二氧化钛纳米微粒的制备与光催化活性

本文采用溶液－凝胶法制备了粒径为１０－２０ｎｍ左右的二氧化钛纳米微粒。用ＸＲＤ研究了二氧化钛溶胶的热处理过程,研究表明温度在４７３Ｋ－６７３Ｋ左右ＴｉＯ２向量 粒呈不规整锐钛矿结构,粒径约为１０－２０ｎｍ。在８７３Ｋ左右ＴｉＯ２微粒出现锐钛矿与金红石型混晶结构。     

二氧化钛的尺寸与光催化活性的关系

采用溶胶－凝胶法控制制备了晶粒尺寸从１０ｎｍ到８０ｎｍ的二氧化钛纳米半导体．用光催化降解苯酚作为模型反应，结合ＸＲＤ，ＤＲＳ，ＦＳ等表征手段，研究了纳米ＴｉＯ２的制备条件与其晶粒尺寸和相结构的关系，探讨了纳米ＴｉＯ２尺寸效应对其光催化活性的影响．发现当晶粒尺寸小于１６ｎｍ时，二氧化钛半导体具有了明显的尺寸量子效应．尺寸量子效应对提高ＴｉＯ２光催化降解苯酚的催化活性起了极为重要的作用．     

纳米TiO_2微胶粒的光化反应制备机理及量子尺寸效应

研究了由水相Ｔｉ３＋制备纳米极ＴｉＯ２微胶粒的光化反应机理及反应动力学，给出反应速率方程，讨论了ＴｉＯ２微胶粒的量子尺寸效应，经电镜测试ＴｉＯ２粒子的直径为１５～２５ｎｍ，反应过程中由气相色谱仪监测生成物Ｈ２。     

纳米TiO2微胶粒的光化应制备机理及量子尺寸效应

研究了由水相Ｔｉ＾３＋制备纳米极Ｔｉ＾Ｏ２微胶粒的光化反应机理及反应动力学，给出反应速率方程。讨论了ＴｉＯ２微胶粒的量子尺寸效应，经电镜测试ＴｉＯ２粒子的直径为１５－２５ｎｍ。反应过程中由气相色谱仪监测生成物Ｈ２。     

甲苯气相选择氧化制苯甲醛Ⅲ．V_2O_5／TiO_2催化剂研究

制备了一系列不同Ｖ２Ｏ５负载量的Ｖ２Ｏ５／ＴｉＯ２催化剂并用于甲苯气相选择氧化制苯甲醛．在ＶＴｉ－１０催化剂上，可获得苯甲醛产率１２．０％的最佳结果．利用ＢＥＴ、ＸＲＤ、ＸＰＳ、Ｈ２－ＴＰＲ、Ｏ２－ＴＰＤ－ＭＳ和化学分析法，考察了催化剂的结构和表面氧性质．发现载体ＴｉＯ２上Ｖ２Ｏ５以晶相和高分散态两种形式存在．反应过程中，催化剂中Ｖ４＋和Ｖ５＋可调整到一定比例并趋于稳定，该调整时间约为１００ｍｉｎ．     

溶剂化金属原子浸渍法制备高分散Au/TiO2低温CO氧化催化剂

用溶剂化金属原子浸渍法制备了不同金含量的高分散Ａｕ／ＴｉＯ２催化剂,ＸＲＤ和ＴＥＭ测定结果表明,随着金含量的增加,金颗粒度增大,但直径都在１．８～３．５ｎｍ范围内,ＸＰＳ研究表明上于金属态,Ａｕ／ＴｉＯ２在低温下就显示出较高的ＣＯ知性,３２３Ｋ时ＣＯ的转化率可达到１００％,金颗粒度为１．８ｎｍ的Ａｕ／ＴｉＯ２催化剂活性最高。     

甲苯气相选择氧化制苯甲醛：Ⅱ.V2O5／TiO2催化剂焙烧温度和反应条件探讨

利用ＢＥＴ、ＸＲＤ、Ｈ２－ＴＰＲ，Ｏ２－ＴＰＤ－ＭＳ等测试手段，并结合化学分析方法，研究了焙烧温度对Ｖ２Ｏ５／ＴｉＯ２催化剂结构和性能的影响。同时探讨了Ｖ２Ｏ５／ＴｉＯ２催化剂上较适合于甲苯气相选择氧化的氧浓度和空速。结果表明，催化剂在７７３Ｋ活化，氧浓度７％，空速１４，０００ｈ＾－１时效果较好。     

溶胶—凝胶法制备负载型TiO2膜的研究

本研究采用溶胶－凝胶（Ｓｏｌ－Ｇｅｌ）法制备了负载型ＴｉＯ２膜，并采用ＳＥＭ、压汞等实验手段对Ｔｉ（ＯＨ）４溶胶和ＴｉＯ２膜进行了表征。实验表明：Ｔｉ（ＯＨ）４溶胶制备过程中Ｈ２Ｏ／Ｔｉ＾４＋、Ｃ２Ｈ５ＯＨ／Ｔｉ＾４＋的比值，溶胶在支承管上浸涂的时间、次数以及凝胶煅烧升温速度和煅烧温度均是制备负载型ＴｉＯ２膜的重要因素。最终制得一种无裂纹、２０μｍ厚、孔径分布在５０￣３００ｎｍ之间的负载型ＴｉＯ２     

化学气相沉积法制备的TiO_2薄膜的光学性质及其应用

以ＴｉＣ１４为源物质采用常压化学气相沉积法制备了ＴｉＯ２薄膜。用紫外光谱测定了膜的透过率,进而计算出折光率、消光系数、光学带隙能等光学参数。结果发现,在不同气流量、沉积温度为１００～２５０℃的条件下制备的ＴｉＯ２膜,其折射率在２．１６～２．８２范围内,消光系数在０．０４×１０－３～６．７０×１０－３范围内,光学带隙能在２．８～３．０８ｅＶ范围内。在光催化作用下,ＴｉＯ２膜用于处理苯酚溶液,苯酚的转化率高达５４．０５％。关键词##4化学气相沉积（ＣＶＤ）;;沉积率;;折光率;;消光系数;;光催化     

低温液相合成甲醇及甲酸甲酯用Cu-Cr-M-O催化剂的制备与表征

采用共沉淀法和配合物沉淀法制备了分别添加Ｂａ, Ｍｎ,Ｖ,Ｂｉ,Ｎｉ 和Ｚｎ 的ＣｕＣｒＭＯ三组分催化剂,采用ＢＥＴ,ＸＲＤ和ＴＥＭ 对催化剂进行了表征,并考察了其对合成甲醇及甲酸甲酯反应的活性及选择性． 结果表明,添加第三种金属使催化剂的稳定性及甲酸甲酯选择性有所提高,但使催化活性有所下降． 配合物沉淀法制备的催化剂的比表面积较大,粒径较小． 热分解温度越高,催化剂的比表面积越小． 除ＣｕＣｒＶＯ 催化剂为纳米非晶态之外,其它催化剂均呈晶态． 催化剂的最小平均粒径为３８ ｎｍ , 最大平均粒径为６８ ｎｍ , 属纳米级催化剂．     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.