含空间位阻侧链取代炔烃的合成及其催化聚合

设计并合成了具有较大空间位阻侧链的取代炔烃2-炔丙氧基-1,4-对苯二甲酸二甲酯单体,分别采用WCl6,WCl6-SnPh4和[Rh(nbd)Cl]2催化体系使其聚合,考察了不同催化剂对聚合的影响.采用红外光谱和核磁共振等技术对单体及聚合物结构进行了表征,并用紫外光谱和荧光光谱研究了所得聚合物的光学性能.结果表明,使用[Rh(nbd)Cl]2催化剂时得到的聚合物是高反式结构,荧光光谱中除了侧基的350 nm发射峰外,还在429 nm处存在较弱的共轭主链发射.使用WCl6-SnPh4催化体系得到的聚合物由于较高的顺式含量,主要是侧基的发射,而较大侧基位阻使主链共轭降低.尽管存在较短的间隔基,引入较大空间位阻侧基仍然迫使聚合物主链扭曲,顺式结构中侧基空间位阻的影响更大.     

1,4-丁炔二醇的均聚及与苯乙炔的共聚研究

<正> 炔类聚合物由于具有长链π体系的结构特点,理论上可作为结构型导电聚合物,这一领域的研究工作正在迅速展开。 1,4-丁炔二醇(BD)可用PdCl_2,ZnCl_2,(Ph_3P)_2PdCl_2等多种催化剂催化聚合,得到长链共轭的聚(1,4-丁炔二醇)(PBD)。苯乙炔(PA)可用热聚合,光聚合、电聚合、自由基聚合、等离子体聚合、催化聚合等聚合方法,得到长链共轭的聚苯乙炔     

带树枝状侧链聚苯乙炔的合成与结构表征

合成了带树枝状聚苯甲醚修饰基团的苯乙炔单体,在Rh[(nbd)Cl2]2催化剂的作用下得到了侧链带聚苯甲醚树枝的新型聚苯乙炔衍生物,用红外吸收光谱、核磁共振谱、紫外可见吸收光谱和凝胶渗透色谱表征了聚合物的结构.发现聚合物的重均分子量达到了57300,在氯仿、N,N-二甲基甲酰胺、四氢呋喃等有机溶剂中有良好的溶解性能.由于侧链上聚苯甲醚树枝体积庞大,聚合物主链采取立构规整的顺-顺式构象,紫外可见吸收光谱在440nm附近出现了显著的共轭主链的吸收肩峰;立构规整的顺-顺式构象使树枝状侧链形成了对主链保护的"夹套效应",聚合物热分解温度从聚苯乙炔母体的225℃提高到295℃.     

茂钛/MAO催化体系进行降冰片烯聚合的研究

以降冰片烯为例的环状烯烃的聚合方式主要有两种 :( A) Vinyl-type polymerization;( B) Ring-Opening Polymerization　　 80年代中期以前 ,环烯烃聚合研究主要集中在开环易位聚合 (ROMP)反应 [1] .Kaminsky[2 ] 首次以[En(Ind) 2 Zr Cl2 ]/MAO等为催化剂进行降冰片烯的聚合 ,获得了熔点极高 (高于其 40 0℃的分解温度 )的大分子量加成结构的聚合物 .研究结果表明 ,具有 C2 和 Cs对称性的茂锆催化体系能高活性地得到降冰片烯加成聚合物 [3,4 ] ,但是这些由茂锆催化体系合成的降冰片烯聚合物不溶于有机溶剂 ,难以进行精确定量的结…     

Rh_4(CO)_(12)和[Rh(CO)_2Cl]_2催化1—己烯氢甲酰化反应研究

研究了Rh_4(CO)_(12)和[Rh(CO)_2Cl]_2两种铑原子簇合物在1—已烯氢甲酰化反应中的催化性能和反应前后催化剂溶液的红外光谱变化。结果表明,按加入的Rh_4(CO)_(12)和[Rh(CO)_2Cl]_2的分子数计算,前者的催化活性比后者高出一倍多;若按铑原子数计算,则二者活性较接近。红外光谱测定说明,Rh_4(CO)_(12)的簇结构反应前后无显著变化。然而,[Rh(CO)_2Cl]_2参与反应后却变成了以Rh_4(CO)_(12)为主的簇合物。反应过程中两种催化剂母体可能解离成类似的单核铑催化活性物种,反应之后,在常温常压下又聚合为簇合物。     

含膦酰杂菲侧基聚乙炔的合成与热稳定性

以2-(6-氧化-6-氢-二苯基(c,e)<1,2>氧杂磷酰基)-1,4-二羟基苯(ODOPB)结构单元为中心,在两侧通过酯化反应分别引入4-乙炔基苯甲酰基和4-烷氧基苯甲酰基,并作为乙炔单体,在[Rh(nbd)Cl]2催化下,30℃聚合得到了含磷酰杂菲(DOPO)基团的聚乙炔.1H-NMR和GPC分析表明,由于DOPO存在较大π共轭结构和较强极性效应,在诱导聚乙炔主链采取高反式构型的同时,增加了分子链内相邻侧基之间的相互作用,使整个分子链趋向二维共平面结构,有利于增强分子链之间的相互作用.TGA显示,与不含磷酰杂菲侧基的模型聚乙炔相比,DOPO的引入使聚乙炔呈现良好的热稳定性,起始热分解温度(T5%)接近400℃,说明通过增强分子链内侧基间相互作用有助于提高热稳定性.     

