焙烧温度对In2TiO5纳米带晶型结构及光催化性能的影响

以Ti(OC₄H₉)₄、In(NO₃)₃和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In₂TiO₅纳米带。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-Vis DRS)和N₂吸附-脱附等技术对不同焙烧温度处理得到的样品进行表征,详细研究了焙烧温度对In₂TiO₅纳米带晶粒尺寸、形貌、比表面积和孔径的影响。以20 mg·L^-1的氟喹诺酮类抗生素左氧氟沙星(LEV)为目标降解物,125 W高压汞灯为光源,评价了不同焙烧温度下In₂TiO₅纳米带的光催化活性。结果表明,焙烧温度对In₂TiO₅的形貌与光催化活性有明显影响。当焙烧温度为800℃时,制备的In₂TiO₅纳米带表面光滑,其宽度为(552±58) nm、厚度约为140 nm,光催化活性最强,光照60 min,LEV的降解率可以达到95%。     

焙烧温度对In2TiO5纳米带晶型结构及光催化性能的影响

以Ti(OC₄H₉)₄、In(NO₃)₃和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In₂TiO₅纳米带。利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-Vis DRS)和N₂吸附-脱附等技术对不同焙烧温度处理得到的样品进行表征,详细研究了焙烧温度对In₂TiO₅纳米带晶粒尺寸、形貌、比表面积和孔径的影响。以20 mg·L^-1的氟喹诺酮类抗生素左氧氟沙星(LEV)为目标降解物,125 W高压汞灯为光源,评价了不同焙烧温度下In₂TiO₅纳米带的光催化活性。结果表明,焙烧温度对In₂TiO₅的形貌与光催化活性有明显影响。当焙烧温度为800℃时,制备的In₂TiO₅纳米带表面光滑,其宽度为(552±58) nm、厚度约为140 nm,光催化活性最强,光照60 min,LEV的降解率可以达到95%。     

纳米TiO2低温水解法的晶型控制合成及其表面织构的研究

分别以TiCl₄，Ti(NO₃)₄和Ti(SO₄)₂为前驱体，在低温和强酸性条件下，通过水解反应可控地合成了具有不同晶相组成，且比表面积较高的纳米TiO₂，并用XRD，TEM和N₂^-吸附脱附技术对其晶相、粒径大小、形貌及比表面积进行了表征。结果表明，钛离子在有Cl^-、NO₃^-存在的酸性溶液中水解，水解温度≤80 ℃，可以生成结晶良好的具有细小晶粒尺寸和较高比表面积的金红石型纳米TiO₂粉体，水解温度>80 ℃，反而有锐钛矿型TiO₂生成，而在有SO₄^2-存在的酸性溶液中，TiO₂样品的晶相组成不随水解温度的变化而改变，均为锐钛矿型，其比表面积可达300 m²·g^-1。     

氧化硅对金红石相纳米TiO2微结构的影响

通过硅酸钠水解生成的无定形氧化硅对金红石相纳米TiO₂进行修饰,利用红外光谱、紫外-可见漫反射光谱、X射线衍射、透射电镜和比表面仪对纳米TiO₂进行了表征。结果表明,氧化硅沉积在纳米TiO₂的表面和颗粒之间形成一个空间网络体系,有效地抑制了TiO₂晶粒尺寸和原始粒径的长大。当热处理温度低于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸、原始粒径和比表面积几乎不变;当热处理温度高于700 ℃时,经氧化硅处理的纳米TiO₂的晶粒尺寸和原始粒径开始缓慢变大,比表面积快速下降,在900 ℃下煅烧2 h,经氧化硅处理的纳米TiO₂原始粒径仍为20～40 nm。氧化硅的存在使纳米TiO₂吸收紫外线的能力增强并使其平均孔径变小。     

双介孔结构的纳米TiO2/I2复合材料的制备及其可见光催化性能

以钛酸丁酯为前驱体, 碘溶胶为碘源, 在室温下采用水解沉淀法制备了单质碘和纳米TiO₂复合的双介孔结构光催化剂(M-I₂-TiO₂). 采用X射线衍射(XRD)、透射电子显微镜(TEM)、比表面分析(BET)、紫外-可见(UV-Vis)漫反射光谱和傅里叶变换-红外光谱(FT-IR)对M-I₂-TiO₂进行了表征. 以次甲基蓝(MB)溶液为模拟废水, 对M-I₂-TiO₂的光催化性能进行了评价, 研究了不同热处理温度对光催化活性的影响. 结果表明, M-I₂-TiO₂在可见光区有显著的吸收, 300 ℃热处理得到的样品比表面积高达227.6 m²/g, 600 ℃热处理所得样品的比表面积仍高达111.8 m²/g, 而400 ℃热处理所得样品具有最好的光催化降解性能. 双介孔结构纳米TiO₂/I₂复合材料的光催化降解性能显著高于相同方法制备的纯TiO₂和Degussa P-25商业产品. 催化剂经6次重复使用其光催化活性基本保持不变.     

