介孔分子筛V-MCM-41的水热法制备与合成机理

 以十六烷基三甲基溴化铵为模板剂,廉价的工业级高模数比(3.3)的硅酸钠为硅源,通过水热法合成了V-MCM-41介孔分子筛. 考察了合成条件对产物织构的影响,并采用低温氮吸附法分析探讨了介孔分子筛V-MCM-41的合成机理. 结果表明,模板剂用量、 pH值、加料方式、晶化温度、晶化时间、陈化时间和焙烧气氛等合成条件对介孔分子筛的制备均有影响,其中晶化温度、 pH值和模板剂用量的影响最为明显. X射线衍射谱表明合成的介孔分子筛具有六方晶体结构. 红外光谱和紫外可见光谱表明V进入了介孔分子筛的骨架结构.     

MCM—41介孔分子筛合成研究：Ⅰ.水热合成法

以十六烷基三甲基溴化铵为附加试剂合成了ＭＣＭ－４１介孔分子筛,并用ＸＲＤ,ＳＥＭ和ＩＲ等表征手段考察了晶化时间、晶化温度、物料组成和附加试剂用量等对其晶化过程的影响。结果表明,ＭＣＭ－４１介孔分子筛的晶化诱导期较长,在晶化后期存在着转晶现象,而且有一较适宜的晶化温度,物料组成和附加试剂用量范围。     

以一种新型Gemini表面活性剂作为介孔模板剂通过转晶过程合成介孔ZSM-5分子筛

将一种新型Gemini表面活性剂,丙撑基双(十八烷基二甲基氯化铵)[C18H37(CH3)2–N+–(CH2)3–N+–(CH3)2C18H37]Cl2(C18-3-18),作为介孔模板剂用于水热法合成介孔ZSM-5分子筛.结果表明,在130 oC低温晶化即可高效合成介孔ZSM-5分子刷.C18-3-18的加入量可影响到所合成介孔ZSM-5分子筛的相对结晶度和织构性质,它的形成遵从一个转晶过程.在合成初期,凝胶中介孔模板剂C18-3-18的使用导向了介孔材料的生成;随后在TPABr的模板作用下,介孔材料慢慢转晶生成具有MFI结构的介孔ZSM-5;然后所合成的介孔ZSM-5晶粒进一步长大并聚集形成块状颗粒,同时产生晶间介孔.C18-3-18作为介孔导向剂不仅可用于合成介孔ZSM-5分子筛,也可用于其它介孔分子筛的合成中.     

无外加酸体系中高温合成Al-SBA-15

在无外加酸的体系中,以三嵌段共聚物P123为模板剂,一步合成有序介孔材料Al-SBA-15。考查了高温和硅/铝源物种共水解对产物形貌和结构性质的影响。XRD,N2吸附脱附,IR,SEM,TEM等结果表明,在无外加酸的体系中,升高晶化温度至423 K促使Al-SBA-15的短棒状颗粒分散、卷曲成环状。与较低晶化温度下得到的样品对比,孔径增大,比表面积明显降低。当晶化温度低于423 K,样品铝含量基本保持不变。研究还发现,硅源/铝源物种共水解时间超过20 h后,所得样品中铝含量明显降低。     

