黑曲霉脂肪酶的耦合固定化及特性

研究了吸附-絮凝耦合的方法固定脂肪酶的工艺条件.结果表明:在33℃下,用0.03mol/L的磷酸二氢钾?氢氧化钠缓冲液控制体系pH为7.0,酶与树脂(质量比1∶8)作用吸附1h后,用0.2mL絮凝剂聚丙烯酰胺(w(PAM)=0.5%)处理,得到活力较高的固定化脂肪酶.固定化酶最适pH9.0,最适温度为45℃,活力为405U/g,酶活回收率可以达到40%.固定化脂肪酶制备简便,可重复使用,稳定性较高.     

无溶剂系统中固定化脂肪酶催化废油脂转酯生产生物柴油

 探讨了无溶剂系统中固定化脂肪酶Novozym 435催化餐饮业废油脂转酯生产生物柴油. 反应副产物甘油可吸附在固定化酶载体表面,采用丙酮洗涤除去甘油可提高酶的稳定性. 适宜的醇/油摩尔比、酶用量、反应温度和摇床转速分别为1, 6.6 U/g, 35～40 ℃和150 r/min,不宜加水到反应体系中. 采用分步加入甲醇的方式可减轻甲醇对酶的毒害作用. 分别在反应进行到6和14 h时用丙酮除去酶表面的甘油,然后按醇/油摩尔比为1的比例加入甲醇继续反应,反应30 h后产物中的脂肪酸甲酯含量为88.6%. 连续反应300 h后,酶活性基本没有下降.     

有机相中固定化脂肪酶催化合成植物甾醇酯

酶法合成植物甾醇酯具有反应条件温和、产物纯度和产量高等优点,但非水相酶催化的活性和稳定性普遍较低.本文以大孔树脂固定化脂肪酶为催化剂,并在催化过程中添加乳糖的类似物,构建了有机相高效合成植物甾醇酯的工艺过程.以酯化率为考察指标,对脂肪酶和反应溶剂进行筛选,对酯化条件进行优化,同时考察了糖的种类及添加量对酶催化性能的影响.结果表明,大孔树脂NKA吸附固定化的褶皱假丝酵母(Candida rugosa)脂肪酶(NKA-CRL)为最适宜的催化剂,以正己烷为反应介质,在酸醇摩尔比为2和添加酶蛋白质量7.5%的海藻糖的条件下,40°C反应10 h,酯化率达到96.6%.连续6次催化后,植物甾醇的酯化率仍维持在85.0%以上.     

基于氯化镁饱和溶液中固定化脂肪酶Lipozyme TL IM催化光皮树油脂合成生物柴油

基于氯化镁饱和溶液反应体系中,对采用固定化脂肪酶Lipozyme TL IM催化光皮树油脂转化为生物柴油的工艺进行了研究。考察了固定化脂肪酶Lipozyme TL IM催化光皮树油转酯化的工艺中甲醇的用量、固定化脂肪酶的添加量、摇床的转速和反应时间对生物柴油产率的影响。实验结果表明,采用氯化镁饱和溶液反应体系,在醇油摩尔比为3∶1,固定化酶Lipozyme TL IM用量为光皮树油质量的20%,摇床转速为150 r/min,反应8 h时,生物柴油产率最高,达到86.5%。与传统的三步甲醇醇解或者有机溶剂反应体系比较,采用的氯化镁饱和溶液体系的酶稳定性更好,反应效率更高,有效地解决了酶在甲醇中失活的问题,生产成本低,可成为生产生物柴油的新工艺。     

纳米-微米复合孔泡沫陶瓷固定化脂肪酶

考察了泡沫陶瓷的孔径分布和表面性质对脂肪酶固定化的影响.研究表明,泡沫陶瓷的纳米孔孔径分布非常适合脂肪酶的固定化,对固定化酶的催化效率有决定性的影响.经1h的定化,泡沫陶瓷固定化酶的活性达商业化硅藻土固定化酶的1.33倍,体积活力为其2.63倍,蛋白载量为45.36mg/g陶瓷,比活为1215.39U/g,活力回收为41.2%.泡沫陶瓷固定化脂肪酶在有机相乙酸乙酯合成中表现优良,连续使用5次,每次反应3h,乙酸转化率均在93%左右.     

