"一步法"合成多级孔SAPO-34分子筛

以TPOAC和硅溶胶为硅源,合成了多级孔SAPO-34分子筛,总比表面积达到649 m²·g^-1。详细考察了TPOAC和硅溶胶的配比对多级孔SAPO-34外比表面的影响,通过XRD、BET、SEM、NH₃-TPD等对其结构进行表征,结果表明多级孔SAPO-34的外比表面积可调变,晶体外观有较多缺陷位置,弱酸量减少,强酸位有变弱的趋势。在TPOAC与硅溶胶的投料比为3:2,晶化时间为10 d,投料比为n_Al2O3:n_P2O5:n_Si:n_TEAOH:n_H2O=1:0.9:0.5:2:60时,合成的多级孔SAPO-34的外比表面积达到最大,为100 m²·g^-1。     

具有纳米线镶嵌结构ZSM-5/L复合分子筛的合成及表征

采用两步晶化法,以四丙基氢氧化铵预处理ZSM-5为晶种,快速合成了纳米线镶嵌结构ZSM-5/L复合分子筛.通过XRD、SEM-EDX、TEM和N₂吸附-脱附等手段对合成样品的物理化学性质进行了表征.孔道性质表明复合分子筛具有微孔和介孔的多级孔道结构,椭球的L分子筛镶嵌在纳米线的ZSM-5分子筛周围.晶种预处理影响了溶胶的电荷及分子筛的形貌,当合成样品中ZSM-5的质量分数小于2%（重量百分比）时,凝胶的负电荷较多,易形成椭球状L分子筛;当合成样品中ZSM-5的质量分数大于2%（重量百分比）时,zeta电位在-39.822~-42.352 mV之间波动,ZSM-5分子筛的形貌从长条状逐渐转变为纳米线状.阳离子比影响复合分子筛中L分子筛形成,当阳离子比R=n（K₂O）/（n（K₂O）+n（Na₂O））小于0.6时,不利于L型分子筛的形成;当阳离子比大于0.6,即K⁺较多Na⁺较少时,有利于L型分子筛中α-钙霞石笼的形成.     

类固相法快速合成高钙镁离子交换性能的P型分子筛

以硅铝干凝胶为硅源和铝源,氢氧化钠为碱源,采用类固相法快速合成了P型分子筛,并通过X射线衍射（XRD）、扫描电镜（SEM）等手段对产品进行了表征分析。结果表明,硅铝干凝胶的组成n_SiO2/n_Al2O3=5,晶化时间和晶化温度分别为3 h、140℃,原料的组成n_Na2O/n_SiO2、n_H2O/n_SiO2=18.51时,可制备形貌均一、结晶良好的P型分子筛产品。与传统水热法相比,该方法极大地减少了合成过程的用水量,缩短了晶化时间,提高了产品的钙镁离子交换性能,从整体上优化了P型分子筛的合成工艺。     

碳酸盐共沉淀法可控制备超高倍率锂离子电池正极材料LiNi1/3Co1/3Mn1/3O2

采用碳酸盐共沉淀法通过调节NH₃·H₂O用量来实现可控制备超高倍率纳米结构LiNi_1/3Co_1/3Mn_1/3O₂正极材料。NH₃·H₂O用量会对颗粒的形貌、粒径、晶体结构以及材料电化学性能产生较大的影响。X射线衍射（XRD）分析和扫描电镜（SEM）结果表明,随着NH₃·H₂O用量的降低,一次颗粒形貌由纳米片状逐渐过渡到纳米球状,且n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品晶体层状结构最完善、Li⁺/Ni²⁺阳离子混排程度最低。电化学性能测试结果也证实了n_NH3·H2O：（n_Ni+n_Co+n_Mn）=1：2样品具有最优异的循环稳定性和超高倍率性能。具体而言,在2.7~4.3 V,1C下循环300次后的放电比容量为119 mAh·g^-1,容量保持率为81%,中值电压基本无衰减（保持率为97%）。在100C（18 Ah·g^-1）的超高倍率下,放电比容量还能达到56 mAh·g^-1,具有应用于高功率型锂离子电池的前景。此NH₃·H₂O比例值对于共沉淀法制备其他高倍率、高容量的正/负极氧化物材料具有一定的工艺参考价值。     

Cu、N共掺杂TiO2纳米管光催化重整甘油制备合成气

通过碱性水热-离子交换法制备了Cu、N共掺杂TiO₂纳米管(Cu/N-TNT),对其光催化重整甘油制备合成气性能进行了研究。结果表明,Cu/N-TNT具有富含氧空位(O_V)的管状结构,N以Ti-N形式取代部分O形成杂质能级,Cu以Cu²⁺形式掺杂在催化剂晶格间隙和表面,Cu、N共掺杂促进TiO₂表面电荷有效分离,有利于其光催化重整甘油制备合成气活性和选择性的提高。紫外光照射8 h时,掺Cu量为0.15%的Cu/N-TNT催化剂上CO和H₂产量分别为7.3和8.5 mmol·g^-1,是原始TiO₂的9.1和70.8倍,n_H2/n_CO从0.52提高为1.18,n_CO/n_CO2从0.21提高至0.42。Cu/N-TNT表面N和O_V为醛类脱羰和甲酸脱水生成CO提供反应活性位点,Cu作为浅势阱提高光生电子-空穴分离效率。光生空穴(h⁺)是光催化重整甘油制备合成气过程中的主要活性物种,大量羟基自由基(·OH)和超氧自由基(·O₂^-)会导致甘油过度氧化,使CO选择性降低。     