不同KIT-6老化温度制备的介孔MnO_2孔径对其催化氧化乙醇的影响（英文）

乙醇既是一种被广泛使用的溶剂,也大量存在于乙醇燃料车尾气中.它是一种挥发性有机化合物(VOCs),能直接参与光化学反应影响空气质量,因此去除乙醇很有必要.催化氧化法消除VOCs是很有前景的技术,其关键是催化剂的制备和筛选.目前,用于乙醇催化氧化的催化剂主要是贵金属催化剂(Pt,Pd,Rh,Au,Ag)和金属氧化物催化剂(Cu,Mn,Co,Fe),此外,还有一些钙钛矿型催化剂.MnO_2具有多种结构(α,β,γ和δ)和形貌(管状,棒状,球状和孔状等).不同形貌和结构的MnO_2具有不同的VOCs催化氧化性能.我们已经报道了介孔MnO_2,特别是三维有序介孔MnO_2,具有良好的乙醇催化氧化活性,有一定的应用前景.然而,KIT-6老化温度对介孔MnO_2孔径的影响,以及MnO_2孔径对催化氧化乙醇活性的影响尚不清楚.如果通过调整KIT-6老化温度改变介孔MnO_2的孔径,很有可能改善催化剂低温还原性,氧物种和活性位等,进而提高其催化性能.本文以40,100和150°C老化合成的KIT-6介孔硅为硬模板,制备出不同的介孔MnO_2催化剂,分别记作Mn-40,Mn-100和Mn-150,用于乙醇氧化反应中,讨论了催化剂孔径对其活性的影响.采用X射线粉末衍射(XRD),氮气吸附-脱附(BET),扫描电子显微镜(SEM),氢气程序升温还原(H2-TPR),氧气程序升温脱附(O2-TPD),X射线光电子能谱(XPS)等技术对催化剂进行了表征.XRD广角结果表明,各催化剂均具有软锰矿型MnO_2晶相,其中Mn-40催化剂存在少量Mn2O3晶相.XRD小角和SEM结果表明,各催化剂均为介孔材料,Mn-100催化剂的有序度和对称性最好,KIT-6老化温度的改变使Mn-40和Mn-150的有序度和对称性降低.BET结果表明,Mn-40,Mn-100和Mn-150分别具有三孔,双孔和单孔体系.随着KIT-6老化温度的降低,KIT-6的孔径降低,而介孔MnO_2催化剂的孔径增加.XPS结果表明,Mn-40因少量Mn2O3晶相的存在而具有较多的Mn3+阳离子和表面晶格氧物种,能增加催化剂氧空位的数量,有利于氧物种的吸附,活化和迁移,从而增强催化活性.TPR和TPD表明,Mn-40催化剂具有良好的低温还原性,它的氧物种容易在低温下脱附并参与氧化反应.催化剂活性测试结果表明,随着介孔MnO_2催化剂的孔径增加,其活性增加.催化剂孔径和活性从大到小的顺序为Mn-40Mn-100Mn-150.以老化温度为40 oC的KIT-6模板制备的Mn-40催化剂,具有较高的乙醇转化频率(TOF),120 oC的TOF为0.11 s.1.Mn-40催化剂具有良好的乙醇氧化催化活性归因于较大孔径,其孔径呈三孔体系分布,最大孔径分布在1.9,3.4和6.6 nm处,三孔体系的形成是因为催化剂孔道的对称性和有序度降低.此外,Mn-40催化剂具有良好的乙醇氧化催化活性也归因于由较多Mn3+阳离子引起的较多表面晶格氧物种和氧空位以及较好的低温还原性     

无外加酸体系中高温合成Al-SBA-15

在无外加酸的体系中,以三嵌段共聚物P123为模板剂,一步合成有序介孔材料Al-SBA-15。考查了高温和硅/铝源物种共水解对产物形貌和结构性质的影响。XRD,N₂吸附脱附,IR,SEM,TEM等结果表明,在无外加酸的体系中,升高晶化温度至423 K促使Al-SBA-15的短棒状颗粒分散、卷曲成环状。与较低晶化温度下得到的样品对比,孔径增大,比表面积明显降低。当晶化温度低于423 K,样品铝含量基本保持不变。研究还发现,硅源/铝源物种共水解时间超过20 h后,所得样品中铝含量明显降低。     

多级复合孔硅铝材料的合成与表征

采用表面包覆聚电解质的聚苯乙烯小球为模板,制备多级复合孔硅铝材料前体。 经水热晶化处理后焙烧脱模板,获得了多级孔结构的硅铝分子筛材料。 通过X射线衍射、傅里叶红外光谱、N2吸附-脱附、扫描电子显微镜和透射电子显微镜等测试技术对水热晶化不同时间的硅铝材料进行表征。 探讨了水热晶化时间对材料孔道结构的影响。 结果表明,水热晶化时间小于22 h,样品中含有介孔-大孔双连续孔道体系。 晶化时间超过22 h,样品中含有微孔-介孔-大孔多级孔道体系。 晶化36 h的样品,大孔孔壁由纳米级ZSM-5型沸石分子筛晶体构成。     