固定化脂肪酶催化麻疯树油与碳酸二甲酯制备生物柴油的研究

以介孔硅材料(MPS)为载体将脂肪酶固定化,以碳酸二甲酯为酰基受体,对固定化酶催化碳酸二甲酯进行了反应路径(原料油)、反应条件(反应温度、碳酸二甲酯的用量、加水量)的优化,在最佳的条件下对实验过程中所用的固定化酶进行重复使用性的考察。实验结果表明,不同种油与碳酸二甲酯反应在固定化酶的催化下制备生物柴油的产率以麻疯树油为最高,最佳反应条件是碳酸二甲酯的浓度为16m L/g、不加水,在50℃下反应24h,生物柴油得率达81.6%。     

壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶及其性质

以具柔性亲水手臂的壳聚糖-精氨酸树脂为载体,用戊二醛交联胰凝乳蛋白酶,获得壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶. 最佳固定化条件为:m(酶)∶ m(载体)=20∶ 1 000、戊二醛体积分数为1.0%、pH=5.20、30 ℃交联60 min. 固定化酶活力达850 U/g,Km为1.83 mmol/L,比游离酶增大33.6%,比交联壳聚糖固定化酶低24.0%. 壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶水解时间进程曲线与游离酶基本一致,均在反应30 min达到最大速率,最适温度为70 ℃,比游离酶升高10 ℃;在75 ℃时的半衰期可达6.0 h,比游离酶提高约4.3倍;最适pH值为5.92,比游离酶向酸性偏移2pH单位. 4 ℃贮存半衰期为49 d.     

固定化脂肪酶催化碳酸二甲酯制备生物柴油的研究

以介孔硅材料(MPS)为载体将脂肪酶固定化,以碳酸二甲酯为酰基受体,对固定化酶催化碳酸二甲酯进行了反应路径(原料油)、反应条件(反应温度、碳酸二甲酯的用量、加水量)的优化,在最佳的条件下对实验过程中所用的固定化酶进行重复使用性的考察.实验结果表明,不同种油与碳酸二甲酯反应在同定化酶的催化下制备生物柴油的产率以麻疯树油为最高,最佳反应条件是碳酸二甲酯的浓度为16mL/g、不加水,在50℃下反应24h,生物柴油得率达81.6％.     

以HPD-750大孔树脂为载体材料固定化果胶酶

HPD-750树脂是中极性大孔吸附树脂,生物相容性好,机械性能稳定,具有较大的比表面积,可用于固定化酶载体材料。本文以HPD-750大孔树脂为载体固定化果胶酶,研究各因素对固定化酶的影响,并采用正交试验对固定化条件进行优化。结果表明,当pH为4.0、固定化温度为45℃、固定化时间为4h、加酶量为0.16g/mL时,固定化酶活力可达5146U/mg。以HPD-750大孔树脂为载体材料制备的固定化酶相较于游离酶具有更好的酸碱稳定性和热稳定性。在循环使用10次后,酶活力依然保留80%以上;4℃储藏25d之后,其酶活力仍保留60%以上。与D311大孔树脂、聚丙烯酰胺和海藻酸钠微球制备的固定化酶相比,HPD-750大孔树脂固定化酶的活性、操作稳定性、机械稳定性和储存稳定性都较好。该结果说明,HPD-750大孔树脂可作为固定化酶较好的载体材料。     

粘质沙雷氏菌脂肪酶的固定化及催化拆分反式3-(4’-甲氧苯基)缩水甘油酸甲酯

 对粘质沙雷氏菌脂肪酶进行了固定化研究,确定硅藻土和环氧树脂Eupergit C是较好的固定化载体. 固定化后酶的热稳定性、 pH稳定性及储存稳定性均明显提高. 以Eupergit C共价固定的脂肪酶,其操作稳定性比硅藻土吸附酶好,重复使用10批次后,剩余酶活力还有50%左右,戊二醛交联对Eupergit C固定化酶稳定性的提高没有明显效果,而硅藻土吸附酶经戊二醛交联后稳定性有所提高,经5批次反应后剩余酶活力还有50%. 使用交联后的硅藻土固定化酶(1 g, 200 U), 在两相搅拌反应器(工作体积200 ml, 甲苯∶水体积比=1)中对地尔硫卓手性前体(±)-反式3-(4’-甲氧苯基)缩水甘油酸甲酯((±)-MPGM)(有机相浓度为0.5 mol/L)进行了催化拆分,经5批次反应后,共得纯(2R,3S)-(-)-MPGM 18.6 g, 产品光学纯度(对映体过量)>99%, 总收率为37.2%.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.