TiO2/石墨烯复合材料的合成及光催化分解水产氢活性

利用石墨粉根据Hummers氧化法制得氧化石墨,并进一步还原得到石墨烯。采用溶胶-凝胶法以钛酸四丁酯和石墨烯为起始材料制备了二氧化钛(TiO₂)和石墨烯的复合光催化材料。研究了该复合材料在紫外-可见光以及可见光条件下的光催化分解水制氢活性。结果表明,紫外-可见光照射下,TiO₂/石墨烯复合光催化材料的光催化分解水产氢速率为8.6 μmol·h^-1,远大于同条件下商业P25的产氢速率 (4.5 μmol·h^-1),光解水产氢活性提高了近2倍;可见光下光照3 h,TiO₂/石墨烯复合材料的光催化分解水产氢量约为0.2 μmol。     

纳米级TiO2粉体的制备研究——Ⅱ.絮凝剂及其浓度的影响

采用溶胶-凝胶-超临界流体干燥(SCFD)法制备纳米级TiO₂超细粉，详细考察了不同絮凝剂及其浓度对TiO₂织构和结构性质的影响。结果表明，利用强碱溶液作为絮凝剂，浓度为5 mol·L^-1是制备大孔高比表面TiO₂超细粉较为适宜的条件。     

以乙二醇为电子给体在CuO/TiO2上光催化分解水制氢

采用浸渍、热分解的方法在TiO₂纳米颗粒上负载CuO制备得到光催化剂CuO/TiO₂。研究了以乙二醇为电子给体,在CuO/TiO₂上光催化分解水制氢的反应过程。重点分析考察了影响光催化产氢速率的因素如CuO的负载量、反应时间、光催化剂用量、乙二醇初始浓度等,同时对光催化制氢的反应机理进行了初步探讨。结果表明,氙灯光源模拟太阳光下最佳产氢速率达到604.5 μmol·h^-1·g^-1;CuO/TiO₂催化剂改善了光吸收性能、减少了光生载流子的复合速率,CuO可以起到传输电子的作用;乙二醇为电子给体很可能经过羟基乙醛进一步被氧化。     

以乙二醇为电子给体在CuO/TiO2上光催化分解水制氢

采用浸渍、热分解的方法在TiO₂纳米颗粒上负载CuO制备得到光催化剂CuO/TiO₂。研究了以乙二醇为电子给体,在CuO/TiO₂上光催化分解水制氢的反应过程。重点分析考察了影响光催化产氢速率的因素如CuO的负载量、反应时间、光催化剂用量、乙二醇初始浓度等,同时对光催化制氢的反应机理进行了初步探讨。结果表明,氙灯光源模拟太阳光下最佳产氢速率达到604.5μmol·h^-1·g^-1;CuO/TiO₂催化剂改善了光吸收性能、减少了光生载流子的复合速率,CuO可以起到传输电子的作用;乙二醇为电子给体很可能经过羟基乙醛进一步被氧化。     

TiO2形态结构与光催化活性关系的研究

本文介绍了TiO₂多相光催化剂的作用机理及其结构特性对光催化活性的影响,并对TiO₂的晶相组成、晶粒尺寸、比表面积、表面形态与光催化活性的关系作了综述。     

Li_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3,Na_(1.3)Ti_(1.7)Al_(0.3)(PO_4)_3的离子交换研究

研究了在不同温度下的NaNO3和AgNO3水溶液中Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3离子交换行为.实验表明Li1.3Ti1.7Al0.3(PO4)3和Na1.3Ti1.7Al0.3(PO4)3均显示出了高选择性与Na+和Ag+进行离子交换的特征,且对Ag+的选择性高于Na+.升高温度可显著提高Ag/Li和Ag/Na的交换反应速度.     

