No-Glycerol rapid heterogeneous biodiesel production on K<Subscript>2</Subscript>CO<Subscript>3</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst by coupling process

Biodiesel containing almost no glycerol has been produced by coupling reaction carried out over K₂CO₃ supported by calcium oxide as solid base catalysts. The solid base catalysts synthesized by wet impregnation exhibit an exceedingly high activity in biodiesel production. It was found that the reaction time required for the highest yield of biodiesel, 99.2%, can be shortened to 30 min over K₂CO₃/Al₂O₃ under the optimum reaction conditions: 8: 1: 1 molar ratio of methanol/DMC/oil, 30 wt % K₂CO₃/Al₂O₃ catalyst, and 65°C reaction temperature. Solid basic catalysts examined in the study were characterized by BET surface area, XRD, CO₂-TPD, and SEM techniques. The strong interaction between K₂CO₃ and the support yields a new basic active site, which can be probably responsible for the high activity of K₂CO₃/Al₂O₃.     

Monolithic FeO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for ammonia oxidation and nitrous oxide decomposition

(1.2–8.3)%FeO_х/Al₂O₃ monolith catalysts have been prepared by impregnating alumina with aqueous solutions of iron(III) nitrate and oxalate and have been tested in NH₃ oxidation and in the selective decomposition of N₂O in mixtures resulting from ammonia oxidation over a Pt–Rh gauze pack under conditions of nitric acid synthesis (800–900°C). In the case of the support calcined at 1200°C, the catalyst is dominated by bulk Fe₂O₃ particles localized on the Al₂O₃ surface. The activity of these samples in both reactions decreases with a decreasing active component content, thus limiting the potential of Fe₂(C₂O₄)₃ · 5H₂O, an environmentally friendlier but poorly soluble compound, as a substitute for Fe(NO₃)₃ · 9H₂O. Decreasing the support calcination temperature to 1000°C or below leads to the formation of a highly defective Fe–Al–O solid solution in the (1.2–2.7)%FeO_х/Al₂O₃ catalysts. The surface layers of the solid solution are enriched with iron ions or stabilize ultrafine FeO_х particles. The catalytic activity of these samples in both reactions is close to the activities measured for ~8%FeO_х/Al₂O₃ samples prepared using iron nitrate.     

Preparation and performance of potassium-based sorbent using SnO<Subscript>2</Subscript> for post-combustion CO<Subscript>2</Subscript> capture

Potassium-based sorbents using γ-Al₂O₃ or TiO₂ as a support or an additive material have disadvantages in terms of their thermal stability and cyclic CO₂ capture. To overcome the shortcomings of these sorbents, a novel potassium-based sorbent (KSnI30) using SnO₂ was developed in this study. The KSnI30 sorbent formed only K₂CO₃ and SnO₂ phases without any inactive alloy species even after calcination at high temperatures (500–700 °C), indicating the good thermal stability of the KSnI30 sorbent regardless of the calcination temperature. Furthermore, the KSnI30 sorbent has an excellent regeneration property (above 98 %), as well as high CO₂ capture capacities (89–94 mg CO₂/g sorbent). Its excellent regeneration property is due to the formation of a KHCO₃ phase without by-products during CO₂ sorption. These results of the present study demonstrate that the SnO₂ shows promise as a new support or an additive material to replace TiO₂ and γ-Al₂O₃ in the preparation of a regenerable potassium-based sorbent for post-combustion CO₂ capture with good thermal stability and excellent regeneration property.     

