TiO2纳米薄片的合成及其光催化降解苯酚性能

以钛酸纳米管为前驱体,通过添加NaF高温水热合成了(001)面暴露的TiO₂纳米薄片,并对其催化苯酚光降解行为进行了研究。结果表明经水热反应后,钛酸型TiO₂纳米管(NT)转晶成锐钛矿型TiO₂纳米薄片(NS),且具有高(001)暴露面。和NT相比,NS对苯酚的光催化降解活性显著提高,其活性随水热温度升高而增加。NS光催化去除苯酚符合一级动力学,其中200 ℃合成的NS反应速率常数k最高,为0.083 min^-1。同时,苯酚的光催化反应初活性与其初浓度的关系符合Langmuir-Hinshelwood模型,表明苯酚的光催化降解受吸附控制。     

原位红外光谱法研究La/TiO2对有机污染物的光催化降解

本工作采用改进的溶胶-凝胶法和浸渍法制备了TiO₂掺杂稀土离子La³⁺的La/TiO₂光催化剂，运用XRD、N₂吸附脱附、紫外可见漫反射光谱(DRS)、表面光电压谱(SPS)等手段进行表征，同时利用原位红外技术考察了La/TiO₂样品光催化降解乙烯、丙酮、苯的气-固相光催化氧化反应，对其光催化降解有机污染物的过程进行了研究。结果表明，TiO₂经适量La³⁺掺杂后，锐钛矿晶型的含量增加，晶粒度减小，比表面积增大，禁带宽度增加，表面光电压信号增强，光生电子-空穴对有效分离；La/TiO₂样品对乙烯、丙酮、苯的光催化性能与纯TiO₂相比均有不同程度的改善，乙烯可以被光催化氧化完全矿化生成CO₂，而丙酮被光催化氧化可能生成中间产物丙酸，苯被光催化氧化可能生成中间产物苯酚和苯醌。     

La和Cu掺杂对纳米TiO2光生电荷性质的影响及其与光催化活性的关系

采用溶胶-水热法制备了未掺杂的和分别掺杂1%(摩尔浓度)La的、Cu的及La和Cu共掺杂的纳米TiO₂, 并主要利用表面光电压谱(SPS)和光致发光光谱(PL)等技术考察了掺杂对纳米TiO₂表面光生电荷性质的影响, 也探讨了其性质与光催化活性的关系. 结果表明: La的掺杂能够抑制TiO₂相变, 同时其不仅促进TiO₂光生载流子分离, 而且丰富了束缚表面态. 但是Cu的掺杂却与La的作用相反. 这些解释了在光催化氧化降解罗丹明B过程中, La掺杂有利于TiO₂光催化活性的提高, 而Cu掺杂对光催化反应是不利的. 此外, La和Cu共掺杂并没有体现出协同效应.     

TiO2/Gd2O3纳米粉体的制备、表征及光催化活性

利用酸催化的溶胶-凝胶法制备了纯TiO₂和Gd³⁺(0.5wt%)掺杂的TiO₂纳米粉体，采用XRD、BET、XPS、紫外-可见漫反射谱(DRS)和表面光电压谱(SPS)等技术进行了表征；以亚甲基蓝(MB)的光催化降解为探针反应，评价了其光催化活性；探讨了Gd³⁺掺杂对TiO₂纳米粉体的光催化活性的影响机制。结果表明，TiO₂/Gd₂O₃纳米粒子对MB溶液的光催化活性提高到纯TiO₂的1.5倍。掺杂Gd³⁺可以强烈抑制TiO₂由锐钛矿相向金红石相的转变；阻碍TiO₂晶粒的生长；提高高温组织稳定性，改善粉体的表面织构特性；形成光生电子的浅势捕获陷阱，抑制e^-/h⁺复合，这些因素共同作用最终导致TiO₂/Gd₂O₃纳米粉体的光催化活性明显提高。XPS分析结果证实，掺杂Gd³⁺导致粉体的表面羟基含量降低。由于产生了量子尺寸效应，复合粉体的紫外吸收带边蓝移，光的吸收能力略有降低。     