Crystal growth, structure determination, and optical properties of new potassium-rare-earth silicates K3RESi2O7 (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu)

Single crystals of K₃RESi₂O₇ (RE=Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu) were grown from a potassium fluoride flux. Two different structure types were found for this series. Silicates containing the larger rare earths, RE=Gd, Tb, Dy, Ho, Er, Tm, Yb crystallize in a structure K₃RESi₂O₇ that contains the rare-earth cation in both a slightly distorted octahedral and an ideal trigonal prismatic coordination environment, while in K₃LuSi₂O₇, containing the smallest of the rare earths, lutetium is found solely in an octahedral coordination environment. The structure of K₃LuSi₂O₇ crystallizes in space group P6₃/mmc with a=5.71160(10) Å and c=13.8883(6) Å. The structures containing the remaining rare earths crystallize in the space group P6₃/mcm with the lattice parameters of a=9.9359(2) Å, c=14.4295(4) Å, (K₃GdSi₂O₇); a=9.88730(10) Å, c=14.3856(3) Å, (K₃TbSi₂O₇); a=9.8673(2) Å, c=14.3572(4) Å, (K₃DySi₂O₇); a=9.8408(3) Å, c=14.3206(6) Å, (K₃HoSi₂O₇); a=9.82120(10) Å, c=14.2986(2) Å, (K₃ErSi₂O₇); a=9.80200(10) Å, c=14.2863(4) Å, (K₃TmSi₂O₇); a=9.78190(10) Å, c=14.2401(3) Å, (K₃YbSi₂O₇). The optical properties of the silicates were investigated and K₃TbSi₂O₇ was found to fluoresce in the visible.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃-Bi₂O₃-ZnO-Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1 350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1 364,介电损耗低至1.2%。     

Near infrared study of aqueous rare-earth ethylsulfates

The near infrared spectra of aqueous solutions of the ethylsulfates of La, Nd, Gd, Tb, Er, Yb, Lu, Y, and Na have been determined from about 0.2 mol-dm^–3 to nearly saturation. The extinction coefficients of water have been calculated taking into account the absorption of ethylslfate anions determined in separate experiments. Their values appeared to be nearly the same as that of pure water. The relative contents of free OH groups in 0.5 and 0.7M solutions have been estimated from the absorbances at 1160 nm. They were lower in solutions of the heavy rare-earth ethylsulfates (Tb, Er, Yb, Lu) than in equimolar solutions of the lighter ones (La, Nd), confirming our previous view that secondary hydration of the heavy trivalent rare-earth cations is distinctly stronger than that of the lighter ones. A comparison of the spectra of these aqueous ethylsulfates with those of perchlorates shows that the structure-breaking ability of the C₂H₅SO ₄ ^– ion is much smaller than that of perchlorate anion.     

电感耦合等离子体光谱法(ICP-AES)测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量

针对银精矿样品复杂,难消解的特点,研究了不同酸溶法和碱熔法对样品的消解情况,建立了硝酸,盐酸,氢氟酸,高氯酸消解银精矿的方法。根据元素灵敏度和抗干扰性,选定各元素的测定波长。通过酸溶样和碱熔样测定结果比对,验证了方法准确性。建立了四酸消解-电感耦合等离子体光谱法测定银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的方法,元素的线性相关系数均在0.9999以上。通过共存元素干扰实验,确定了银精矿中高含量元素(铜、铅、锌、铁、锑、铋等)对测定元素结果没有影响。方法检出限：Cu 0.0063 mg/L, Pb 0.0159 mg/L ,Zn 0.0090 mg/L,As 0.0192 mg/L, Cd 0.0093 mg/L ,Ca 0.0084 mg/L, Mg 0.0075 mg/L, Mn 0.0081 mg/L。测定下限：Cu 0.0105mg/L,Pb 0.0265 mg/L, Zn 0.0150 mg/L, As 0.0320 mg/L, Cd 0.0155 mg/L, Ca 0.0140 mg/L, Mg 0.0125 mg/L,Mn 0.0135 mg/L。3个样品的相对标准偏差在0.87%~3.56%之间,加标回收率在95.00%~103.56%之间。方法流程短,操作简单,快速,灵敏度和再现性高,结果准确可靠,可以满足银精矿中铜、铅、锌、砷、镉、钙、镁、锰含量的测定。     

Structural studies of five layer Aurivillius oxides: A2Bi4Ti5O18 (A=Ca, Sr, Ba and Pb)

The room temperature structures of the five layer Aurivillius phases A₂Bi₄Ti₅O₁₈ (A=Ca, Sr, Ba and Pb) have been refined from powder neutron diffraction data using the Rietveld method. The structures consist of [Bi₂O₂]²⁺ layers interleaved with perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks. The structures were refined in the orthorhombic space group B2eb (SG. No. 41), Z=4, and the unit cell parameters of the oxides are a=5.4251(2), b=5.4034(1), c=48.486(1); a=5.4650(2), b=5.4625(3), c=48.852(1); a=5.4988(3), b=5.4980(4), c=50.352(1); a=5.4701(2), b=5.4577(2), c=49.643(1) for A=Ca, Sr, Ba and Pb, respectively. The structural features of the compounds were found similar to n=2-4 layers bismuth oxides. The strain caused by mismatch of cell parameter requirements for the [Bi₂O₂]²⁺ layers and perovskite-like [A₂Bi₂Ti₅O₁₆]²⁻ blocks were relieved by tilting of the TiO₆ octahedra. Variable temperature synchrotron X-ray studies for Ca and Pb compounds showed that the orthorhombic structure persisted up to 675 and 475 K, respectively. Raman spectra of the compounds are also presented.     

