Au-CuO／TiO2催化剂用于CO2中微量H2的脱除

用沉积沉淀法制备了Au-CuO/TiO2催化剂和Au/TiO2催化剂,考察了沉淀温度、沉淀pH、焙烧温度和Cu/Au摩尔比等制备工艺条件对Au-CuO/TiO2催化剂性能的影响,确定了适宜的催化剂制备工艺条件.结果表明,Au-CuO/TiO2催化剂对CO2中微量H2的脱除具有较好的活性和稳定性.还考察了还原和H2S中毒处理先后的顺序对催化剂H2脱除活性的影响.结果表明,Au/TiO2催化剂基本上不受处理顺序的影响,而H2S处理顺序对Au-CuO/TiO2催化剂的性能有较为明显的影响,这说明还原后的Au-CuO/TiO2催化剂形成了Au-Cu合金。     

制备条件对Au/LaCoO_3催化氧化CO性能的影响

采用溶胶-凝胶法制备了钙钛矿型复合氧化物LaCoO_3, 并用沉积-沉淀法(DP法)制备了Au/LaCoO_3催化剂. 考察了制备条件对催化剂催化氧化CO活性的影响. 结果表明, 制备过程中, 溶液pH、 pH调节顺序及催化剂焙烧温度对催化剂活性均有一定影响. Au/LaCoO_3催化剂的最佳制备条件为: 沉积过程中在HAuCl4溶液中先加入载体后, 再调节溶液pH=8, 得到的催化剂经250 ℃焙烧后可提高催化剂稳定性.     

不同晶相TiO2负载Au催化剂用于巴豆醛选择性加氢

以不同晶相的TiO2为载体,利用沉积.沉淀法制备了Au/TiO2催化剂,并将其用于巴豆醛选择性加氢反应,考察了TiO2晶相和还原温度对Au/TiO2催化剂性能的影响.结果表明,锐钛矿比金红石更有利于提高巴豆醇选择性,而复合相TiO2载体既可增加Au的催化活性,又可提高巴豆醇选择性.此外,高温还原能促进Au/TiO2催化剂对C=O的选择性加氢,当还原温度为500℃时,产物中巴豆醇是丁醛的2.7倍.     

丙烯气相直接环氧化Au/TiO2催化剂的研究

在H2和O2共存条件下，金催化剂催化丙烯气相直接环氧化反应是近年来发展起来的一种新型环氧丙烷(PO)合成技术．本文采用沉积沉淀法制备了一系列Au／TiO2催化剂，考察了反应溶液的pH值、Au负载量、沉淀剂以及焙烧温度等因素对催化剂丙烯环氧化催化性能的影响．结果表明制备条件对催化性能有明显影响：反应溶液的pH值为7．5及Au负载量为2．4％时所得催化剂活性最好；当以Na2CO3、NaOH等含Na^ 物质作为沉淀剂时，催化性能明显优于Li^ 、K^ 等其它碱金属离子；400℃焙烧制得的催化剂活性较好，在50℃低温反应条件下，环氧丙烷得率可达1．3％．HRTEM结果表明，催化剂中Au组分高度分散于载体表面，且随着焙烧温度的增加Au粒因发生聚集而变大，从而影响了催化剂的活性．表面XPS分析证实，活性较好的Au／TiO2催化剂中活性组分Au除部分呈氧化态外，主要是以金属态的形式存在．     

Au/CeO2催化剂的制备及其对CO催化氧化性能的研究

采用水溶液沉淀法和沉积-沉淀法分别制备了CeO2载体及相应Au/CeO2催化剂,以CO氧化反应为表征反应,考察了载体制备条件,催化剂的焙烧温度、预处理温度和气氛以及活性组分负载量对催化剂性能的影响,并对催化剂进行了BET、XRD和TEM表征,分析了影响催化剂活性的原因.结果表明,载体的制备条件对催化剂的活性有一定影响,经微波处理的载体负载活性组分后,由于活性组分和载体的接触较紧密,因此有利于催化剂活性的提高.催化剂的最佳焙烧温度为300℃,最佳活化温度为300℃,气氛为空气,最佳金负载量为4%.     

