MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶-凝胶法将TiO2担载在介孔MCM-41分子筛上, 制备了不同TiO2含量的系列TiO2/MCM-41复合材料, 利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征. TiO2的晶型为锐钛矿相, 复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小, TiO2的平均粒径随其担载量的增加而增大. 以罗丹明B的光催化降解为探针反应, 评价了TiO2/MCM-41复合材料的光催化降解活性. 结果表明, 在紫外光照射下, 罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学, 复合材料对罗丹明B的光催化降解活性明显高于商用TiO2 (P-25), 复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

MCM-41分子筛担载纳米TiO2复合材料光催化降解罗丹明B

采用溶胶.凝胶法将TiO2担载在介孔MCM-41分子筛上,制备了不同TiO2含量的系列TiO2/MCM-41复合材料,利用X射线衍射、N2吸附、紫外-可见光谱和透射电镜等方法对其进行表征.TiO2的晶型为锐钛矿相,复合材料的比表面积和孔体积随其中TiO2担载量(复合材料中TiO2与MCM-41的质量比)的增加而减小,TiO2的平均粒径随其担载量的增加而增大.以罗丹明B的光催化降解为探针反应,评价了TiO2/MCM-41复合材料的光催化降解活性.结果表明,在紫外光照射下,罗丹明B在该复合材料上的光催化降解反应遵循一级反应动力学,复合材料对罗丹明B的光催化降解活性明显高于商用TiO2(P-25),复合材料的光催化降解活性由复合材料的吸附能力和所含TiO2的光催化活性共同决定.     

碳含量对C/TiO2复合材料光催化活性的影响

 通过热解单层分散在TiO2表面的蔗糖制得了碳均匀覆盖的C/TiO2复合材料,并采用X射线衍射、紫外-可见漫反射吸收光谱和N2物理吸附等方法对复合材料进行了表征. 以亚甲基蓝和罗丹明B为模型化合物评价了C/TiO2复合材料在紫外和可见光照射下的光催化性能,考察了碳含量对催化活性的影响. 结果表明,光源不同,污染物不同,碳含量不同对催化活性的影响均不相同. 对于考察的三个碳含量的C/TiO2催化剂,在紫外光照射下,前驱体中蔗糖/氧化钛质量比为0.1时制得的C/TiO2光催化降解亚甲基蓝的活性最高,蔗糖/氧化钛质量比为0.2时制得的C/TiO2光催化降解罗丹明B的活性最高; 在可见光照射下,蔗糖/氧化钛质量比为0.05时制得的C/TiO2光催化降解亚甲基蓝和罗丹明B的活性都最高.     

Microwave-assisted Synthesis and Photocatalytic Properties of ZnFe2O4/CNT Nanocompistes

以碳纳米管(CNTs)为模板,硝酸锌和硝酸铁为原料,采用微波法合成了CNTs负载ZnFe2O4纳米粒子(1)的复合材料1/CNTs(2),其结构和形貌经XRD,SEM,TEM和EDS表征.以罗丹明B的光催化降解为探针反应,考察了2的光催化降解活性.结果表明:立方尖晶石结构的1均匀地负载在CNTs表面;在紫外光照射下,罗丹明B的光催化降解反应遵循一级反应动力学;2对罗丹明B的光催化降解活性明显高于1.     

二维六方p6mm有序介孔WO_3-TiO_2复合材料的制备及其可见光光催化性能

以非离子型表面活性剂为模板剂,采用蒸发诱导自组装法制备了一系列不同WO3含量的有序介孔WO3-TiO2复合材料,并表征了其孔结构、形貌、孔隙率、光谱性质及组成.结果表明,该材料呈二维六方p6mm对称和锐钛矿晶相结构;与无序WO3-TiO2复合材料相比,其比表面积(152～154m2/g)更大,孔径更均一(5.3nm),且比纯TiO2的帯隙宽度(3.0eV)更窄.将该WO3-TiO2样品用于可见光光催化降解水相中罗丹明B和2,4-二氯苯氧乙酸的反应中,发现WO3含量适当的有序介孔WO3-TiO2样品的光催化活性比无序的样品和纯TiO2的更高.     

