ZnZr/HZSM-5复合催化剂上CO2加氢制备C5+异构烷烃

本研究将锌锆氧化物(ZnZr)与HZSM-5分子筛有效耦合制得系列ZnZr/HZSM-5复合催化剂,考察了HZSM-5硅铝比及Zn/Zr比对复合催化剂上CO₂加氢制备C₅₊异构烷烃性能的影响。结果表明,SiO₂/Al₂O₃=130,Zn/Zr=1∶5制得的ZnZr-4/HZSM-5复合催化剂表现出最优的CO₂加氢制C₅₊异构烷烃性能,CO₂转化率为17%,CO选择性抑制到25%,C₅₊烃及C₅₊烃中异构烷烃选择性分别达60%及89%。该复合催化剂稳定性良好,连续运转120 h未出现失活现象。ZnZr氧化物与HZSM-5分子筛的良好匹配对CO₂加氢高选择性合成C₅₊异构烷烃至关重要。     

N_2O在Cu_xFe_(1-x)Fe_2O_4和Ni_xFe_(1-x)Fe_2O_4复合氧化物催化剂上的分解反应

用共沉淀法制备了一组具有尖晶石结构的Cu-Fe和Ni-Fe复合氧化物,用于有氧条件下催化分解N2O,考察了催化剂组成对催化活性的影响.用N2物理吸附(BET)、X射线衍射(XRD)、H2程序升温还原(H2-TPR)等技术对催化剂进行了结构表征.结果表明:在不同组成的Cu-Fe、Ni-Fe系列复合氧化物催化剂中,Cu Fe2O4和Ni Fe2O4对于N2O分解反应的初活性较高,这是因为Cu Fe2O4和Ni Fe2O4的比表面积较高、晶粒较小,而且其表面氧物种与金属(Cu2+、Fe3+)的化学作用较弱,氧物种易脱除、脱氧量较高.相比较而言,Ni Fe2O4催化剂上的N2O分解活化能低于Cu Fe2O4,Ni Fe2O4的初活性优于Cu Fe2O4.500℃连续反应100 h,Cu Fe2O4上的N2O转化率降至84.9%,而Ni Fe2O4上的N2O转化率一直保持99%,Ni Fe2O4有较高的催化稳定性.     

Fe-Zn-M/HZSM-5复合催化剂上CO_2加氢性能的研究

研究了 380℃、 5 .0 MPa条件下 ,在 Fe- Zn- M/ HZSM- 5 (M=Cr、 Al)复合催化剂上进行的 CO2 催化加氢的反应 .考察了 Fe- Zn- M中 Fe含量、分子筛的硅铝比及 Fe- Zn- M/ HZSM- 5的比率对 CO2 转化率和产物选择性的影响 .结果表明 ,随着 Fe含量的增加 ,复合催化剂的活性增强、目的产物选择性降低 ;Fe- Zn- M与 HZSM- 5间有适宜的配比 ;分子筛的硅铝比影响到复合催化剂的活性和选择性 ,随着分子筛硅铝比的降低 ,复合催化剂的活性增强 ,目的产物选择性提高     

碳四烃在改性HZSM-5分子筛上芳构化研究

研究了炼厂混合C_4烃在Zn、Ga、Cr、La改性的HZSM-5分子筛催化剂上的芳构化反应,采用TPD和IR测定了催化剂的表面酸性质。结果表明,用Zn(3%)和Zn(2%)Ga(1%)改性的HZSM-5分子筛具有较好的芳构化性能;各改性HZSM-5分子筛催化剂芳构化性能变化与表面酸性有关,总酸量下降,芳构化活性下降,强B酸中心减少,深度裂解反应减少;Zn的单组分和双组分改性的HZSM-5分子筛催化剂芳构化活性的增高与表面强L酸浓度增加和吡啶吸附IR谱中的1615cm~(-1)吸收峰出现有关。     

Fe—Zn—M／HZSM—5复合催化剂上CO2加氢性能的研究

研究了380℃、5.0MPa条件下,在Fe-Zn-M/HZSM-5(M=Cr、Al）复合催化剂上进行的CO2催化加氢的反应,考察了Fe-Zn-M中Fe含量、分子筛的硅铝比及Fe-Zn-M/HZSM-5的比率对CO2转化率和产物选择性的影响。结果表明,随着Fe含量的增加,复合催化剂的活性增强、目的产物选择性降低;Fe-Zn-M与HZSM－5间有适宜的配比;分子筛的硅铝比影响到复合催化剂的活性和选择性,随着分子筛硅铝比的降低,复合催化剂的活性增强,目的产物选择性提高。     