MCM-48介孔分子筛的合成研究

利用水热法合成了ＭＣＭ－４８介孔分子筛,通过ＩＲ,ＴＧ－ＤＴＡ,ＸＲＤ,ＴＥＭ,Ｎ２吸附等方法对产物进行了表征,并系统地研究了晶化温度、晶化时间、凝胶组成等对合成ＭＣＭ－４８介孔分子筛的影响     

氧化钨介孔材料的制备与表征

以介孔二氧化硅(KIT-6)为硬模板, 硅钨酸为钨源, 用硬模板法制备WO3-SiO2复合材料, 再利用HF除去二氧化硅, 得到了介孔三氧化钨材料. 用X射线衍射(XRD)、能量扩散X射线(EDX)、高分辨透射电镜(HRTEM)、N2吸附-脱附等表征手段, 对制备复合材料的物料比、煅烧温度以及不同分散剂等条件进行了考察. 结果表明, 硅钨酸与硅介孔的物料比(m(WO3)/m(SiO2))在3:1到4:1之间, 在600-750 ℃下煅烧, 能制备结构较好的介孔氧化钨. 乙醇和蒸馏水为分散剂时, 用乙醇为分散剂所得的介孔WO3材料具有更高的比表面积和孔体积.     

由纳米晶前驱体组装有序介孔silicalite-1分子筛（英文）

采用两步法将不同尺寸的silicalite-1分子筛纳米晶种通过自组装合成了一系列有序介孔silicalite-1分子筛.首先将强碱性的silicalite-1前驱体分别加热不同时间得到纳米晶种,然后在类似合成SBA-15的强酸性条件下组装成有序的介孔材料.合成条件的剧烈变化阻止了分子筛晶种的继续长大,并在三嵌段共聚物模板的诱导下组装成有序介孔材料.这种"自下而上"的方法制备有序介孔分子筛同时包含微孔和介孔.氮气吸脱附结果表明所制备的介孔分子筛材料均表现了很大的比表面积(730 m2/g以上).     

Synchronous multilayered adsorption of macrocations and macroanions on colloidal spheres. Influence of foreign salt and basicity or acidity of the macroions

The influence of foreign salt, the basicity or the acidity of macroions and the equivalency of the number of ionic groups of macrocations and macroanions upon alternate multiple adsorption on surfaces of colloidal silica (CS91, 110 nm in diameter) and polystyrene spheres (D1A19, 220 nm) have been studied by electrophoretic light scattering measurements. The macrocations used were poly(4-vinyl-N-n-butyl pyridinium bromide (C4PVP, strongly basic), poly(4-vinyl-N-ethyl pyridinium bromide (C2PVP, strongly basic) and poly(allylamine) (PAL, weakly basic). Sodium poly(styrene sulfonate) (NaPSS, strongly acidic) and sodium polyacrylate (NaPAA, weakly acidic) were used as macroanions. The alternate adsorption disappears even in the presence of a small amount of sodium chloride. The alternate multiple adsorption takes place on the addition of C4PVP first and NaPSS next, PAL first and NaPAA next, NaPAA first and C4PVP next, and NaPAA first and PAL next on the CS91 spheres. The influence of the equivalency of the number of ionic groups of C2PVP and NaPAA has been studied for the adsorption on the D1A19 spheres. The synchronous delicate balancing of the electrostatic interactions among the macrocations, the macroanions and the surfaces of the colloidal spheres is important for the alternate multiple adsorption.     