Hydrogenolysis of glycerol to propanediols over heteropolyacids promoted AgCu/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

Various amounts and different types of heteropolyacids promoted 5Ag15Cu/Al₂O₃ catalysts were prepared by impregnation method and analyzed through many techniques. The synthesized catalysts were evaluated for hydrogenolysis of glycerol to propanediols. The results demonstrated that heteropolyacids loading facilitated the reduction, promoted the dispersion, enhanced the acidity, and increased Broensted acid sites of the AgCu catalysts, which benefited the generation of 1,3-propanediol. Compared with phosphotungstic acid and phosphomolybdic acid, silicotungstic acid promoted AgCu catalyst had a better performance for 1,3-propanediol due to the better Cu dispersion and higher Broensted acidity. In addition, when the reaction was performed at 220 °C under 3.5 MPa for 8 h, the chosen 5Ag15Cu-10HSiW/Al₂O₃ achieved a 69.6% glycerol conversion with 35.6% 1,2-propanediol selectivity and 21.5% 1,3-propanediol selectivity.     

Promoted porous Co<Subscript>3</Subscript>O<Subscript>4</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts for ammonia decomposition

Transition metal catalysts have been considerably used for NH₃ decomposition because of the potential application in CO_x-free H₂ generation for fuel cells. However, most transition metal catalysts prepared via traditional synthetic approaches performed the inferior stability due to the agglomeration of active components. Here, we adopted an efficient method, aerosol-assisted self-assembly approach (AASA), to prepare the optimized cobalt-alumina (Co₃O₄-Al₂O₃) catalysts. The Co₃O₄-Al₂O₃ catalysts exhibited excellent catalytic performance in the NH3 decomposition reaction, which can reach 100% conversion at 600 °C and maintain stable for 72 h at a gaseous hourly space velocity (GHSV) of 18000 cm³ g_cat^?1 h^?1. The catalysts were characterized by various techniques including transmission electron microscope (TEM), scanning electron microscope (SEM), nitrogen sorption, temperature-programmed reduction by hydrogen (H₂-TPR), ex-situ/in-situ Raman and ex-situ/in-situ X-ray diffraction (XRD) to obtain the information about the structure and property of the catalysts. H₂-TPR and in-situ XRD results show that there is strong interaction between the cobalt and alumina species, which influences the redox properties of the catalysts. It is found that even a low content of alumina (10 at%) is able to stabilize the catalysts due to the adequate dispersion and rational interaction between different components, which ensures the high activity and superior stability of the cobalt-alumina catalysts.     

Co-Mo/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and Ni-W/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts: Potential and prospects for use in hydrotreating of light cycle oil from catalytic cracking

Со-Мо/Al₂O₃ and Ni-W/Al₂O₃ catalysts were tested in hydrotreating of light cycle oil from catalytic cracking, of the straight-run gasoil, and of their mixture under typical hydrotreating conditions used in industry. The catalysts prepared using PMo₁₂ and PW₁₂ heteropoly acids exhibit high catalytic activity. The Со-Мо/Al₂O₃ catalyst is more active in hydrodesulfurization and hydrogenation of olefin and diene hydrocarbons, whereas the Ni-W/Al₂O₃ catalysts are more active in hydrogenation of mono- and polycyclic aromatic hydrocarbons. Comparison of the quality characteristics of the hydrogenizates obtained with the requirements of the technical regulations shows that the required levels of the sulfur content and cetane number of the hydrogenizates at practically accessible process parameters can be reached for mixtures of the straight-run gasoil and light cycle oil from catalytic cracking with high content of the latter component only when the process with the Со-Мо/Al₂O₃ system and Ni-W/Al₂O₃ catalysts is performed in two steps.     

Preparation and characterization of H<Subscript>3</Subscript>PW<Subscript>12</Subscript>O<Subscript>40</Subscript>/ZrO<Subscript>2</Subscript> catalyst for carbonation of methanol into dimethyl carbonate

