Fe—Zn—M／HZSM—5复合催化剂上CO2加氢性能的研究

研究了380℃、5.0MPa条件下,在Fe-Zn-M/HZSM-5(M=Cr、Al）复合催化剂上进行的CO2催化加氢的反应,考察了Fe-Zn-M中Fe含量、分子筛的硅铝比及Fe-Zn-M/HZSM-5的比率对CO2转化率和产物选择性的影响。结果表明,随着Fe含量的增加,复合催化剂的活性增强、目的产物选择性降低;Fe-Zn-M与HZSM－5间有适宜的配比;分子筛的硅铝比影响到复合催化剂的活性和选择性,随着分子筛硅铝比的降低,复合催化剂的活性增强,目的产物选择性提高。     

Effects of silicon to aluminum ratio and crystal size of zeolite on catalytic properties of Cu-ZnO-Al2O3/HZSM-5 for the direct synthesis of dimethyl ether from syngas

采用水热晶化法合成了硅铝比(SiO2/Al2O3)为60、120、200和晶粒粒径分别为1.00和0.25μm的HZSM-5分子筛,并以其为甲醇脱水活性组分与铜基甲醇合成活性组分(Cu-ZnO-Al2O3)组成双功能催化剂(Cu-ZnO-Al2O3/HZSM-5),在连续流动加压固定床反应器上考察了Cu-ZnO-Al2O3/HZSM-5对合成气直接制二甲醚反应的催化性能.结果表明,随着分子筛硅铝比的提高,二氧化碳副产物的生成量逐渐减少,从而使目的产物二甲醚的选择性逐渐增大.与常规分子筛相比,小晶粒分子筛的反应活性接近,但二氧化碳和烃类副产物的选择性较低.     

Cu-Pd/MCM-22催化剂上二甲醚低温水解反应

 考察了分子筛的类型、硅铝比及Cu和Pd改性对分子筛催化剂上二甲醚低温水解活性的影响. 结果表明,酸性的MCM-22和HZSM-5分子筛催化剂具有较高的二甲醚水解活性,且其活性随着分子筛硅铝比的增加而降低. 这表明分子筛的类型及酸性对催化剂性能有重要影响,具有超笼结构的MCM-22分子筛上B酸中心的良好可接近性,使得该分子筛催化剂的水解活性较相同硅铝比的HZSM-5分子筛高. 与改性前相比, Cu和Pd改性后的MCM-22催化剂显示出更高的二甲醚水解活性.     

ZnCrO_x/HZSM-5催化合成气直接转化制异构烷烃

分别采用共沉淀法和水热法制备了ZnCrO_x复合金属氧化物和HZSM-5沸石,通过物理混合得到双功能催化剂,实现了合成气一步高选择性制备异构烷烃。采用XRD、TEM、氮吸附和NH3-TPD等技术对催化剂进行了表征,考察了双功能催化剂中HZSM-5沸石组分硅铝比以及ZnCrO_x/HZSM-5质量比(OX/ZEO mass ratio)对合成气催化转化反应性能的影响。结果表明,随着HZSM-5硅铝比的增加,催化剂酸密度下降,CO转化率略有下降,产物中C5+选择性显著提高,异构烷烃比例不断增加。此外,在保证CO转化率的前提下提高双功能催化剂中ZnCrO_x组分的比例,产物中C5+的选择性也显著上升。在400℃、2.0 M Pa、进料空速(GHSV)为3600 mL/(h·gcat)的条件下,合成气(H2/CO(volume ratio)=2)转化率达到35%,C5+选择性超过44%,且C5+中异戊烷比例高达65%。     

Fe含量对Fe-Zn-M/HY复合催化剂上CO2加氢性能的影响

在340 ℃，5.0 MPa条件下，研究了Fe-Zn-M/HY(M=Cr、Al)复合催化剂上CO2的加氢性能。考察了催化剂中Fe含量对CO2转化率、烃类产物及异构烷烃选择性的影响, 并用CO2-TPD、H2-TPR研究了Fe-Zn-M对CO2的吸附和对H2的还原性能。结果表明, 随着Fe含量的增加, 复合催化剂的活性增强, 烃类产物的选择性降低, 异构烷烃在烃类中的选择性随Fe含量的增加而降低，CO2-TPD、H2-TPR结果表明，随Fe含量的增加，催化剂对CO2的活化吸附量随之增加, 而Fe含量的增加促进了催化剂的还原。     