Phase behavior of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) and polyelectrolyte NaPAA

The phase behavior of aqueous mixtures of gemini surfactant hexylene-1,6-bis(dodecyldimethylammonium bromide) (12-6-12) and oppositely charged polyelectrolyte sodium polyacrylate (NaPAA) has been studied experimentally. Compared to the mixtures of the traditional surfactant dodecyltrimethylammonium bromide (DTAB) and NaPAA, the gel phase region in the 12-6-12/NaPAA solution is larger. Element analysis reveals that NaPAA in the gel phase tends to replace the counterions of surfactant micelle and to release its own counterions. Spherical aggregates are observed in either top or bottom gel phase as detected by transmission electron microscopy. The addition of sodium bromide (NaBr) leads to a decrease in the gel phase region and the occurrence of a new cream phase.     

Synthesis of submicrometer-sized titania spherical particles with a sol-gel method and their application to colloidal photonic crystals

A synthetic method for preparing submicrometer-sized titania particles is proposed, which is based on hydrolysis of titanium alkoxide with the use of a cosolvent and an amine catalyst for alkoxide hydrolysis. The preparation was performed with different amines of ammonia, methylamine (MA), and dimethylamine (DMA) in different solvents of ethanol/acetonitrile, ethanol/methanol, ethanol/acetone, ethanol/acetonitrile, and ethanol/formamide for 0.1-0.3 M water and 0.03 M titanium tetraisopropoxide (TTIP) at temperatures of 10-50 degrees C. The use of the ethanol/acetonitrile solvent with MA was required for preparing monodispersed, spherical particles. The number average of the titania particle sizes and their coefficient of variation were varied from 143 to 551 nm and from 5.7 to 20.6%, respectively, with reaction temperature and concentrations of water and MA. Colloidal crystals of titania particles fabricated with a sedimentation method revealed reflection peaks attributed to Bragg's diffraction. Annealing at 100-1000 degrees C led to shrinkage and crystallization of titania particles followed by an increase in the refractive index of titania particles.     

Adsorption of sodium polyacrylate in high solids loading calcium carbonate slurries

The adsorption of sodium polyacrylate (NaPAA) in slurries with up to 75 wt.% calcium carbonate was investigated with the use of attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR) and adsorption of probe molecules. Analysis of the IR spectra demonstrated that the carboxylate groups of NaPAA adsorbed onto ground calcium carbonate (GCC) in three different modes. These modes were shown to be dependent on the solids loading and age of the slurry. Further investigation lead to the determination of the chelating ability of NaPAA at high solids loading.     

Tunable Viscoelastic Properties of Sodium Polyacrylate Solution via CO2-Responsive Switchable Water

Upon stimulus by CO₂, CO₂-switchable viscoelastic fluids experience a deliberate transition between non-viscous and highly viscous solution states. Despite attracting considerable recent attention, most such fluids have not been applied at a large- scale due to their high costs and/or complex synthesis processes. Here, we report the development of CO₂-switchable viscoelastic fluids using commercially available sodium polyacrylate (NaPAA) and N,N-dimethyl ethanol amine (DMEA)-based switchable water. Upon bubbling CO₂, into the solutions under study, DMEA molecules are protonated to generate quaternary ammonium salts, resulting in pronounced decreases in solutions viscosity and elasticity due to the influence of increased ionic strength on NaPAA molecular conformations. Upon removal of CO₂ via introduction of N₂, quaternary salts are deprotonated to tertiary amines, allowing recovery of fluid viscosity and elasticity to near the initial state. This work provides a simple approach to fabricating CO₂-switchable viscoelastic fluids, widening the potential use of CO₂ in stimuli-responsive applications.     

