NaOH含量对HZSM-5分子筛性质及其催化甲缩醛气相羰基化性能的影响

通过调变合成过程中NaOH的含量,制备了一系列HZSM-5分子筛,并对其催化甲缩醛(DMM)气相羰基化合成甲氧基乙酸甲脂(MMAc)反应性能进行了详细考察。结果表明,本合成体系中,NaOH含量为0.8%(质量分数)时,ZSM-5分子筛表现出最佳的催化活性。BET、~(27)Al NMR、NH_3-TPD、Py-FTIR等多种表征结果证实NaOH含量的改变可有效调变分子筛孔道中介孔孔容及中强Br?nsted酸(B酸)位点的分布,两者是影响分子筛催化活性的主要因素。中强B酸位点增加,原料DMM反应加剧,转化率提高;介孔孔容增大,产物扩散途径缩短,孔道限域效应减弱,副反应被抑制, MMAc选择性增加。进一步采用密度泛函理论对DMM与HZSM-5分子筛作用过程进行了初步探索,发现反应过程中将首先形成甲氧基甲基(ZOCH_2OCH_3)中间物种,在此基础上,提出了DMM羰基化生成MMAc的可能机制。     

ZSM-5分子筛酸位分布及其甲醇制烯烃催化性能的定向管理与调控（英文）

ZSM-5分子筛在甲醇制烯烃(MTO)过程中的催化性能和反应机理与其孔道中酸位点分布位置紧密相关.本文证明在水热合成过程中加入适量的钠离子(Na~+)可以增加ZSM-5分子筛交叉腔酸位点比例;从而促进高级甲基苯的生成并加速芳烃循环,有利于乙烯生成.相反,在合成过程中不添加钠离子,所制备的ZSM-5分子筛直孔道和正弦孔道酸位点比例明显提高,有利于促进烯烃循环并提高丙烯和C_(3+)烯烃选择性.     

ZSM-5分子筛酸位分布及其甲醇制烯烃催化性能的定向管理与调控

ZSM-5分子筛在甲醇制烯烃(MTO)过程中的催化性能和反应机理与其孔道中酸位点分布位置紧密相关. 本文证明在水热合成过程中加入适量的钠离子(Na⁺)可以增加ZSM-5分子筛交叉腔酸位点比例; 从而促进高级甲基苯的生成并加速芳烃循环, 有利于乙烯生成. 相反, 在合成过程中不添加钠离子, 所制备的ZSM-5分子筛直孔道和正弦孔道酸位点比例明显提高, 有利于促进烯烃循环并提高丙烯和C₃₊烯烃选择性.     

ZSM-5酸改性对甲醇芳构化性能的影响

利用硝酸、草酸和酒石酸溶液对ZSM-5分子筛进行改性,并采用XRD、SEM、NH₃-TPD、XRF、²⁷Al MAS NMR、吡啶吸附红外光谱和N₂吸附-脱附对ZSM-5分子筛结构、酸量、比表面积及孔体积等物化性质进行表征分析。在反应温度为422℃,甲醇质量空速为4.74 h^-1的条件下,考察了ZSM-5分子筛的催化活性。结果表明,采用不同酸改性ZSM-5分子筛,影响了分子筛的比表面积、酸性及孔体积,从而改变了催化剂的催化性能。在甲醇芳构化（MTA）反应中,酸改性后的分子筛表现出良好的催化活性,且草酸改性后的催化剂表现出较高的催化活性及选择性,反应8 h时,芳烃及BTX收率分别达到57.40%和39.40%。     

纳米Pd/ZSM-5的原位法制备及催化肉桂醛加氢

采用共沸精镏辅助的原位法成功合成了高度分散的Pd纳米颗粒负载在ZSM-5中（Pd/ZSM-5-IS）分子筛催化剂。通过XRD、TEM、XPS等手段对Pd/ZSM-5-IS的样品进行了表征,并考察反应压力、反应温度、反应时间对肉桂醛加氢催化性能的影响。结果表明：原位法制备的Pd/ZSM-5-IS催化剂比浸渍法制备的Pd/ZSM-5-IM催化剂具有更高的催化稳定性,其主要归因于Pd纳米颗粒进入ZSM-5的晶内介孔有效防止活性位点的损失和聚集。当反应温度为80℃,反应压力为1 MPa,反应时间为3 h时为最佳反应条件,肉桂醛的转化率为87.23%,苯丙醛的选择性为76.68%。     