载体对担载Ni催化剂甲烷与二氧化碳重整反应活性的影响

制备了 Zr O2 、Mg O改性的 Al2 O3、Ti O2 复合载体 ,并应用 X-射线粉末衍射 (XRD)、比表面积测定、扫描电镜 (SEM)等手段进行了表征 .结果表明 ,这些氧化物在 Al2 O3上的晶粒尺寸小、比表面积大 ,分散较好 ,而在Ti O2 上的分散性较差 .对经 10 73K焙烧的 Mg O/ Ti O2 ,还发现部分 Ti O2 载体由锐钛矿变为金红石 ,同时生成Mg Ti O3 新相 .考察了载体对 Ni催化剂的 CH4与 CO2 重整反应活性的影响 ,其次序为 :Mg O/ Al2 O3>Zr O2 /Al2 O3>Al2 O3>Mg O >Zr O2 >Ti O2 >Mg O/ Ti O2 . Ti O2 及 Mg O/ Ti O2 担载 Ni催化剂的低活性可能与 Ti O2 本身的还原性有关     

乙酸乙酯在Al2O3-Ce0.5Zr0.5O2负载的金属氧化物催化剂上的催化燃烧

制备了Fe, Co, Cu, Cr和Mn金属氧化物催化剂, 所用载体为Al2O3-Ce0.5Zr0.5O2复合氧化物. 利用X射线衍射(XRD), 程序升温还原(TPR), 储氧量测试, BET比表面测试和光电子能谱(XPS)表征了催化剂. 并利用活性测试表征了各种催化剂对乙酸乙酯催化燃烧能力. 各种表征结果证实, 由于催化剂Mn/Al2O3-Ce0.5Zr0.5O2(1:2, 质量比)具有最多的可还原物种, Cu/Al2O3-Ce0.5Zr0.5O2(1:2)具有较多的可还原物种和最强的可还原能力, 使它们对乙酸乙酯催化燃烧表现出了最好的活性. 在催化剂Cu/Al2O3-Ce0.5Zr0.5O2(1:2)和Mn/Al2O3-Ce0.5Zr0.5O2(1:2)上, 乙酸乙酯于245 ℃转化了99%, 表明这两种催化剂具有广泛的应用潜力.     

Ni-Fe/La2O2CO3催化乙醇水蒸气重整制氢的研究

采用La2(CO3)3空气焙烧法制备了La2O2CO3载体、采用浸渍法制备了Ni,Fe不同比例的Ni-Fe双金属催化剂及Ni/La2O2CO3,Fe/La2 O2 CO3催化剂,考察了各催化剂从300～700℃催化乙醇水蒸气重整反应的性能,并用BET,XRD,TPR等技术对催化剂进行表征。结果表明,相对单一金属催化剂,Ni-Fe双金属催化剂均表现出更高的活性,这可能是因为高分散的Ni,Fe和LaFeyNi1-yO3的共存作用。其中Ni含量为10%,Fe含量为5%时的Ni-Fe/La2O2CO3表现出最高的活性,400℃时乙醇的转化率为100%,H2的选择性最高达到94.1%,而CO的选择性则低至1.2%。     

CO氧化反应中H2O对MOx和Au/MOx催化性能的影响

过渡金属氧化物［1,2］及负载型贵金属催化剂［3～13］是催化氧化消除CO的有效催化剂,一直是研究的热点. 虽然对MOx和Au/MOx上CO的氧化性能研究得较多,但大多是在无水条件下进行的;涉及催化剂抗水性能的报道较少［3,9,10］,且仅限于对催化剂活性的研究. Haruta等［3］对Au/Fe2O3,Au/Co3O4和Au/TiO 2等体系开展了一些工作, 认为水对CO氧化活性有促进作用. 本文重点考察了水对MOx(M=Al,Ca,Co,Cr,Cu,Fe,La,Mn,Ni和Zn)催化剂上CO氧化活性的影响,以及水对Au/MOx 催化剂活性及稳定性的影响.     