A H₃PW₁₂O₄₀/ZrO₂ catalyst for effective dimethyl carbonate (DMC) formation via methanol carbonation was prepared using the sol–gel method. X-ray photoelectron spectra showed that reactive and dominant (63%) W(VI) species, in WO₃ or H₂WO₄, enhanced the catalytic performances of the supported ZrO₂. The mesoporous structure of H₃PW₁₂O₄₀/ZrO₂ was identified by nitrogen adsorption–desorption isotherms. In particular, partial sintering of catalyst particles in the duration of methanol carbonation caused a decrease in the Brunauer–Emmett–Teller surface area of the catalyst from 39 to 19 m²/g. The strong acidity of H₃PW₁₂O₄₀/ZrO₂ was confirmed by the desorption peak observed at 415 °C in NH₃ temperature-programmed desorption curve. At various reaction temperatures (T?=?110, 170, and 220 °C) and CO₂/N₂ volumetric flow rate ratios (CO₂/N₂?=?1/4, 1/7, and 1/9), the calculated catalytic performances showed that the optimal methanol conversion, DMC selectivity, and DMC yield were 4.45, 89.93, and 4.00%, respectively, when T?=?170 °C and CO₂/N₂?=?1/7. Furthermore, linear regression of the pseudo-first-order model and Arrhenius equation deduced the optimal rate constant (4.24?×?10^?3 min^?1) and activation energy (E_a?=?15.54 kJ/mol) at 170 °C with CO₂/N₂?=?1/7 which were favorable for DMC formation.     

Chemo-bio catalyzed synthesis of <Emphasis Type="Italic">R</Emphasis>-1-phenylethyl acetate over bimetallic PdZn catalysts,lipase, and Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>. part I

One-pot synthesis of R-1-phenyethylacetate at 70°C was investigated using three different catalysts simultaneously, namely a bimetallic PdZn/Al₂O₃ as a hydrogenation catalyst, an immobilized lipase as an acylation catalyst and Ru/Al₂O₃ as a racemization catalyst. The most active bimetallic catalyst was PdZn/Al₂O₃ calcined at 300°C and reduced at 400°C, whereas the most selective although less active catalyst was the one being calcined and reduced at 500°C. The highest selectivity to R-1-phenylethyl acetate over this catalyst was 32 at 48% conversion. Ru/Al₂O₃ was confirmed to have a positive effect on the formation of the desired product, although it was not very active in the racemization during one-pot synthesis.     

Oxidative conversion of methane and methanol on M/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/cordierite structured metal oxide catalysts (m = Ni,Cu, Zn)

A study was carried out on the properties of Ni/Al₂O₃ and Cu-ZnO/Al₂O₃ composites supported on ceramic honeycomb monoliths made from synthetic cordierite in the carbon dioxide conversion of methane and the partial oxidation of methanol. The structured nickel-alumina catalysts are significantly more efficient than the conventional granulated catalysts. The improved working stability of these catalysts was achieved by adjusting the acid-base properties of the surface by introducing sodium and potassium oxides, which leads to inhibition of surface carbonization. The hydrogen yield was close to 90% in the partial oxidation of methanol with a stoichiometric reagent ratio in the presence of the Cu-ZnO/Al₂O₃/cordierite catalyst. A synergistic effect was found, reducing the selectivity of CO formation in the presence of the Cu-ZnO catalyst relative to samples derived from the individual components Cu and ZnO. __________ Translated from Teoreticheskaya i éksperimental’naya Khimiya, Vol. 43, No. 5, pp. 299–306, September–October, 2007.     

Hydrogenation of aromatic hydrocarbons in a mixture with thiophene on sulfided Pd/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalysts

The activity and stability of aluminum-palladium catalysts in the hydrogenation of aromatic hydrocarbons mixed with thiophene were studied. The catalysts were obtained by impregnation of γ-A₂O₃ with aqueous solutions of salts of palladium complexes. Preliminary sulfiding followed by oxidative activation of Pd/Al₂O₃ catalysts were found to favor the formation of such palladium state on the surface at which the hydrogenation of aromatic hydrocarbons in the presence of sulfur-containing impurities proceeds without a noticeable change in the activity with time. IR spectroscopy showed that the palladium metal surface fragments forming CO complexes with a characteristic absorption band at 1998 cm^–1 are resistant to poisoning with sulfur-containing compounds in the hydrogenation of aromatic hydrocarbons.     