Bi9P2O18Cl的相变及其可见光催化水产氢

采用高温熔盐法制备了Bi₉P₂O₁₈Cl单晶。单晶X射线衍射分析表明Bi₉P₂O₁₈Cl从室温到低温发生晶体到晶体的相变。室温下,该化合物（α相）属于单斜空间群P2₁/m （11）,单胞参数： a=1.149 10（7） nm,b=0.540 64（4） nm,c=1.463 69（9） nm,β=93.741（6）°,V=0.907 38（10） nm³;而在100 K下,该化合物（β相）属于单斜空间群P2₁/n （14）,单胞参数： a=1.790 56（4） nm,b=0.538 870（10） nm,c=1.915 57（4） nm,β=103.693（2）°,V=1.795 76（6） nm³。另外,采用高温固相反应法,合成了高纯的Bi₉P₂O₁₈Cl粉末样品,该样品展示了较好的光催化产氢性能,产氢量可达33.69 μmol·g^-1·h^-1。     

T型分子筛膜的合成、表征与渗透汽化性能

采用二次生长法,在不锈钢、α-Al₂O₃和莫来石多孔管状支撑体上分别合成了高渗透汽化性能的T型分子筛膜。考察了合成条件如合成时间、n(SiO₂)/n(Al₂O₃)、n(H₂O)/n(Al₂O₃)和硅源等对T型分子筛膜形成和分离性能的影响。通过XRD和SEM表征了膜的晶相和形貌。     

二丙胺的结构微调对磷酸铝分子筛晶化过程影响的凝胶组成依赖性

以二丙胺异构体（二正丙胺DPA和二异丙胺D-iPA）为结构导向剂,在200℃加热2组反应原料物质的量之比不同的初始凝胶,合成出了高结晶度的磷酸铝分子筛AlPO₄-11。利用X射线粉末衍射分析、元素分析等表征手段,研究了凝胶的晶化过程和液相的pH值以及Al和P的浓度演化。初始凝胶各组分物质的量之比为n_Al2O3：n_P2O5：n_DPA/D-iPA：n_H2O2=1.0：1.0：1.2：75时,以DPA为结构导向剂,晶化过程中无中间相生成,而以D-iPA为结构导向剂时,晶化过程中生成了具有12元环孔道结构的磷酸铝分子筛AlPO₄-5中间相;初始凝胶各组分物质的量之比为n_Al2O3：n_P2O5：n_DPA/D-iPA：n_H2O2=1.0：1.0：1.0：75时,以DPA为结构导向剂,晶化过程中生成了具有18元环孔道结构的磷酸铝分子筛VPI-5中间相,而以D-iPA为结构导向剂时,晶化过程中同时出现了VPI-5及AlPO₄-5两种中间相。表明对于同一种有机胺,凝胶物质的量之比的改变影响了其结构导向效应。理论计算结果显示质子化的DPA及D-iPA中N原子上的电荷有差异,表明有机胺的结构微调影响其结构导向效应,但该影响依赖于凝胶组成。     

酸处理对CuY催化剂孔结构及氧化羰基化性能的影响

对NaY分子筛(n_Si/n_Al=2.65)进行了草酸脱铝处理并作为载体采用液相离子交换法制备CuY催化剂, 应用于常压甲醇氧化羰基化合成碳酸二甲酯(DMC)反应。NaY分子筛及其CuY催化剂通过N₂低温吸附-脱附、透射电子显微镜、X射线衍射、²⁹Si固体核磁共振、NH₃吸附程序升温脱附、吡啶吸附红外光谱、H₂程序升温还原、原子吸收等方法进行表征。研究结果表明, 酸处理NaY分子筛后, 骨架铝被脱除, 导致骨架n_Si/n_Al比增加、相对结晶度降低并产生介孔, 有利于产物分子的扩散, 从而影响催化活性。采用4 h、2 mol·L^-1草酸处理NaY分子筛作为载体制备的CuY催化剂显示出较高的催化性能, DMC时空收率和甲醇转化率分别从103.6 mg·g^-1·h^-1和6.3%增加到184.9 mg·g^-1·h^-1和10.2%。产生的介孔能够促进催化剂中铜活性位的可接近性及反应物分子和产物分子的扩散。     

立方介孔相含钕氧化硅的合成与表征

以十六烷基三甲基溴化铵为结构导向剂，通过水热法合成了具有立方结构的含钕Nd-MCM-48介孔分子筛材料。XRD和TEM测试表明当n_Nd/n_Si<0.05时可以获得典型的长程有序介孔立方结构相，随n_Nd/n_Si比的增加，晶胞参数的增大和红外吸收光谱(FT-IR)的变化为Nd进入介孔分子筛骨架中提供了有力证据。N₂吸附-脱附实验给出了其BET表面积为1 195 m²·g^-1，BJH平均孔径为3.6 nm。紫外-可见漫反射光谱(UV-Vis)证明钕氧形成一种八面体结构。X射线光电子能谱(XPS)进一步证明钕主要以三价形式存在于立方介孔分子筛骨架中。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.