α-Fe_2O_3-MgO复合氧化物的制备和气敏性能

用化学共沉淀法制备了 α-Fe2 O3-Mg O复合金属氧化物纳米晶微粉 .并对其相组成 ,电导和气敏性能作了研究 .结果表明 ,镁铁摩尔比 n(Mg2 )∶ n(Fe3 ) =1∶ 2、5 0 0℃下热处理 4h可得纯相尖晶石型复合金属氧化物 Mg Fe2 O4;电导测量显示 ,该材料呈 n型半导体导电行为 . 60 0℃下热处理 4h所得纳米晶微粉制作的元件在 2 2 7℃工作温度下对 C2 H5OH有较高灵敏度和良好的选择性 .     

Carbon Dioxide Reforming of Methane over Ni Catalysts Supported on Al2O3 Modified with La2O3, MgO, and CaO

The preparation of synthesis gas from carbon dioxide reforming of methane (CDR) has attracted increasing attention. The present review mainly focuses on CDR to produce synthesis gas over Ni/MO_x/Al₂O₃ (X = La, Mg, Ca) catalysts. From the examination of various supported nickel catalysts, the promotional effects of La₂O₃, MgO, and CaO have been found. The addition of promoters to Al₂O₃-supported nickel catalysts enhances the catalytic activity as well as stability. The catalytic performance is strongly dependent on the loading amount of promoters. For example, the highest CH₄ and CO₂ conversion were obtained when the ratios of metal M to Al were in the range of 0.04–0.06. In the case of Ni/La₂O₃/Al₂O₃ catalyst, the highest CH₄ conversion (96%) and CO₂ conversion (97%) was achieved with the catalyst (La/Al = 0.05 (atom/atom)). For Ni/CaO/Al₂O₃ catalyst, the catalyst with Ca/Al = 0.04 (atom/atom) exhibited the highest CH₄ conversion (91%) and CO₂ conversion (92%) among the catalysts with various CaO content. Also, Ni/MgO/Al₂O₃ catalyst with Mg/Al = 0.06 (atom/atom) showed the highest CH₄ conversion (89%) and CO₂ conversion (90%) among the catalysts with various Mg/Al ratios. Thus it is most likely that the optimal ratios of M to Al for the highest activities of the catalysts are related to the highly dispersed metal species. In addition, the improved catalytic performance of Al₂O₃-supported nickel catalysts promoted with metal oxides is due to the strong interaction between Ni and metal oxide, the stabilization of metal oxide on Al₂O₃ and the basic property of metal oxide to prevent carbon formation.     

助剂对Ni基催化剂结构及甲烷化性能的影响

本文采用等体积浸渍制备了掺杂不同金属助剂改性的Ni基催化剂,考察了其催化浆态床CO甲烷化的性能。通过XRD、H2-TPR、HR-TEM等表征对催化剂进行了分析,结果表明,掺杂Zr、Co、Ce、Zn、La助剂促进了Ni物种在载体表面的分散,减小了Ni的晶粒尺寸,降低了催化剂的还原温度;掺杂Mg助剂则导致催化剂的还原温度升高。浆态床活性评价结果表明,掺杂Zr、Co、Ce、Zn、La助剂提高了催化剂的甲烷化性能,其中以La助剂的效果最明显,通过对La负载量进一步优化后发现,当La负载量为8%时,催化剂的甲烷化催化性能最优,CO转化率、CH4选择性和时空收率分别达到96.3%、87.1%和179.6 g·kg-1·h-1;掺杂Mg助剂则降低了催化剂的甲烷化活性。     

助剂对Ni基催化剂结构及甲烷化性能的影响

本文采用等体积浸渍制备了掺杂不同金属助剂改性的Ni基催化剂,考察了其催化浆态床CO甲烷化的性能。通过XRD、H₂-TPR、HR-TEM等表征对催化剂进行了分析,结果表明,掺杂Zr、Co、Ce、Zn、La助剂促进了Ni物种在载体表面的分散,减小了Ni的晶粒尺寸,降低了催化剂的还原温度;掺杂Mg助剂则导致催化剂的还原温度升高。浆态床活性评价结果表明,掺杂Zr、Co、Ce、Zn、La助剂提高了催化剂的甲烷化性能,其中以La助剂的效果最明显,通过对La负载量进一步优化后发现,当La负载量为8%时,催化剂的甲烷化催化性能最优,CO转化率、CH₄选择性和时空收率分别达到96.3%、87.1%和179.6g·kg^-1·h^-1;掺杂Mg助剂则降低了催化剂的甲烷化活性。     