Nano-Architecture of Facetted NiFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/(Ni,Fe)O Particles Produced by Induction Plasma

Facetted nickel ferrite (NiFe₂O₄) and bunsenite [(Ni,Fe)O] nanocrystals were grown from the decomposition of iron and nickel nitrate precursors using an inductively coupled plasma reactor. The full range of the two-phase region of the Fe₂O₃–NiO pseudo-equilibrium phase diagram was investigated by producing nanopowders with bulk Ni/(Ni + Fe) ratios of 0.33, 0.4, 0.5, 0.75 and 1.0. A Ni-poor [Ni/(Ni + Fe) ≤ 0.5] precursor solution produced truncated octahedron nanocrystals, whereas nanocubes were obtained at higher ratios [Ni/(Ni + Fe) ≈ 1]. In both cases, it is shown that the nanocrystals adopt a morphology close to the Wulff shape of the crystalline system (spinel and NaCl, respectively). As the bulk Ni/(Ni + Fe) ratio increases from 0.33 (the stoechiometric composition of nickel ferrite), bunsenite is epitaxially segregated on the {110} and {111} facets of nickel ferrite, while leaving the NiFe₂O₄ {100} facets exposed. A precursor solution at a Ni/(Ni + Fe) ratio of 0.75 gave an (Ni,Fe)O-rich nanopowder with a random and irregular interconnected morphology. The structure of these nanocrystals can be understood in terms of their thermal history in the plasma reactor. These results highlights the possibility of producing organized multi-phased nanomaterials of binary systems having two phases stable at high temperatures, using a method known to be easily scalable.     

Chemo-bio catalyzed synthesis of <Emphasis Type="Italic">R</Emphasis>-1-phenylethyl acetate over bimetallic PdZn catalysts,lipase, and Ru/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>. Part II

One-pot synthesis of R-1-phenyethylacetate at 70°C was investigated using three different catalysts simultaneously, namely a bimetallic PdZn/Al₂O₃ as a hydrogenation catalyst, an immobilized lipase as an acylation catalyst and Ru/Al₂O₃ as a racemization catalyst. The most active bimetallic catalyst was PdZn/Al₂O₃ calcined at 300°C and reduced at 400°C, whereas the most selective although less active catalyst was the one being calcined and reduced at 500°C. The highest selectivity to R-1-phenylethyl acetate over this catalyst was 32 at 48% conversion. Ru/Al₂O₃ was confirmed to have a positive effect on the formation of the desired product, although it was not very active in the racemization during one-pot synthesis.     

Oxidative dehydrogenation of propane on the VO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/CeZrO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> supported catalyst

The oxidative dehydrogenation of propane on a supported vanadium catalyst was studied (the support was a complex oxide system consisting of a ceria–zirconia solid solution deposited on γ-Al₂O₃ (CeZrO/γ-Al₂O₃)). A comparative analysis of the properties of the support and the catalyst prepared on its basis was performed. The support and catalyst were characterized by the BET method, scanning electron microscopy, X-ray diffraction analysis, and Raman spectroscopy. The catalytic properties of the catalyst and support were studied in propane oxidation at 450 and 500°C with pulse feeding of the reagent. The effect of propane on the support was found to improve the oxidative properties of the latter. This behavior of the support is related to the preparation procedure, which leads to the formation on its surface of the crystalline phase of the ceria–zirconia solid solution and amorphous ZrO₂ and Al₂O₃ phases and/or their solid solution. Similar processes occur with the catalyst support during the oxidative dehydrogenation, giving rise to additional active centers (CeVO₄).     