阳极氧化法制备TiO2纳米管及其光催化性能

纳米TiO₂对诸多环境污染物有显著的光催化降解作用,光催化已发展成为新型环境污染治理技术。本文采用阳极氧化法制备出TiO₂纳米管,对比了四种电解液组成(A氟化铵+硫酸铵+水;B氟化铵+硫酸铵+乙酸+水;C氟化铵+硫酸铵+甘油+水;D氢氟酸+二甲基亚砜(DMOS)+乙醇)对催化剂表面形貌及光催化性能的影响。结果表明,电解液A和C都制备出了形貌清晰的TiO₂纳米管,管径约为60~74 nm。样品经400 ℃煅烧,TiO₂晶型主要为锐钛矿相;经500 ℃煅烧,出现少量金红石相;经700 ℃煅烧,晶型全部为金红石相。具有良好形貌的TiO₂纳米管同时具有良好的紫外光吸收能力。当亚甲基蓝初始浓度为10 mg·L^-1,经500 ℃煅烧的TiO₂纳米管光催化活性最佳,光照30 min亚甲基蓝的降解率达89.98%。亚甲基蓝光催化降解反应符合一级反应动力学,反应速率常数为0.079 30。     

Cu掺杂TiO2及其纳米管的制备、表征与光催化性能

通过溶胶-凝胶法和水热法制备了Cu掺杂TiO₂纳米粉末及其纳米管,并通过XRD、TEM、FE-SEM、EDS、UV-Vis/DRS等手段分析了样品的结构。发现以Cu掺杂TiO₂纳米粉末为水热反应原料制备的纳米管中不含Cu,对其原因进行了分析讨论并通过Zn掺杂TiO₂纳米粉末证实：以金属掺杂TiO₂纳米粉末为原料,通过水热法制备TiO₂纳米管中不含有相应金属离子,这是由于金属离子在强碱水热条件下形成金属配离子,使金属离子溶解于水中而不能形成金属掺杂TiO₂纳米管。对所得样品进行了光催化性能测试,发现：Cu掺杂TiO₂粉末的光催化产氢效率为0.75 μmol·(g·h)^-1,高于由其本身及P25通过水热法制备的TiO₂纳米管(分别为：0.42 μmol·(g·h)^-1,0.25 μmol·(g·h)^-1)的光催化产氢效率。     

Ce掺杂Bi2MoO6/TiO2纳米纤维异质结的制备及可见光催化性能

以静电纺丝技术制备的TiO₂纳米纤维为基质,通过溶剂热法制备了异质结型稀土Ce掺杂Bi₂MoO₆/TiO₂复合纳米纤维。利用X射线衍射（XRD）、扫描电子显微镜（SEM）、X射线光电子能谱（XPS）、透射电镜（TEM）、紫外-可见漫反射光谱（UV-Vis DRS）以及荧光光谱（PL）等分析测试手段对样品的物相、形貌和光学性能等进行表征。以罗丹明B为模拟有机污染物,研究了样品的可见光催化性能。结果表明：在稀土掺杂样品中,Ce离子进入Bi₂MoO₆晶格,部分取代Bi³⁺,导致晶胞膨胀,晶格畸变,形成缺陷;与TiO₂复合形成异质结,有利于光生电荷的产生、转移和有效分离,从而提高TiO₂纳米纤维的光催化活性。可见光照射180 min,罗丹明B的降解率达到95.1%。经5次循环光催化降解活性基本不变,样品具有良好的光催化稳定性。     

太阳光下高光催化活性Pr-N-P三元掺杂锐钛矿TiO2纳米片

利用溶胶-凝胶和溶剂热联合技术制备了Pr-N-P三元掺杂锐钛矿TiO₂（PrNPTO）纳米片,并采用X射线衍射、透射电镜、N₂吸附、X射线光电子能谱、UV-vis吸收谱和光致荧光光谱分析技术对其进行了表征.当Pr掺杂量为1.75wt%,焙烧温度为550℃时,制得的PrNPTO在可见和紫外光下光催化降解亚甲基蓝（MB）活性最佳.在模拟太阳光照射下,PrNPTO也表现出优越的光催化降解4-氯酚性能（k_app=3.90×10^-2min^-1）,优于未掺杂、单掺杂和双掺杂TiO₂样品,其光活性是P25TiO₂的3.33倍（k_app=1.17×10^-2min^-1）.PrNPTO光活性的提高归因于Pr-N-P三元掺杂增强了紫外和可见光吸收,降低了光生载流子复合,增加了表面羟基以及改善了表面织构特性.在模拟太阳光照射下,PrNPTO光催化效率高且光催化性能稳定,适合于环境净化领域的实际应用.     