Metal-organic deposition of YBa2Cu3Ox and Bi2Sr2Ca1Cu2Ox films on various substrates starting from different fluorine-free metallorganic compounds

YBa₂Cu₃O_x (Y-123) and Bi₂Sr₂Ca₁Cu₂O_x (Bi-2212) films on various substrates have been prepared by Metal-Organic Deposition starting from different metallorganic fluorine-free compounds and using a very simple instrumentation. The processing conditions include a rapid pyrolysis step in air and an annealing step in oxygen for Y-123 and in air for Bi-2212. The films obtained have been characterized by X-ray diffraction (XRD) and the formation of a superconducting phase of Y-123 or Bi-2212 was confirmed measuring the critical temperature (T _c) with Ac-susceptibility and resistive measurements. Microstructure and final cationic ratios have been studied by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS).     

Decomposition of P2S2N4(Si(CH3)3)4A12C14 as Studied by FT-Raman and Quantum Chemistry Means

The dimeric title compound decomposes upon heating to give the monomer and desulphurized monomer as shown by FT-Raman and quantum chemical means.     

The crystal chemistry of Bi6TP2O15+x, T=Fe, Ni, Zn: Isomorphism and polymorphism, structural relationship to Bi6TiP2O16

The crystal structures of compounds with nominal compositions Bi₆FeP₂O_15+x (I), Bi₆NiP₂O_15+x (II) and Bi₆ZnP₂O_15+x (III) were determined from single-crystal X-ray diffraction data. They are monoclinic, space group I2, Z=2. The lattice parameters for (I) are a=11.2644(7), b=5.4380(3), c=11.1440(5) Å, β=96.154(4)°; for (II) a=11.259(7), b=5.461(4), c=11.109(7) Å, β=96.65(1)°; for (III) a=19.7271(5), b=5.4376(2), c=16.9730(6) Å, β=131.932(1)°. Least squares refinements on F² converged for (I) to R1=0.0554, wR₂=0.1408; for (II) R₁=0.0647, wR₂=0.1697; for (III) R₁=0.0385, wR₂=0.1023. The crystals are complexly twinned by 2-fold rotation about , by inversion and by mirror reflection. The structures consist of edge-sharing articulations of OBi₄ tetrahedra forming layers in the a-c plane that then continue by edge-sharing parallel to the b-axis. The three-dimensional networks are bridged by Fe and Ni octahedra in (I) and (II) and by Zn trigonal bipyramids in (III) as well as by oxygen atoms of the PO₄ moieties. Bi also randomly occupies the octahedral sites. Oxygen vacancies exist in the structures of the three compounds due to required charge balances and they occur in the octahedral coordination polyhedron of the transition metal. In compound (III), no positional disorder in atomic sites is present. The Bi-O coordination polyhedra are trigonal prisms with one, two or three faces capped. Magnetic susceptibility data for compound (I) were obtained between 4.2 and 350 K. Between 4.2 and 250 K it is paramagnetic, μ_eff=6.1 μ_B; a magnetic transition occurs above 250 K.     

Preparation of ZrO2-TiO2-CeO2 and Its Application in the Selective Catalytic Reduction of NO with NH3

TiO₂,ZrO₂-TiO₂,andZrO₂-TiO₂-CeO₂ were prepared by co-precipitation method and characterized by X-ray diffraction (XRD), specific surface area measurements (BET), temperature programmed desorption (NH₃-TPD), oxygen storage capacity (OSC), and temperature programmed reduction (H₂-TPR). The results showed that ZrO₂-TiO₂-CeO₂ exhibited large number of surface strong acid, possessed some oxygen storage capacity, and strong redox property. The three materials were used as supports and the monolith catalysts were prepared with 1% (w) V₂O₅ and 9% (w)WO₃ for selective catalytic reduction (SCR) of NO with ammonia in the presence of excessive O₂, and the results of catalytic activity showed that the catalyst used ZrO₂-TiO₂-CeO₂ as support yielded nearly 100% NO conversion at 275 °C at a gas hourly space velocity (GHSV) of 10000 h⁻¹, and it had the best catalytic activity and showed great potential for practical application.