氧化硅对金红石相纳米TiO2微结构的影响

通过硅酸钠水解生成的无定形氧化硅对金红石相纳米TiO₂进行修饰,利用红外光谱、紫外-可见漫反射光谱、X射线衍射、透射电镜和比表面仪对纳米TiO₂进行了表征。结果表明,氧化硅沉积在纳米TiO₂的表面和颗粒之间形成一个空间网络体系,有效地抑制了TiO₂晶粒尺寸和原始粒径的长大。当热处理温度低于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸、原始粒径和比表面积几乎不变;当热处理温度高于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸和原始粒径开始缓慢变大,比表面积快速下降,在900 ℃下煅烧2 h,经氧化硅处理的纳米TiO₂原始粒径仍为20～40 nm。氧化硅的存在使纳米TiO₂吸收紫外线的能力增强并使其平均孔径变小。     

高比表面TiO2光催化剂的制备及产氢性能研究

以钛酸四丁酯为前驱体，十六烷基三甲基溴化铵(CTAB)为模板剂合成了高比表面的TiO₂超细纳米粉体。采用XRD、TEM、BET分析方法对催化剂的物相、颗粒粒径及比表面积进行了表征，结果显示TiO₂的晶粒尺寸和比表面积与CTAB添加量和焙烧温度有关。重点考察了不同条件下制备的TiO₂系列光催化剂无氧条件下的光催化分解水产氢性能。实验结果表明，当CTAB与Ti的投料的物质的量之比为0.15，焙烧温度为450 ℃时，获得的晶粒尺寸为5.73 nm、比表面为150 m²·g^-1的TiO₂粉体具有最好的光催化产氢活性，测得的3 h内平均产氢速率为12.5 mL·h^-1。     

纳米TiO2低温水解法的晶型控制合成及其表面织构的研究

分别以TiCl₄，Ti(NO₃)₄和Ti(SO₄)₂为前驱体，在低温和强酸性条件下，通过水解反应可控地合成了具有不同晶相组成，且比表面积较高的纳米TiO₂，并用XRD，TEM和N₂^-吸附脱附技术对其晶相、粒径大小、形貌及比表面积进行了表征。结果表明，钛离子在有Cl^-、NO₃^-存在的酸性溶液中水解，水解温度≤80 ℃，可以生成结晶良好的具有细小晶粒尺寸和较高比表面积的金红石型纳米TiO₂粉体，水解温度>80 ℃，反而有锐钛矿型TiO₂生成，而在有SO₄^2-存在的酸性溶液中，TiO₂样品的晶相组成不随水解温度的变化而改变，均为锐钛矿型，其比表面积可达300 m²·g^-1。     

水热法制备具有高光催化活性的镧掺杂二氧化钛纳米晶

采用水热法合成钛酸钾(K₂Ti₈O₁₇)纳米棒,并将它作为前驱体水热转晶合成TiO₂纳米晶,同时通过在水热体系中引入稀土元素La³⁺实现对TiO₂的La掺杂.考察了不同条件下钛酸盐向TiO₂的转晶过程,发现水热溶液的pH值、温度以及预处理步骤对转晶过程有很大的影响.利用X射线衍射以及透射电子显微镜对样品的晶相和形貌进行了表征.利用电感耦合等离子体原子发射光谱测量了所合成的La掺杂TiO₂样品中的La含量.通过在紫外光下降解甲基橙(MO,10mg/L)测试了La掺杂TiO₂样品的光催化性能.结果表明La掺杂后TiO₂的光催化活性大大提高.在0.15mol/LLa³⁺浓度下180oC水热合成的La掺杂TiO₂样品显示了最佳的光催化活性.其对MO的光催化降解反应常数高达0.11min^-1,大约是空白TiO₂样品的9.20倍,P25TiO₂的3.69倍.     

氟改性纳米TiO2的制备及其光催化降解甲基橙机理

采用简易的沉淀-氟化-回流晶化法在低温下制备了氟改性纳米TiO₂ (F-TiO₂), 并通过透射电镜(TEM), X射线衍射(XRD), 傅里叶变换红外(FTIR)光谱, X射线光电子能谱(XPS)和漫反射光谱(DRS)等表征手段研究了粉末的形貌、晶型、元素形态和光吸收性质. 结果表明: 实验制得的F-TiO₂为椭圆形纳米颗粒, 粒径为5-8 nm; 氟离子能够有效抑制板钛矿相TiO₂的生成, 并同时提高锐钛矿相TiO₂的晶化度; 修饰的氟主要分布在TiO₂表面, 以化学吸附态为主, 并伴有少量的间隙氟. 光催化降解甲基橙的实验表明, 氟离子改性的TiO₂同时具有较高的全谱和可见光催化活性. 通过碱洗和焙烧的对照实验分析可知, F-TiO₂在可见光下降解甲基橙的机理是源于一种由TiO₂表面吸附氟和间隙氟共同增强的染料敏化降解作用.     