侧链带有L-氨基酸乙酯的螺旋聚苯乙炔衍生物的手性识别能力研究

采用Rh(nbd)BPh4催化剂合成了3种侧链带有L-氨基酸乙酯的螺旋聚苯乙炔衍生物PPA-S-Phe、PPA-S-Leu和PPA-A-Leu,并将其涂覆在氨丙基硅胶上制备高效液相色谱(HPLC)手性固定相(CSP),研究其对7种对映体的手性识别能力.由于侧链手性基团或主链与手性基团之间的链接基团不同,PPA-S-Phe、PPA-S-Leu和PPA-A-Leu形成了不同的螺旋构象,并表现出对对映体不同的手性识别能力.PPA-S-Phe和PPA-S-Leu的主链与手性基团之间的链接基团均为磺酰胺基,侧链手性基团为L-亮氨酸乙酯的PPA-S-Leu的手性识别能力优于侧链手性基团为L-苯丙氨酸乙酯的PPA-S-Phe.PPA-S-Leu和PPA-A-Leu的侧链手性基团均为L-亮氨酸乙酯,以酰胺基为链接基团的PPA-A-Leu的手性识别能力明显优于以磺酰胺基为链接基团的PPA-S-Leu.螺旋聚苯乙炔主链与侧链手性基团之间的链接基团、侧链手性基团在手性识别中均发挥十分着重要作用.     

用稀土催化剂合成特高顺式聚丁二烯

本文较详细地考察了丁二烯在Nd(naph)_3-Al(i-C_4H_9)_2H-Al(i-C_4H_9)_2Cl催化体系中聚合时,催化剂用量及组份配比,聚合温度对聚合物微观结构及分子量的影响。首次采用稀土催化体系合成出了[η]_甲苯~30℃为3.0-3.5(分升/克),顺-1,4链节含量达99％的聚丁二烯。提出了聚合物的活性链端为π-烯丙基氯化物结构,聚合物的微观结构取决于活性链端的链增长和异构化的相对速度的假设。     

含手性三联苯腰接型液晶聚乙炔的合成及其“甲壳效应”

设计、合成了一种新单体,并由[Rh(nbd)Cl]2/Et3N(nbd =2,5-降冰片二烯)催化聚合反应制备了一种具有较高相对分子质量(质均相对分子质量为30300)的含手性三联苯液晶聚乙炔PAM3OCO(TPh)(OR*)2{一[(CH=C(CH2)3OCO-terphenyl(OR*)2]n—,R*=(S)-2-甲基丁基}.由于手性基团和三联苯液晶基元的引入,单体具有互变手性近晶C相,而聚合物则呈现互变的手性近晶A相液晶行为.三联苯液晶基元以重心位置连接于聚合物主链并围绕主链所产生的“甲壳效应”赋予了聚合物很高的热稳定性(356℃)、发光性能和聚集诱导增强发光特性.其薄膜状态下的发光强度明显大于其在稀溶液状态下的发光强度,且内量子效率和外量子效率分别为0.214和0.023.紫外光激发下,聚合物在液晶状态下的发光强度明显优于溶液和薄膜状态,并且发光谱带发生了红移.     

以膦酰杂菲为侧基的1-戊炔聚合反应及其结构与热力学性质

以2-(6-氧化-6-氢-二苯基(c,e)<1,2>氧杂膦酰基)-1,4-二羟基苯(ODOPB)结构单元为中心,在两侧通过酯化反应分别引入4-(4-戊炔氧基)苯甲酰基和4-丁氧基苯甲酰基,得到了1-戊炔衍生物单体M-34,同时合成了不含9,10-二氢-9-氧杂-10-膦杂菲-10-氧化物(简称膦酰杂菲,DOPO)基元的M-34模型化合物M-0.分别以[Rh(nbd)Cl]2和Rh(nbd)B(C6H5)4为催化剂,研究了催化剂浓度和聚合时间对M-34和M-0聚合反应收率的影响.结果表明,由于DOPO存在较大π共轭结构和较强极性效应,降低了催化剂的活性,使得聚合产物P-34分子量较低,但改善了P-34的溶解性,并诱导P-34主链基本采取全反式构型,从而有利于增强侧基之间的相互作用,使这种含有DOPO的聚1-戊炔衍生物呈现良好的热稳定性,且优于其不含DOPO模型聚合物P-0的热稳定性.但同时DOPO的引入也增加侧基的体积,为链段运动提供了较大的自由体积,使得P-34的Tg低于不含DOPO模型聚合物P-0的Tg.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.