在Ni/HZSM-5催化剂上低温水蒸汽重整生物油制氢

We investigated high catalytic activity of Ni/HZSM-5 catalysts synthesized by the impregna-tion method, which was successfully applied for low-temperature steam reforming of bio-oil. The influences of the catalyst composition, reforming temperature and the molar ratio of steam to carbon fed on the stream reforming process of bio-oil over the Ni/HZSM-5 catalysts were investigated in the reforming reactor. The promoting effects of current passing through the catalyst on the bio-oil reforming were also studied using the electrochemical catalytic re-forming approach. By comparing Ni/HZSM-5 with commonly used Ni/Al₂O₃ catalysts, the Ni₂₀/ZSM catalyst with Ni-loading content of about 20% on the HZSM-5 support showed the highest catalytic activity. Even at 450 oC, the hydrogen yield of about 90% with a near complete conversion of bio-oil was obtained using the Ni₂₀/ZSM catalyst. It was found that the performance of the bio-oil reforming was remarkably enhanced by the HZSM-5 supporter and the current through the catalyst. The features of the Ni/HZSM-5 catalysts were also investigated via X-ray diffraction, inductively coupled plasma and atomic emission spectroscopy, hydrogen temperature-programmed reduction, and Brunauer-Emmett-Teller methods.     

助剂对Ni/SiO2催化剂微观结构及二硝基甲苯催化加氢性能的影响

采用等体积浸渍法制备了负载型Ni/SiO₂催化剂,研究了Ce、Zr、La、Co和Fe助剂对催化剂微观结构及其催化二硝基甲苯（DNT,C₆H₃CH₃（NO₂）₂）加氢制备甲苯二胺（TDA,C₆H₃CH₃（NH₂）₂）性能的影响。通过XRD,BET,H₂-TPD、H₂-TPR和XPS技术对催化剂进行了表征。结果表明,助剂的引入促进了Ni物种在载体表面的分散,减小了Ni晶粒的尺寸,使得NiO晶粒更易还原。添加La、Fe和Zr助剂增加了有效的Ni活性中心数,有利于催化活性的提高,其中,添加La助剂制备的催化剂催化性能最优,DNT转化率和TDA选择性分别为98.1%和99.1%。但Co和Ce助剂的加入降低了化学氢吸附量,使得有效的Ni活性中心数降低,降低了催化剂的催化活性。     

助剂对Ni/SiO_2催化剂微观结构及二硝基甲苯催化加氢性能的影响

采用等体积浸渍法制备了负载型Ni/SiO2催化剂,研究了Ce、Zr、La、Co和Fe助剂对催化剂微观结构及其催化二硝基甲苯(DNT,C6H3CH3(NO2)2)加氢制备甲苯二胺(TDA,C6H3CH3(NH2)2)性能的影响。通过XRD,BET,H2-TPD、H2-TPR和XPS技术对催化剂进行了表征。结果表明,助剂的引入促进了Ni物种在载体表面的分散,减小了Ni晶粒的尺寸,使得NiO晶粒更易还原。添加La、Fe和Zr助剂增加了有效的Ni活性中心数,有利于催化活性的提高,其中,添加La助剂制备的催化剂催化性能最优,DNT转化率和TDA选择性分别为98.1%和99.1%。但Co和Ce助剂的加入降低了化学氢吸附量,使得有效的Ni活性中心数降低,降低了催化剂的催化活性。     

The catalytic performance of different promoted iron catalysts on combined supports Al<Subscript>2</Subscript>O<Subscript>3</Subscript> for carbon dioxide hydrogenation

Global warming, fossil fuel depletion and fuel price increases have motivated scientists to search for methods for the storage and reduction of the amount of greenhouse gases, especially CO₂. The hydrogenation process has been introduced as an emerging method of CO₂ capture and convertion into value-added products. In this study, new types of catalysts are introduced for CO₂ hydrogenation and are compared based on catalytic activity and product selectivity. The physical properties of the samples are specified using BET. Iron catalysts supported on γ-Al₂O₃ with different metal promoters (X = Ni, K, Mn, Cu) are prepared through the impregnation method. Moreover, Fe–Ni catalysts supported on HZSM5-Al₂O₃ and Ce–Al₂O₃ are synthesized. Samples are reduced by pure H₂ and involved in hydrogenation reaction in a fixed bed reactor (H₂/CO₂ = 3, total pressure = 10 MPa, temperature = 523 K, GHSV = 2000, 1250 nml/min). All catalysts provide high conversion in hydrogenation reactions and the results illustrate that the selectivity of light hydrocarbons is higher than that of methane and CO. It is found that Ni has a promoting effect on the conversion fluctuations throughout the reaction with 66.13% conversion. Using combined supported catalysts leads to enhancing catalytic performance. When Fe–Ni/γ–Al₂O₃—HZSM5 is utilized, CO₂ conversion is 81.66% and the stability of the Fe–Ni catalyst supported on Al₂O₃ and Ce–Al₂O₃ furthey improves.     