RE/TiO2光催化剂的谱学特性与气相光催化性能的研究

采用改进的sol-gel法和浸渍法制备了TiO₂掺杂稀土离子La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺、Pr³⁺的RE/TiO₂光催化剂,运用FTIR、XRD、TEM、低温氮吸附/脱附、TG/DTA、UV-Vis DRS、表面光电压谱(SPS)等进行表征,以气相光催化降解乙烯、溴代甲烷作为探针反应,阐明了RE/TiO₂光催化剂的谱学特性与气相光催化性能的关系。结果显示,稀土离子掺杂后,TiO₂的锐钛矿含量增加,比表面积增大,粒径变小,吸收边发生蓝移,表面光电压的响应阈值增大,此外,Pr³⁺除外的其它稀土离子掺杂的TiO₂的表面光电压信号增强;光催化降解实验表明,与纯TiO₂相比,La³⁺、Y³⁺、Gd³⁺、Er³⁺、Nd³⁺掺杂TiO₂样品上乙烯、溴代甲烷的光催化活性均有不同程度的增强,而且表现出较强的矿化能力。但是,掺杂Pr³⁺的TiO₂的光催化性能降低恰好对应较弱的表面光电压信号。所以,本文认为提高光生电子-空穴对的分离效率是改善光催化性能的关键因素。     

氟掺杂TiO2纳米管的可见光催化活性及第一性原理计算

作为光催化技术的核心, 提高TiO₂的光催化活性和对可见光的利用率是当前光催化研究中最重要的研究课题. 为了提高TiO₂纳米管的可见光催化活性, 采用化学气相沉积法对TiO₂纳米管进行了氟掺杂. 扫描电子显微镜(SEM)结果表明退火温度对于TiO₂纳米管的形貌完整性有较大影响, 当样品在550和700 °C下退火, 氟掺杂TiO₂纳米管结构受损; X射线衍射(XRD)分析表明氟掺杂对TiO₂由锐钛矿相转化为金红石相有阻碍作用; X射线光电子能谱(XPS)测试表明化学气相沉积能有效地对TiO₂纳米管进行非金属掺杂, 且该方法安全、操作简单. 氟掺杂TiO₂纳米管对甲基橙有较高的可见光催化降解活性. 第一性原理计算结果表明氟掺杂对TiO₂带隙无显著影响, 费米能级附近的F 2p轨道电子位于价带底部, 与O 2p交联作用较小, 因此对TiO₂光吸收带边影响不大. 氟掺杂能促进表面氧空穴的产生, 增加表面酸度与Ti³⁺, 有利于减少电子-空穴复合率, 从而提高其光催化活性.     

Sonophotocatalytic activity of methyl orange over Fe(III)/TiO2

TiO₂ doped with Fe³⁺ was prepared by an impregnation technique and its sonophotocatalytic activity over methyl orange (MO) was investigated. The Fe/TiO₂ surface presented red shift to longer wavelength, resulting in a lower energy band gap. Fe loading of 0.1 wt% on TiO₂ provided the optimum degradation. The MO degradation rate constant under sonophotocatalytic conditions was 2.5 times higher than under photocatalytic conditions.     

The preparation,characterization, photoelectrochemical and photocatalytic properties of lanthanide metal-ion-doped TiO2 nanoparticles