Au/Al2O3催化剂的制备及其在CH4/CO2重整反应中的催化活性

采用浸渍法和沉积－沉淀法制备了四种不同的Au/Al2O3催化剂，测定了它们在氢气还原前后及催化反应后的金含量及比表面积，结果表明，制备方法明显影响催化剂的金含量，应用X－光粉末衍射技术研究了这些催化剂经还原处理及反应后的物相变化，金以Au^0物相存在，没有发现氧化态的金物相，考察了该催化剂在CH4／CO2重整反应中的催化活性，发现金催化剂的活性取决于金粒子的大小，浸渍法制备的金催化剂具有较大的金晶粒尺寸，催化活性低，沉积－沉淀法制备的金催化剂金晶粒尺寸较小，催化活性较高，以尿素为沉淀剂制备的催化剂给出1073K时的CH4和CO2转化率分别为8．1％和17．6％，高温反应不仅导致金晶粒的聚集，而且存在明显的金流失现象。     

Ce改性的Pt/γ-AlO3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-AlO3对于富氢气氛下CO选择氧化反应的催化行为考察了制备条件（共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度）对催化活性的影响．结果表明，在80℃时用共沉积沉淀方法制备的催化剂Pt/γ-AlO3-CP-80对CO氧化反应表现出良好的活性和选择性，CO转化率在120℃时可以达到85％．利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征，分析了Cc的促进作用．     

丙烯环氧化反应用Au／TiO2系列催化剂的制备与表征

 用沉积－沉淀法制备了Au／TiO2系列催化剂，并用XRD，TG－DTA，BET，TEM和IR等技术对催化剂的物相、组成和表面结构进行了表征，利用微反对催化剂在丙烯环氧化反应中的活性进行了评价．结果表明，Au／TiO2催化剂的比表面积在100m2／g以上，Au粒子以纳米级超细颗粒均匀分散在锐钛矿型TiO2的表面．催化剂表面的活性相是Lewis酸位Tin＋与Au粒子，Au可以吸附氢与氧并将其转化为过氧化物．在50～150℃温度范围内，丙烯的转化率为0．56％～1．16％，环氧丙烷的选择性在87％以上．原料气中H2或O2的含量增大时，丙烯的转化率随之升高．在催化剂中引入碱金属或碱土金属的硝酸盐作为助剂，可以不同程度地提高催化剂的活性．     

预处理条件对Au/ZnO催化剂CO氧化性能的影响

采用沉积沉淀法制备了用于CO氧化的Au/ZnO催化剂, 并用程序升温还原(TPR), X射线衍射(XRD)和透射电镜(TEM)技术对催化剂进行了表征. 结果表明: 采用沉积沉淀法可制备出高度分散的Au/ZnO催化剂; 提高焙烧温度导致金颗粒聚集长大, 样品经533, 673, 773 K焙烧后金物种的颗粒尺寸分别为2.7, 3.5, 3.7 nm. 催化剂的TPR表征结果中发现部分还原态的金物种在室温就可被氧化, 催化剂预先用流动空气处理可提高其氧化还原性, 样品经多次氧化还原循环后, 其氧化循环性能没有明显下降. CO的氧化反应结果表明, 焙烧温度强烈影响催化剂对CO的氧化活性, 533 K焙烧后的催化剂活性最高. 即使在反应气中含水3.1%(体积比)的湿气条件下, 反应300 h后, CO的转化率仍然保持在95%.     

Ce改性的Pt/γ-Al2O3催化剂用于富氢气氛下CO选择氧化

研究了Ce改性的Pt/γ-Al2O3对于富氢气氛下CO选择氧化反应的催化行为.考察了制备条件(共沉积沉淀法、分步沉积沉淀法以及沉积沉淀温度)对催化活性的影响.结果表明,在80℃时用共沉积沉淀方法制备的催化剂Pt-Ce/γ-Al2O3-CP-80对CO氧化反应表现出良好的活性和选择性,CO转化率在120℃时可以达到85%.利用氢气程序升温还原和原位漫反射红外光谱对不同条件下制备的催化剂进行了表征,分析了Ce的促进作用.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.