Promotion effect of additive Fe on Al2O3 supported Ni catalyst for CO2 methanation

In this paper, the effect of additive Fe on Ni/Al₂O₃ catalyst for CO₂ methanation was studied. A series of bimetallic Ni–Fe catalysts with different Ni/Fe ratios were prepared by impregnation method. For comparison, monometallic Fe‐based and Ni‐based catalysts were also prepared by the same method. The characterization results showed that adding Fe to Ni catalyst on the premise of a low Ni loading(≦12 wt.%) enhanced CO₂ methanation performance. However, when the Ni loading reached 12 wt.%, the catalytic activity decreased with the increase of Fe content, but still higher than the corresponding Ni‐based catalyst without Fe. Among them, the 12Ni3Fe catalyst exhibited the highest CO₂ conversion of 84.3 % and nearly 100% CH₄ selectivity at 50000 ml g^‐1 h^‐1 and 420 °C. The enhancement effect of adding Fe on CO₂ methanation was attributed to the dual effect of suitable electronic environment and increased reducibility generated by Fe species.     

Autothermal Reforming of Methane over Ni Catalysts Supported on CuO-ZrO2-CeO2-Al2O3

Ni catalysts supported on various mixed oxides of Al2O3 with rare earth oxide and transitional metal oxides were synthesized. The studies focused on the measurement of the autothermal reforming of methane to hydrogen over Ni catalysts supported on the mixed oxide ZrxCe30-xAl70Oδ (x=5, 10, 15). The catalytic performance of Ni/Zr10Ce20Al70Oδ was better than that of other catalysts. XRD results showed that the addition of Zr to Ni/Ce30Al70Oδ prevented the formation of NiAl2O4 and facilitated the dispersion of NiO. Effects of CuO addition to Zr10Ce20Al70Oδ were also investigated. The activity of Ni catalyst supported on CuO-ZrO2-CeO2-Al2O3 was somewhat affected and the Ni/Cu5Zr10Ce20Al65Oδ showed the best catalytic performance with the highest CH4 conversion, yield of H2, selectivity for H2 and H2/CO production ratio in operation temperatures ranging from 650 to 750℃.     

Influence of Metallic Modification on Ethylbenzene Dealkylation over ZSM‐5 Zeolites

A series of metal‐modified HZSM‐5 catalysts were prepared by impregnation and were used for ethylbenzene dealkylation of the mixed C8 aromatics (ethylbenzene, m‐xylene and o‐xylene). The effects of different supported metals (Pt, Pd, Ni, Mo) on catalytic performance, including reaction conditions, were investigated. The physicochemical properties of catalysts were characterized by means of XRD, BET, TEM and NH₃‐TPD. Experimental results showed that metallic modification obviously increased the ethylbenzene conversion and reduced the coke deposition, greatly improving the catalyst stability. The distinction of ethylbenzene conversion depended on the interaction between hydrogenation reactivity and acidic cracking of bifunctional metal‐modified zeolites. Compared with Pt and Ni, Pd and Mo were easier to disperse into HZSM‐5 micropores during loading metals. The acidic density of different metal‐modified HZSM‐5 declined in the following order: HZSM‐5>Pt/HZSM‐5>Pd/HZSM‐5>Ni/HZSM‐5>Mo/HZSM‐5. The activity of ethylene hydrogenation decreased with Pt/HZSM‐5>Pd/HZSM‐5>Ni/HZSM‐5>Mo/HZSM‐5. In comparison, Pd/HZSM‐5 showed the best catalytic performance with both high activity and high selectivity, with less cracking loss of m‐xylene and o‐xylene. Moreover, the following reaction conditions were found to be preferable for ethylbenzene dealkylation over Pd/HZSM‐5: 340°C, 1.5 MPa H₂, WHSV 4 h^?1, H₂/C8 4 mol/mol.