两段变温法水热合成多级孔ZSM-5分子筛及其催化裂化性能（英文）

以四丙基氢氧化铵(TPAOH)为单一模板剂,采用低温老化、高温晶化2段变温法合成出了球状多级孔ZSM-5分子筛。利用XRD、FT-IR、NH_3-TPD、SEM、TEM以及氮气吸-脱附等测试对合成样品进行了表征。结果表明:直径约为2μm左右的球状多级孔ZSM-5分子筛颗粒内的晶间介孔和大孔主要由棒状纳米晶堆积而成的,该产品具有较大的比表面积和介孔孔容。同常规水热法一步合成的微孔ZSM-5分子筛相比,2段变温法合成的多级孔ZSM-5分子筛具有更高的B酸/L酸比例(C_(BP)/C_(LP))、强酸/弱酸比例(C_s/C_w)以及活性位可接近性指数(ACI)。催化裂化评价结果显示,得益于活性位可接近性指数等指标的提高,球状多级孔ZSM-5分子筛比常规合成的微孔ZSM-5分子筛具有更高的转化率和丙烯收率等优异的催化性能。     

特殊形貌类雪花状ZSM-5分子筛的合成、表征及甲醇制烯烃催化性能(英文)

美国Mobil公司于1972年首先开发的ZSM-5分子筛是一种高硅三维交叉孔道的沸石分子筛,其孔道结构具有良好的择形作用,因此被广泛应用于芳构化、异构化、烷基化和催化裂化等工业催化过程.ZSM-5分子筛的催化性能与其晶粒尺寸、酸性及形貌等密切相关.改变合成方法和制备参数可以合成出不同形貌的ZSM-5分子筛,但目前关于ZSM-5分子筛形貌对其物理化学性质和催化性能的影响报道较少.本文通过改变模板剂类型,采用水热合成法,制备出了类雪花状、椭圆柱状和夹心糖状三种不同形貌的ZSM-5分子筛.通过X射线荧光光谱(XRF)、N_2物理吸脱附(BET)、扫描电镜(SEM)、X射线衍射(XRD)、固体核磁共振(MAS NMR)、NH_3程序升温脱附(NH_3-TPD)及吸附吡啶的红外光谱(Py-IR)等手段对不同形貌分子筛的物理化学性质、形貌、晶体骨架结构和酸性进行了表征.采用浸渍法制备了Ca/HZSM-5催化剂,以甲醇制烯烃(MTO)为探针反应、着重研究了ZSM-5分子筛形貌和晶体结构特性对其酸性和催化性能的影响.合成的三种不同形貌的ZSM-5分子筛具有相近的SiO_2/Al_2O_3比和比表面积.XRD结果表明,通过改变模板剂类型,可制得结晶度较好的ZSM-5分子筛,其中类雪花状分子筛的(101)晶面比例明显多于其它两种分子筛,而椭圆柱状分子筛则暴露更多的(020)晶面.~(27)Al MAS NMR结果表明,绝大部分Al都以四配位形式存在于三种分子筛骨架中,而类雪花状分子筛的峰强度较低,这是由于Al的配位环境不同(偶极作用弱),说明在类雪花状分子筛的交叉晶面中存在大量扭曲、错位和不对称结构;与其它两种分子筛相比,类雪花状分子筛的~(29)Si MAS NMR谱峰宽化、进一步证明该分子筛骨架结构中存在扭曲、错位和不对称性.NH_3-TPD结果表明,类雪花状HZSM-5分子筛的酸量明显高于其它两种分子筛,在SiO_2/Al_2O_3比相近的情况下、类雪花状HZSM-5分子筛晶体骨架结构的错位、扭曲和不对称性造成了该分子筛中酸量增加;但Py-IR结果表明,类雪花状HZSM-5分子筛的酸量低于其它两种分子筛,这与NH_3-TPD结果有差异,主要是由于类雪花状分子筛几何空间结构和晶界处的扭曲、错位对孔道结构的影响,不利于比NH_3分子大的吡啶分子的扩散,进而影响了吡啶分子在酸性位上的吸附.三种不同形貌的ZSM-5分子筛经Ca改性后比表面积和微孔比表面积均明显下降,其中类雪花状和椭圆柱状催化剂的微孔比表面积下降幅度较大,外比表面积下降幅度较小.这是因为各分子筛的晶体结构和晶面的取向差异,导致Ca离子在分子筛上的扩散行为不同.同时,经Ca改性后,三个催化剂的总酸量均有下降,尤其是类雪花状分子筛酸量下降较为明显,表明其中Ca离子更容易扩散到分子筛孔道内,与更多的酸性位作用,而夹心糖状分子筛表面具有更多的Z字形孔道,不利于Ca离子扩散到分子筛孔道内,因而酸量下降较少.Py-IR结果表明,Ca改性后催化剂的总酸量下降,尤其是B酸明显降低,L酸略有增加,其中类雪花状ZSM-5分子筛催化剂的B酸量最低.甲醇制烯烃反应评价结果表明,随着反应温度升高,三个催化剂的总烯选择性和丙烯选择性均呈先升高后降低的趋势.类雪花状ZSM-5分子筛催化剂在甲醇转化率相近时具有最高的烯烃选择性,在反应温度为460℃时,总烯烃选择性为72%,丙烯选择性达39%.     