ZrO<Subscript>2</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> binary oxides as promising supports for palladium catalysts of hydrodechlorination

Deposited palladium catalysts of the hydrodechlorination of 1,3,5-trichlorobenzene were studied. Pure zirconium and aluminum oxides and ZrO₂-Al₂O₃ mixtures with 1, 5, and 10 mol % Al₂O₃ prepared by coprecipitation were used as supports. Palladium was deposited by the precipitation of its hydroxide on supports. Catalysts on binary supports (ZrO₂ + 1% Al₂O₃ and ZrO₂ + 5% Al₂O₃) exhibited higher activity and stability in hydrodechlorination compared with catalysts on pure supports. The suggestion was made that the high activity and stability of these systems in hydrodechlorination was related to the formation of binary oxide in the interaction of ZrO₂ with palladium oxide at the stage of annealing of the catalyst precursor. Binary oxide, which was a center of the activation of the C-Cl bond, was simultaneously a source of active hydrogen. The presence of various palladium states in catalysts was substantiated by the temperature programmed reduction method.     

Catalytic amination of 2,6-dimethylphenol to 2,6-dimethylaniline over Ni–Cu–Cr/γ-Al2O3

A series of transition metal-based catalysts, other than Pd or Pt-based catalysts, were investigated for catalytic amination of 2,6-dimethylphenol to 2,6-dimethylaniline in a fixed-bed reactor. Ni–Cu–Cr/γ-Al₂O₃ yielded satisfactory results with 82.08 % conversion and 47.24 % selectivity. The catalysts were characterized by H₂-TPR and TEM, and the results obtained showed that the doped Cu and Cr could promote reduction of Ni/γ–Al₂O₃ and dispersion of the Ni. Reaction conditions, including reaction temperature, flow rate of hydrogen, and ammonia, were studied.     

High-Efficient Conversion of CO<Subscript>2</Subscript> in AC-Pulsed Tornado Gliding Arc Plasma

An AC-pulsed tornado gliding arc plasma was employed for CO₂ conversion via CO₂ decomposition and dry reforming reactions. A stable and high-efficient constant arc length discharge mode was obtained in this plasma reactor. And then, CO₂ conversion was studied under this discharge mode. In the case of CH₄/CO₂ = 0, CO₂ was converted to CO and O₂ via the CO₂ decomposition reaction. Energy efficiency of 29 % was attained at CO₂ conversion of 6 %. With strong reducing agent CH₄ added into CO₂, the main contributor of CO₂ conversion changed from CO₂ decomposition to dry reforming of CH₄. Conversions of CH₄ and CO₂, energy efficiency and energy cost changed sharply at CO₂/CH₄ ratios lower than 1/4, while they changed slowly at CH₄/CO₂ ratios above 1/4. In the case of CH₄/CO₂ = 2/3, energy efficiency of 68 % and syngas energy cost of 1.6 eV/mole were achieved at CH₄ conversion of 29 % and CO₂ conversion of 22 %.     

The effect of spinel type support FeAlO<Subscript>3</Subscript>, ZnAl<Subscript>2</Subscript>O<Subscript>4</Subscript>, CrAl<Subscript>3</Subscript>O<Subscript>6</Subscript> on physicochemical properties of Cu,Ag, Au,Ru supported catalysts for methanol synthesis

The comparative study of the role of binary oxide support on catalyst physico-chemical properties and performance in methanol synthesis were undertaken and the spinel like type structures (ZnAl₂O₄, FeAlO₃, CrAl₃O₆) were prepared and used as the supports for 5% metal (Cu, Ag, Au, Ru) dispersed catalysts. The monometallic 5% Cu/support and bimetallic 1% Au (or 1% Ru)-5% Cu/support (Al₂O₃, ZnAl₂O₄, FeAlO₃, CrAl₃O₆) catalysts were investigated by BET, XRD and TPR methods. Activity tests in methanol synthesis of CO and CO₂ mixture hydrogenation were carried out. The order of Cu/support catalysts activity in methanol synthesis: CrAl₃O{ia6} > FeAlO₃ > ZnAl₂O₄ is conditioned by their reducibility in hydrogen at low temperature. Gold appeared more efficient than ruthenium in promotion of Cu/support catalysts. Published in Russian in Kinetika i Kataliz, 2009, Vol. 50, No. 2, pp. 242–248. The article is published in the original.     

