纳米羟基磷灰石表面接枝聚合左旋丙交酯

为了改善HA纳米粒子与有机PLGA的相容性,分别采用六亚甲基二异氰酸酯加乙二醇、左旋乳酸改性纳米粒子表面后或直接原位接枝聚合左旋丙交酯等3种不同方法,制备了表面修饰聚乳酸的纳米羟基磷灰石(PLLA-g-HA).FTIR、XPS、TEM、TGA测试表明PLLA成功接枝到HA的表面.其中六亚甲基二异氰酸酯加乙二醇改性HA纳米粒子所获得的PLLA接枝率远高于其它两种方法达25%,调整有机相和无机相的比例对PLLA接枝率的影响较小,其在氯仿中可以稳定分散2天以上.共混电纺丝后的拉伸测试表明PLLA-g-HA/PLAG复合纤维膜的力学性能高于HA/PLGA膜,当两者之间的比例为5%拉伸性能达到最大值.     

含石墨烯的聚乳酸复合纳米纤维的制备及细胞相容性

利用电纺丝技术制备了聚乳酸(PLLA)-石墨烯(Gr)复合纳米纤维.通过SEM、TEM及拉曼光谱观察和分析了该复合纳米纤维的形貌及Gr在PLLA中的分散状态,通过DSC、TG、力学拉伸及接触角测试等表征方法研究了PLLA-Gr复合纳米纤维的热性能、力学性能、亲水性等物理性能,最后,通过MTT法检测一种神经胶质细胞——雪旺细胞(SCs)在该复合纳米纤维支架上的生长和增殖行为,评价其细胞相容性.结果表明:低含量的Gr能较好地分散在PLLA纳米纤维中,且随着m(Gr)∶m(PLLA)从0增加到2.0％,所得到的纤维直径呈现先减小后增加的趋势.当m(Gr)∶m(PLLA)增加到1.0％时,PLLA Gr纳米纤维的直径达到最小,为(0.50±0.19) μm,对应的拉伸强度较未添加Gr时增加也最大达50％.PLLA-Gr纳米纤维膜的结晶度与Gr的含量和分散性有关.细胞培养1、4、7d后的MTT检测结果表明PLLA-Gr复合纳米纤维能促进SCs的黏附和生长.PLLA-Gr复合纳米纤维具有较好的细胞相容性.     

静电纺丝法制备胆固醇-g-聚乳酸液晶/ 聚乳酸复合纳米纤维膜

以辛酸亚锡为催化剂, 胆固醇(CHOL)为共引发剂引发D,L-丙交酯开环聚合, 制备了胆固醇-g-聚(D,L-乳酸)(CHOL-g-PDLLA)低聚物, 采用偏光显微镜(POM)和差示扫描量热(DSC)方法考察了其液晶特性. 通过静电纺丝技术制备了CHOL/PDLLA和CHOL-g-PDLLA /PDLLA复合纳米纤维膜, 对其形貌、界面相容性、孔隙率、拉伸性能和细胞相容性进行了研究. 结果表明, CHOL-g-PDLLA为一种热致胆甾型液晶, 液晶温度区间为21.8~74.5 ℃; CHOL-g-PDLLA/PDLLA复合纳米纤维膜的纤维形态良好, 表面均匀光滑, 孔隙率在70%~75%之间, 且其界面相容性优于相应的CHOL/PDLLA. 随着CHOL和CHOL-g-PDLLA含量的增加, 复合纳米纤维膜的拉伸强度逐渐下降, 但CHOL-g-PDLLA/PDLLA复合纳米纤维膜的拉伸强度显著大于CHOL/PDLLA. 体外骨髓间充质干细胞培养结果显示, CHOL-g-PDLLA/PDLLA复合纳米纤维膜具有良好的细胞相容性, 且优于相应的PDLLA和CHOL/PDLLA纳米纤维膜.     

溶液喷纺法制备聚乳酸/锂藻土复合纳米纤维膜及其性能

为改善聚左旋乳酸(PLLA)的亲水性和生物活性,采用溶液喷纺法将具有良好亲水性和生物活性的锂藻土(LAP)复合到PLLA纳米纺丝膜中。采用扫描电镜(SEM)、傅里叶红外光谱(FT-IR)、万能试验机、接触角测量仪对纤维膜的形貌、化学结构、力学性能和亲水性进行了表征,并研究了纤维膜的降解性能和细胞相容性。结果表明,适量LAP可在PLLA纳米纤维中均匀分布,所得PLLA/LAP杂化纳米纤维直径为200～300 nm。LAP的引入有助于改进PLLA的亲水性,并提高其力学性能,同时可在一定程度上调节PLLA的降解速率。体外生物学评估表明,LAP的引入能提高纳米纺丝膜的细胞增殖效应。     

静电纺丝法制备PAN/HNTs混杂纤维增强热塑性聚氨酯复合材料

静电纺丝方法制备了聚丙烯腈/埃洛石纳米管(PAN/HNTs)混杂纤维增强体,通过改变接收装置、热拉伸处理得到5种不同的PAN/HNTs混杂纤维增强体。采用浸渍法将5种增强体用于改性热塑性聚氨酯,得到PAN/HNTs/TPU复合材料。结果表明,PAN/HNTs混杂纤维增强体可显著提高复合材料的力学性能。将平板接收制备的PAN/HNTs混杂纤维增强体以及另外两种由1050r/m滚筒接收制备的PAN/HNTs混杂纤维增强体(前者不采用热拉伸,后者采用热拉伸),三者制成PAN/HNTs/TPU复合材料。与通过平板接收制备的复合材料相比,通过由1050r/m滚筒接收制备的两种复合材料性能要优于前者,相较于前者,其复合材料的拉伸强度分别增加了19%和43%,弹性模量分别增加了44%和122%,断裂伸长率分别增加了19%和24%。当定向接收的PAN/HNTs纤维膜的含量为5.6%时所得到的PAN/HNTs/TPU复合材料力学性能为最佳;通过热拉伸处理PAN/HNTs纤维膜,当含量为4.5%时,复合材料的力学性能为最佳。这种力学增强的主要原因是PAN/HNTs纤维与热塑性聚氨酯材料之间的相容性得到了改...     