不同原料合成的TiO2的变温拉曼光谱分析

分别以钛酸四丁酯、钛酸四异丙酯、钛酸四乙酯为原料, 用溶胶凝胶法合成出TiO₂, 利用变温拉曼及变温XRD研究了不同原料相同方法合成得到的TiO₂的相转变温度. 结果表明, 所合成TiO₂的相转变温度与原料的反应活性存在对应关系, 根据锐钛矿拉曼特征峰半峰宽与温度的关系图, 将锐钛矿晶粒尺寸与半峰宽关联. 分析对比原料水解活性与产品相转变温度之间的关系对实验结果进行了解释.     

不同原料合成的TiO2的变温拉曼光谱分析

分别以钛酸四丁酯、钛酸四异丙酯、钛酸四乙酯为原料, 用溶胶凝胶法合成出TiO₂, 利用变温拉曼及变温XRD研究了不同原料相同方法合成得到的TiO₂的相转变温度. 结果表明, 所合成TiO₂的相转变温度与原料的反应活性存在对应关系, 根据锐钛矿拉曼特征峰半峰宽与温度的关系图, 将锐钛矿晶粒尺寸与半峰宽关联. 分析对比原料水解活性与产品相转变温度之间的关系对实验结果进行了解释.     

Na2SO4辅助水热合成SnO2纳米晶

系统地研究了以SnCl₄·5H₂O为原料，以Na₂SO₄为矿化剂，采用水热法在较低温度下和较短的反应时间内制备结晶良好并均匀分散的SnO₂纳米晶。采用X射线衍射(XRD)、透射电子显微镜(TEM)、红外光谱(IR)等技术对水热反应的晶化过程进行了分析。结果表明：在Na₂SO₄存在的情况下，在120 ℃反应4 h 即可制备得到晶粒细小，分散性能良好的SnO₂纳米晶。XRD衍射峰峰宽随水热温度的升高或反应时间的延长而变窄，结晶性提高。TEM结果表明产物颗粒小、分散性能良好。水热反应温度和反应时间对产物结晶度和粒径有明显的影响。对Na₂SO₄在反应过程中的作用机理进行了分析。     

N掺杂对TiO2形态结构及光催化活性的影响

以TiCl₄为钛源,采用酸催化水解法合成TiO₂前驱体,在NH₃/N₂气氛下经不同温度处理制得浅黄色的N掺杂TiO₂(TON)光催化剂。以苯酚为模型物,考察了催化剂在紫外光区、可见光区及太阳下催化活性;采用DRS、XPS、XRD、FTIR、SEM及低温氮物理吸附对光催化剂的晶相结构、光谱特征和表面结构等进行表征。系统研究了N掺杂对TiO₂形态结构及光催化活性的影响。结果表明,掺杂N以阴离子形式进入TiO₂体相中置换晶格中的O,适宜温度下制得适量N掺杂的TON在紫外光区、可见光区及太阳光下均表现出较高的活性。N掺杂在TiO₂表面生成Ti-O-N键,形成新的能级结构,使催化剂的吸收红移至450～550 nm,诱发TiO₂可见光催化活性。同时高温下煅烧,N掺杂可抑制TiO₂晶粒生长,减缓TiO₂粒子间团聚,提高锐钛矿相向金红石相转变温度,减缓相转化速度。     

钕的氢氧化物和氧化物纳米线的制备及表征

以金属钕为起始原料，采用简单的碱性溶液下水热法制备出氢氧化钕纳米线。所得到的水热产物采用X-射线衍射、扫描电镜和透射电镜等进行了结构与形态表征。研究发现，水热处理的温度、碱液浓度和碱的种类等对水热产物的形貌、长径比和结晶状态有较大影响，提高水热温度和增加碱液浓度有利于氢氧化钕纳米线的生长。在相同水热反应温度(180 ℃)、水热时间(45 h)和碱浓度下，5 mol·L^-1 NaOH溶液体系制备的氢氧化钕纳米线具有较高纯度和较长的长径比，其直径为20～40 nm，长度为2～10 μm。该氢氧化钕纳米线在空气气氛下500 ℃烧结后形成具有体心立方结构的C型Nd₂O₃，该Nd₂O₃仍具有一维纳米线形貌。升高焙烧温度时产物的形貌和相结构都发生了明显变化。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。