Studies on the synthesis of higher alcohol over modified Cu/ZnO/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst

Higher alcohol has been considered as a potential fuel additive. Higher alcohol, including C₂–C₄ alcohol was synthesized by catalytic conversion of syngas (with a ratio of CO/H₂?=?1) derived from natural gas over modified Cu/ZnO/Al₂O₃ catalyst. Modified Cu/ZnO/Al₂O₃ catalysts promoted by alkali metal (Li) for higher alcohol synthesis (HAS) were prepared at different pH (6, 6.5, 7, 8, and 9) by co-precipitation to control Cu surface area and characterized by N₂ physisorption, XRD, SEM, H₂-TPR and TPD. The HAS reaction was carried out under a pressure of 45 bar, GHSV of 4000 h^?1, ratio of H₂/CO?=?1, and temperature ranges of 240 and 280 °C. It was found that the malachite phase of copper causes the size of copper to be small, which is suitable for methanol synthesis. Methanol and HAS share a common catalytic active site and intermediate. It was also found that the productivity to higher alcohol was correlated with Cu surface area.     

Electrochemical Characterisations of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>–13%TiO<Subscript>2</Subscript> Coated by Atmospheric Plasma Spray

Atmospheric plasma sprayed alumina–titania (Al₂O₃–13%TiO₂), coated on stainless steel (XC18), were characterized. The coating structure and morphology were studied by scanning electron microscopy. Their presented micro cracks, laminar splats. The coatings were studied by X-ray diffraction. The main phase transformation is that of α-Al₂O₃ into metastable γ-Al₂O₃. The α-Al₂O₃ phase is due to the occurrence of partially melted particles Electrochemical behaviours of coatings were mainly investigated by potentiodynamic polarization and electrochemical impedance spectroscopy in 0.01 M [K₃Fe(CN)₆/K₄Fe(CN)₆] as a function of process parameters. Also, schematic equivalent circuit was proposed. The results were expected to facilitate the understanding and improvement of the coating behaviours.     

Effect of the Support on the Nature of Metal-Promoter Interactions in Ru-Cs<Superscript>+</Superscript>/MgO and Ru-Cs<Superscript>+</Superscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> Catalysts for Ammonia Synthesis

The Ru-Cs⁺/MgO and Ru-Cs⁺/γ-Al₂O₃ catalysts, which were prepared by an impregnation method using RuOHCl₃ and Cs₂CO₃ as precursor compounds and reduced with H₂ at 450°C, are characterized by X-ray diffraction, high-resolution transmission electron microscopy (with X-ray microanalysis), and X-ray photoelectron spectroscopy (XPS). The Cs⁺/MgO(Al₂O₃) systems, Ru-Cs⁺ black, and model systems prepared by cesium sputtering onto polycrystalline ruthenium foil are studied as reference samples. It is found that, in the Ru-Cs⁺/MgO sample, cesium is present as a Cs_{2 + x}O cesium suboxide, which weakly interacts with the support, localized on the surface of Ru particles or near them. In the case of Ru-Cs⁺/γ-Al₂O₃, cesium occurs as a species that is tightly bound to the support; this is likely surface cesium aluminate, which prevents promoter migration to Ru particles. The Ru-Cs⁺/MgO sample exhibits a considerable shift of the Ru3d line in the XPS spectra toward lower binding energies, as compared to the bulk metal. It is hypothesized that this shift is due to a decrease in the electron work function from the surface of ruthenium because of the polarizing effect of Cs⁺ ions in contact with Ru particles. Based on the experimental results, the great difference between the catalytic activities of the Ru-Cs⁺/MgO and Ru-Cs⁺/γ-Al₂O₃ systems in ammonia synthesis at 250–400°C and atmospheric pressure is explained.