Novel Phenomena of Crystallization and Emulsification of Hydrophobic Solute in Aqueous Solution

Emulsification of lauric acid in an aqueous ethanol solution including lauric acid solute has been observed during cooling before crystallization of lauric acid occurs. The nature of two different solubility curves was explained for the system of lauric acid and aqueous ethanol solution. The mutual solubility of the two liquid phases controls emulsification; the solid solubility of lauric acid controls crystallization. The mutual solubility curve appears at relatively high temperature, and the solid solubility curve at relatively low temperature. Crystallization essentially generates a solid metastable zone under the solid solubility curve. A supersaturated solution can be obtained in the metastable zone. However, no nucleation occurs in the metastable zone. The metastable zone, therefore, still caused emulsification at low temperature before crystallization of lauric acid occurred. The hypothetical mutual solubility curve for the aqueous solution including hydrophobic solutes appeared invariably even at low temperature in the metastable zone under the solid solubility. Copyright 2001 Academic Press.     

几种分子筛的转晶和混晶的控制及单一晶体的优化合成

 以六亚甲基亚胺作模板剂，在配料比一定的情况下，详细考察了反应温度和反应时间对MCM－22，ZSM－5，ZSM－35和丝光沸石分子筛成晶的影响．结果表明，MCM－22的最佳合成温度在低温区，ZSM－35易在提高反应温度或延长反应时间时形成，而作为中间相的ZSM－5和丝光沸石则在反应温度与反应时间合理匹配时才能以单一相生成．同时，探讨了晶种的加入对产物晶相的影响．在特定的温度和时间区间，能够合成出比例可控的ZSM－35＋MCM－22混晶，ZSM－5＋ZSM－35混晶和ZSM－35＋丝光沸石混晶，并从分子筛孔道和结构单元的特点出发，就转晶发生对温度和时间的依赖性作了解释．     

低硅SAPO-34分子筛的复合模板剂法合成及其对甲醇制烯烃的催化性能

系统考察了模板剂比例和晶化条件对复合模板剂(三乙胺+四乙基氢氧化铵)法合成低硅SAPO-34分子筛的影响;评价了合成产物对甲醇制烯烃的催化性能.结果表明,190℃晶化时不易合成低硅SAPO-34分子筛,而170℃晶化、模板剂组成为2Et3N+0.3TEAOH时可合成纯相SAPO-34分子筛.较高温度晶化时,延长晶化时间,SAPO-34有向SAPO-5转晶的趋势,而较低温度晶化时则相反.与晶化3 d的分子筛样品相比,170℃晶化5 d后的分子筛样品的比表面积较大、强酸中心较多、弱酸中心较少、对甲醇制烯烃反应的催化寿命较长.     

The adsorption and desorption of ethanol ices from a model grain surface

Reflection absorption infrared spectroscopy (RAIRS) and temperature programed desorption (TPD) have been used to probe the adsorption and desorption of ethanol on highly ordered pyrolytic graphite (HOPG) at 98 K. RAIR spectra for ethanol show that it forms physisorbed multilayers on the surface at 98 K. Annealing multilayer ethanol ices (exposures >50 L) beyond 120 K gives rise to a change in morphology before crystallization within the ice occurs. TPD shows that ethanol adsorbs and desorbs molecularly on the HOPG surface and shows four different species in desorption. At low coverage, desorption of monolayer ethanol is observed and is described by first-order kinetics. With increasing coverage, a second TPD peak is observed at a lower temperature, which is assigned to an ethanol bilayer. When the coverage is further increased, a second multilayer, less strongly bound to the underlying ethanol ice film, is observed. This peak dominates the TPD spectra with increasing coverage and is characterized by fractional-order kinetics and a desorption energy of 56.3+/-1.7 kJ mol(-1). At exposures exceeding 50 L, formation of crystalline ethanol is also observed as a high temperature shoulder on the TPD spectrum at 160 K.     

盐卤硼酸盐化学XXX-MgO·2B_2O_3-18%MgCl_2-H_2O过饱和溶液结晶动力学

对ＭｇＯ·２Ｂ_２Ｏ_３－１８％ＭｇＣｌ_２－Ｈ_２Ｏ过饱和溶液在不同温度条件下的结晶动力学过程进行测定,给出结晶动力学方程。析出固相采用Ｘ－射线粉末衍射、红外光谱和热分析进行物相鉴定。提出使用结晶法合成章氏硼镁石的新方法。