芬顿试剂改性ZSM-5分子筛上丙烯齐聚反应研究

采用浸渍法分别制备了芬顿试剂及其原料FeSO_4和H_2O_2改性的ZSM-5分子筛,并与未改性的母体ZSM-5分子筛进行了对比实验。通过一系列表征手段及丙烯齐聚反应考察了各催化剂的理化性质和催化性能。结果表明,芬顿试剂、FeSO_4、H_2O_2的改性处理均会引起ZSM-5分子筛脱铝,从而导致其硅铝比升高。但与FeSO_4改性相比,芬顿试剂由于其产生的大量羟基自由基更容易将Fe引入分子筛,形成新的活性中心,同时芬顿试剂改性还能使分子筛的比表面积和介孔的体积增大,调节催化剂的酸性。与母体ZSM-5相比,Fenton-ZSM-5催化剂具有优异的催化活性和稳定性。初始丙烯转化率和柴油选择性分别高达98.3%和92.4%,24 h内转化率和选择性维持在80%和82%以上。     

纳米Pd/ZSM-5的原位法制备及催化肉桂醛加氢

采用共沸精镏辅助的原位法成功合成了高度分散的Pd纳米颗粒负载在ZSM-5中(Pd/ZSM-5-IS)分子筛催化剂。通过XRD、TEM、XPS等手段对Pd/ZSM-5-IS的样品进行了表征,并考察反应压力、反应温度、反应时间对肉桂醛加氢催化性能的影响。结果表明:原位法制备的Pd/ZSM-5-IS催化剂比浸渍法制备的Pd/ZSM-5-IM催化剂具有更高的催化稳定性,其主要归因于Pd纳米颗粒进入ZSM-5的晶内介孔有效防止活性位点的损失和聚集。当反应温度为80℃,反应压力为1 MPa,反应时间为3 h时为最佳反应条件,肉桂醛的转化率为87.23%,苯丙醛的选择性为76.68%。     

碱处理法改善Pt／ZSM-5异构化性能

制备了一系列不同条件下碱处理的ZSM-5样品,以调控其酸性和孔道结构. 考察了酸性和孔道结构对Pt/ZSM-5的异构化性能的影响. 样品的晶相、酸性及结构分别通过X射线衍射、 NH3程序升温脱附及N2吸附-脱附表征. 结果表明,缓和的碱处理导致ZSM-5上强酸中心减少,催化剂异构化活性下降; 而苛刻条件下的碱处理使得ZSM-5上强酸中心增加、大量中孔产生及催化剂异构化活性明显提高. 催化剂的异构化活性取决于分子筛上强酸中心的量,与孔道结构无关; 而异构体的分布不仅与孔道结构有关,而且与正己烷转化率密切相关,与分子筛的酸性无关.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。