Lanthanide metal-ion-doped TiO₂ nanoparticles were prepared with hydrothermal method and characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM), inductively coupled plasma (ICP) and fluorescence spectrum. The results showed that a small part of metal ions entered into the lattice of TiO₂ and others adsorbed on the surface of TiO₂. The photoelectrochemical and photocatalytic properties of these lanthanide metal-ion-doped TiO₂ nanoparticles were investigated and the results showed that the photoresponse of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ electrodes were much larger and that of Sm³⁺-doped TiO₂ electrode was a little larger than that of undoped TiO₂ electrode, indicating that the photogenerated carriers were separated more efficiently in Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles than in undoped TiO₂ nanoparticles. The photocatalytic degradation of rhodamine B (RB) was conducted in the suspension of lanthanide metal-ion-doped TiO₂ nanoparticles, and its first-order reaction rate constant (k) and average initial rate (r_ini) were significantly higher in the presence of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles than those in the presence of undoped TiO₂ nanoparticles. The enhanced photocatalytic degradation rate of RB in the presence of Eu³⁺-, La³⁺-, Nd³⁺- and Pr³⁺-doped TiO₂ nanoparticles is attributed to increased charge separation in these systems. The effect of the content of La³⁺ on the reaction parameters (k and r_ini) was also investigated and the result showed that there was an optimal value (ca. 0.5%) of the content of La³⁺ to make the rate constant (k) and average initial rate (r_ini) reach the maxima.     

Facile ion-exchange synthesis of Gd-doped K2Ta2O6 photocatalysts with enhanced visible light activity

One of the well-known ways of increasing the visible light absorption capability of semiconducting materials is cation doping. This study aims to use Gd doping to tailor the bandgap energy of K₂Ta₂O₆ (KTO) for photocatalytic degradation of organic pollutants under visible light irradiation. Accordingly, the parent KTO and Gd-doped KTO with different Gd concentrations (K_2-3xGd_xTa₂O₆; x = 0.025, 0.05, 0.075 and 0.1 mol%) were synthesized by hydrothermal and facile ion-exchange methods, respectively. The powder XRD, FT-IR, SEM-EDS, TEM-SAED, N₂ adsorption-desorption, XPS, UV–Vis DRS, PL and ESR techniques were used to investigate the effect of Gd dopant concentration on the structural and photocatalytic properties of KTO. The photocatalytic activity of these samples was investigated for the photocatalytic degradation of methylene blue (MB) dye in an aqueous solution at room temperature under visible light irradiation. The experimental results show that all Gd-doped KTO samples exhibit enhanced photocatalytic activity compared with parent KTO toward MB degradation. In particular, Gd-KTO obtained by doping of 0.075 mol% shows the highest photocatalytic activity among the Gd-doped samples and the degradation efficiency of MB was 79% after 180 min of visible light irradiation, which is approximately 1.5 times as high as that by parent KTO (53%). In addition, trapping experiments and electron spin resonance (ESR) analysis demonstrated that the hydroxyl radicals (^?OH) have played a crucial role in the photocatalytic degradation of MB. The reusability and stability of Gd doped-KTO with a Gd content of 0.075 mol% against MB degradation were examined for five cycles. Based on the present study results, a visible light induced photocatalytic mechanism has been proposed for Gd0075-KTO sample.     

Investigation of photocatalytic activity of metal-doped TiO2 nanoparticles prepared by Pechini method

M-doped TiO₂ (M = Ag²⁺, Al³⁺, Ce⁴⁺, Nb⁵⁺) with different dopant contents have been prepared by the Pechini method using titanium IV isopropoxide as precursor. The effect of doping concentration on the photocatalytic activity for methyl orange (MO) photodegradation was investigated using UV radiation. The photocatalysts were characterized by surface area, X-ray diffraction and UV–Vis diffuse reflectance spectroscopy. An increase in the photoactivity of TiO₂ nanoparticles was confirmed by MO photocatalytic degradation experiments, when the transition metal ions were incorporated into the semiconductor crystalline lattice, which could be attributed to an increase in the charge separation and reduction of e^?/h⁺ recombination as a function of the substitutional defect generated at very low levels.     