分子筛硅铝比及晶粒粒径对 Cu-ZnO-Al2O3/HZSM-5催化剂直接合成二甲醚反应性能的影响

采用水热晶化法合成了硅铝比(SiO₂/Al₂O₃)为60、120、200和晶粒粒径分别为1.00和0.25 μm的HZSM-5分子筛,并以其为甲醇脱水活性组分与铜基甲醇合成活性组分(Cu-ZnO-Al₂O₃)组成双功能催化剂(Cu-ZnO-Al₂O₃/HZSM-5),在连续流动加压固定床反应器上考察了Cu-ZnO-Al₂O₃/HZSM-5对合成气直接制二甲醚反应的催化性能。结果表明,随着分子筛硅铝比的提高,二氧化碳副产物的生成量逐渐减少,从而使目的产物二甲醚的选择性逐渐增大。与常规分子筛相比,小晶粒分子筛的反应活性接近,但二氧化碳和烃类副产物的选择性较低。     

用TPD法研究不同硅铝比的HZSM-5分子筛的酸性质及其催化能

本文用动态程序升温热脱附法研究了不同硅铝比的HZSM-5分子筛吸附氨的程序升温热脱附谱及其酸性质。结果表明,当硅铝比的效值小子47时,HZSM-5分子筛吸附氨的酸中心数与单跑中铝原子效呈线性递增关系。当硅铝比大于47时,则偏离了该线性关系。不同硅铝比的HZSM-5分子筛的酸强度随着硅铝比的下降而增强,它们的甲苯歧化活性与其单胞中铝原子数亦有线性递增关系,随着铝原子数的增加,催化活性提高,而选择性下降。     

Pt/HZSM-5基催化剂双功能协同性对正丁烷催化裂解反应机制的影响

轻质烷烃结构稳定,化工利用率低.催化裂解轻质烷烃是其高值利用的重要途径,相关研究同时对C-C键和C-H键活化和演变调控具有重要意义.本文在基于原子层沉积法构建高稳定Pt/HZSM-5基双功能模型催化剂的基础上,研究了不同酸性HZSM-5分子筛引入脱氢组分Pt对反应路径及目的产物低碳烯烃的影响规律.研究发现,双功能催化剂中, Pt的脱氢性能与分子筛的酸性裂解性能存在协同作用,不同硅铝比的分子筛上引入Pt,高硅铝比分子筛上Pt的引入对脱氢促进效应更明显.同时,将脱氢组分Pt引入到不同裂解能力的酸性分子筛载体上,会改变其低碳烯烃的生成路径,高硅铝比的分子筛上引入Pt后丁烯的生成路径增强,而低硅铝比的分子筛上则会增强乙烯与丙烯的生成路径,当分子筛硅铝比继续降低时,乙烯的生成路径进一步增强.本研究对多相复杂反应中反应路径调控及高效双功能催化剂设计具有指导意义.     

不同硅铝比HZSM-5分子筛对煤热解挥发物催化提质的影响

采用不同硅铝比的HZSM-5作为煤热解挥发物提质催化剂,研究了催化剂酸性特征对挥发物提质后的焦油品质、催化剂积炭的影响。结果表明,随着硅铝比的增加,HZSM-5的强酸和弱酸量均降低;硅铝比从23增大到310时,催化剂积炭量从120.1 mg/g-catalyst降到23.9 mg/g-catalyst。并且,HZSM-5中强酸与弱酸位点的比值越高,焦油中轻质组分的含量越高。随硅铝比的降低,HZSM-5酸性增强,所得焦油中芳烃组分含量逐渐提高,这表明,HZSM-5在催化煤热解过程中促进了挥发物的氢转移、环化、芳构化反应,从而生成了更多的芳烃组分。     

丁烯-2在HZSM-5分子筛上的齐聚反应

在温度为210~300℃、压力为3~5 MPa、LHSV为0.5~1.5 h-1的条件下,用连续固定床反应器,考察了丁烯-2在HZSM-5上的齐聚反应.结果表明:丁烯-2在HZSM-5分子筛上的反应类型和产物中高碳烯烃的含量与温度、压力及空速有关.反应温度在300℃以下,反应产物主要是烯烃,其结构显示择形催化的特点.HZSM-5分子筛的酸性对齐聚反应的活性和选择性有一定影响,低硅铝比的HZSM-5有较高的活性和高碳烯烃的选择性.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.