还原石墨烯氧化物/磷酸秘纳米复台物的台成及增强的光催化活性

以石墨烯氧化物和硝酸铋为前驱物、甘油为溶剂,200℃下反应1 h,采用溶剂热方法"一锅煮"合成还原石墨烯氧化物/磷酸铋复合纳米材料.利用扫描电镜、透射电镜、X射线衍射、X射线光电子能谱、表面增强拉曼光谱和紫外-可见光谱对所合成样品的形貌和结构进行表征.以罗丹明B作为降解模型分子,考察了复合纳米材料在紫外光照射下的光催化活性.实验结果表明,复合纳米材料的光催化活性优于磷酸铋.在2 h内,还原石墨烯氧化物/磷酸铋对罗丹明B降解率为87.5%;而同样条件下,磷酸铋对罗丹明B的降解率仅为45.7%.复合材料光催化活性的提高主要归因于石墨烯纳米片高效的电子受体和传输特性能有效促进电子-空穴对的分离,进而提高了复合材料的降解效率.     

水热法合成可见光响应的B掺杂TiO2及其光催化活性

以硼酸和钛酸丁酯为原料,采用水热法一步合成了B掺杂的纳米TiO2. 采用X射线衍射、紫外-可见光谱、透射电镜以及X射线光电子能谱对所得样品进行了表征. 结果表明,该方法制备的B-TiO2具有明显的可见光吸收,并且少量B的掺杂不会对TiO2的晶型和粒径造成很大影响. 掺杂的B以 B - O - Ti 的形式存在,有利于可见光活性的提高. 苯酚的光催化降解反应实验表明,水热法合成的B-TiO2在可见光下具有较好的光催化活性,反应 5 h 后苯酚降解率可达100%.     

g-C3N4/Bi2O2CO32D纳米片复合材料的制备及可见光催化性能研究

采用自组装和化学沉淀法分别制得两种可见光驱动复合材料石墨相氮化碳/碳酸氧铋(g-C_3N_4/Bi_2O_2CO_3).采用X射线衍射光谱(XRD),紫外可见光谱、扫描电镜(SEM)、N_2吸附、电化学阻抗谱(EIS)和X射线光电子能谱(XPS)等分析手段对制备的催化剂进行了表征.结果表明,制备方法对纳米复合材料的晶相、形态及光学性能没有影响,但是影响g-C_3N_4和Bi_2O_2CO_3之间的相互作用力,导致光生电子-空穴对的分离速率存在显著差异.以可见光驱动苯酚和罗丹明B的降解实验为探针反应检测催化剂的光催化性能.实验结果表明自组装法得到的异质结催化剂中相互作用力更强,催化效果最高.O_2-是罗丹明B降解反应的主要活性物种,染料的光敏化、Bi_2O_2CO_3与g-C_3N_4综合效应,导致光生载流子电荷分离效率更高.     

高比表面积CuPc/TiO2纳米管复合材料的制备及其可见光光催化活性

以P25为前驱体,在碱性条件下采用水热法制备了TiO2纳米管(NT),然后通过浸渍法将敏化剂酞菁铜(CuPc)附着于TiO2NT表面,制得可见光响应的CuPc/TiO2NT复合光催化材料,并对其进行了表征,考察了它在可见光下降解罗丹明B的光催化活性.结果表明,在NaOH碱性条件下水热法制备的TiO2NT具有较大的比表面...     

Ag@AgI/Ni薄膜的制备及其模拟太阳光催化性能

采用电化学方法制备Ag@AgI/Ni表面等离子体薄膜催化剂,使用扫描电镜（SEM）,X射线衍射（XRD）和紫外-可见漫反射光谱（UV-Vis DRS）对薄膜的表面形貌、晶体结构、光谱特性以及能带结构进行分析表征,在模拟太阳光照射下,把罗丹明B作为模拟污染物对薄膜的光催化活性与稳定性进行评价,采用向反应体系中加入活性物种捕获剂的方法对薄膜光催化机理进行探究。结果表明：最佳工艺下制备的Ag@AgI/Ni薄膜表面是由附着少量Ag粒子的AgI纳米晶构成。薄膜具有显著的表面等离子共振作用、优异的光催化活性和突出的光催化稳定性。光催化反应60 min,薄膜对罗丹明B的降解率（81.1%）是AgI/Ni薄膜的1.35倍,是TiO₂（P25）/ITO薄膜的1.61倍。在薄膜光催化活性基本保持不变的前提下可循环使用5次。薄膜表面纳米Ag的等离子共振对光阴极反应的活化是光催化性能提高的重要原因。提出了薄膜光催化降解罗丹明B的反应机理。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.