Photo Catalytic Degradation of Azo Dyes over Mn2+ Doped TiO2 Catalyst under UV/Solar Light:An Insight to the Route of Electron Transfer in the Mixed Phase of Anatase and Rutile

Mn²⁺ ion was doped into the TiO₂ matrix and its photocatalytic activity was evaluated for the degradation of a mono azo dye methyl orange (MO) and a di‐azo dye brilliant yellow (BY) under UV/solar light. X‐ray diffraction results revealed the phase transformation from anatase to rutile due to the inclusion of Mn²⁺ ion into the TiO₂ matrix. All the doped catalysts showed a red shift in the band gap to the visible region. The degradation reaction of the dyes was found to be dependent on its structure. It was found that mono azo dye degrades faster than di azo dye under UV/solar light. The rate constant under identical conditions calculated for the degradation of MO is 2.4 times (under UV light) and 4.5 times (under solar light) higher compared to BY. Among the photocatalysts studied, Mn²⁺(0.06 at.%)‐TiO₂ showed higher activity under both UV and solar light illumination. The synergestic effect in the bicrystalline framework of anatase and rutile effectively suppresses the charge carrier recombination and enhances the photocatalytic activity. The degradation reaction was followed by UV‐visible spectroscopy and the photoproducts formed were analyzed by GC‐MS techniques.     

Direct synthesis of Nd3+ doped mesoporous TiO2 and investigation of its photocatalytic performance

Nd³⁺ doped mesoporous TiO₂ samples with different molar ratio of Nd/Ti were synthesized by a sol?Cgel method. The textural and optical properties of the samples were systematical characterized by X-ray diffraction, transmission electron microscopy, N₂ adsorption?Cdesorption isotherms, Fourier transform infrared spectroscopy and UV?CVisible absorbance spectroscopy. It was revealed that Nd³⁺ doping inhibited the phase transformation from anatase to rutile after calcination, and the mesoporous structure of doped samples was still retained with the increase of Nd/Ti molar ratio. The surface area of the samples varied from 137 to 210 m²g^?1 and the average pore size of them ranged between 5.7 and 8.2?nm. The photocatalytic activities of all the samples were evaluated by degradation methyl orange (MO) in aqueous solution as a model reaction under UV light irradiation. The results showed that the doped samples demonstrated a higher photocatalytic activity than the mesoporous TiO₂, and the 3?mol% Nd³⁺ doped mesoporous TiO₂ exhibited the best photocatalytic performance. Meanwhile, a promotion effect of the H₂O₂ added was verified in the degradation of MO.     

Enhanced and suppressed effects of ionic liquid on the photocatalytic activity of TiO2

The effects of a room temperature ionic liquid, 1-butyl-3-methylimidazolium terafluoroborate ([Bmim]BF₄), on the photocatalytic performance of Degussa P25 TiO₂ were investigated. Also, the photocatalysis mechanism was systematically analyzed by conducting different reactive radical trapping experiments. The results showed that photogenerated electrons were the main reactive species involved in the photocatalytic degradation of methyl orange (MO), while ?OH radicals and photogenerated holes played an important role in the photocatalytic decomposition of rhodamine B (RhB). The addition of ionic liquid (IL) could slightly enhance the photocatalytic degradation rate of MO because adsorption of [Bmim]⁺ ions on the TiO₂ surface not only enhanced traping and transfer of photogenerated electrons, but also facilitated adsorption of negatively charged MO. On the contrary, IL suppressed the degradation rate of RhB because [Bmim]⁺ on the TiO₂ surface not only hindered the access of positively charged RhB to TiO₂, but also restricted the diffusion of positively charged holes to the TiO₂/solution interface.     

Design of highly ordered Ag-SrTiO3 nanotube arrays for photocatalytic degradation of methyl orange

Ag-SrTiO₃ nanotube arrays were successfully prepared for the degradation of methyl orange (MO) under ultraviolet irradiation. In order to form highly ordered SrTiO₃ nanotube arrays, the preparation of TiO₂ nanotube arrays by anodic oxidation of titanium foil in different electrolytes was investigated. The selected organic solvents in electrolytes include glycerol, dimethyl sulfoxide and glycol. The results indicate that the morphology of TiO₂ nanotube arrays prepared in glycol containing ammonium fluoride electrolyte is more regular. Then SrTiO₃ nanotube arrays were synthesized by a hydrothermal method using TiO₂ nanotube arrays as the precursor. In order to further improve the photocatalytic activity of SrTiO₃ nanotube arrays, Ag nanoparticles were loaded on SrTiO₃ nanotube arrays by two sets of experiments. The loaded Ag results in an enhancement of photocatalytic activity of SrTiO₃ nanotube arrays. Moreover, the effect of pH on the photocatalytic degradation of MO was also studied.