静电纺制备纳米孔结构聚乳酸(PLLA)超细纤维

采用静电纺丝法制备了孔径为40～150 nm的PLLA纳米孔结构超细纤维,纳米孔不仅分布在纤维表面,而且存在于纤维内部.通过扫面电镜观察了纤维表面形貌.探讨了混合溶剂二氯甲烷/N,N-二甲基甲酰胺的比例、PLLA浓度、电场强度对PLLA纤维纳米孔大小、分布密度、深度的影响.结果表明通过调节PLLA溶液性质和纺丝参数,PLLA纤维的表面形貌可以在3种状态即光滑无孔、疏浅凹坑、密集深孔之间可控.二氯甲烷/N,N-二甲基甲酰胺比例为1∶4,PLLA浓度9%,电场强度1 kV/cm,环境温湿度分别为30℃和52%,静电纺丝所得PLLA超细纤维表面孔洞直径为150 nm,孔洞分布密集.纳米孔PLLA纤维形成的主要机理是由于静电纺丝过程中溶剂的快速挥发引起纤维表面温度急剧降低导致热致相分离而产生多孔结构.PLLA纤维膜的疏水性与纤维表面孔洞结构密切相关,纤维膜接触角最高可达146.6°.由于PLLA纤维的多孔结构,这种高疏水性的PLLA纤维膜能够快速、大量地吸油,90 s内吸收柴油达到90 g/g,25 min内可以达到145 g/g.     

MMA接枝改性PVC/CaCO3纳米复合材料的力学性能

采用熔融共混法制备PMMA接枝改性纳米CaCO3增韧PVC（PVC/CaCO3）复合材料,并研究了复合材料的力学性能.结果表明,通过表面PMMA的接枝改性,可以显著提高纳米CaCO3增韧聚氯乙烯复合材料的拉伸强度和拉伸模量,在纳米CaCO3颗粒表面PMMA包覆层厚度为2nm时,复合材料的拉伸强度和拉伸模量达到极大值.对比于未处理纳米CaCO3和钛酸酯偶联剂处理纳米CaCO3,PMMA接枝改性纳米CaCO3增韧PVC复合材料的拉伸强度得到较大幅度提高.SEM显示,经过PMMA接枝改性后的碳酸钙在PVC基体中分散均匀,与基体界面结合良好.     

硬脂酸改性β-TCP的分析测定及其PLLA复合纳米纤维膜性能研究

采用硬脂酸对β-磷酸三钙(β-TCP)进行表面改性,并研究了β-TCP与硬脂酸的界面作用,通过透射电子显微镜(TEM)、热重分析仪(TGA)以及X光电子能谱(XPS)对改性前后β-TCP的形貌、热失重和表面基团进行表征;采用静电纺丝法制备不同质量配比的β-TCP/PLLA和改性β-TCP/PLLA复合纳米纤维膜,用扫描电镜(SEM)观察复合膜的形貌,并研究其力学性能。结果表明,硬脂酸包覆在β-TCP表面,改性后的β-TCP具有一定疏水性,硬脂酸的H+可与β-TCP中PO3-4的1个O发生质子化反应形成—OH;硬脂酸改性减轻了β-TCP微粒的团聚,可以得到连续均匀的纤维,改性后的β-TCP/PLLA复合纳米纤维膜的力学性能较改性前有明显提高。     

AOPAN/PA-66复合纳米纤维膜的制备及对金属离子的吸附性能

采用双喷头电纺丝技术,将尼龙(PA-66)纤维增强的聚丙烯腈(PAN)纳米纤维膜(PAN/PA-66)与盐酸羟胺进行偕胺肟化反应,制备了一种偕胺肟化聚丙烯腈/尼龙复合纳米纤维膜(AOPAN/PA-66).通过红外光谱及扫描电子显微镜等方法研究了偕胺肟化前后纳米纤维膜的组成、形貌和力学性能;并考察了AOPAN/PA-66复合纳米纤维膜对铜离子和铅离子的吸附性能.结果表明,AOPAN/PA-66复合纳米纤维膜的抗拉伸强度及断裂伸长率分别为4.73 MPa和30.76%,对Cu(Ⅱ)及Pb(Ⅱ)的吸附量分别为67.5和75.4 mg/g.     

静电纺丝素/胶原/聚合物复合纤维的制备及其力学性能的研究

目前,将天然高分子蛋白和聚合物共混利用静电纺丝法制作各种组织工程支架材料倍受关注。基于这种研究背景,在本文中利用静电纺丝技术,制备了丝素(SF)/胶原(COL)/聚左旋乳酸(PLLA)和SF/COL/聚左旋乳酸-己内酯(PLCL)两种共混复合纤维膜,通过扫描电镜(SEM)对纤维形态结构分析,发现复合纤维形貌良好,直径较为均一。同时改变纺丝液中高分子蛋白的比例,复合纤维的直径也随之减小。此外,对复合纤维进行了力学性能测试,发现随着聚合物含量的增加,复合纤维膜的力学性能得以改善,SF/COL/PLCL组复合纤维的拉伸性能明显优于SF/COL/PLLA组。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.