7.5 mL预处理样品。在20μg/L的铋标准溶液中加入6 mL浓度为1000μg/mL的铜元素标准溶液。结果表明:在0~20μg/L范围内,该方法线性关系良好,线性方程为I=138.1670c+43.8572,相关系数为0.9996,所测定的样品中铋元素含量的相对误差在-4.3%~7.7%之间,精密度在0.4%~4.7%之间。原子荧光光谱法可作为铜合金中铋元素含量测定的方法。     

氢化物发生-原子荧光光谱法同时测定水中砷和锑

建立在硝酸介质中用氢化物发生-原子荧光光谱法同时测定水中砷和锑的方法。优化了仪器工作条件、酸度、硼氢化钾及还原剂浓度。砷、锑的线性范围为0～10．0μg／L;检出限分别为0．02,0．01μg／L;测定结果的相对标准偏差分别为1．77％～3．72％,2．95％～4．87％（n=6）;加标回收率分别为98％106％,96％105％。该法操作简便,灵敏度高,快速,便于推广,适用于水中砷和锑的同时测定。