聚乳酸接枝改性纳米生物玻璃/PLGA复合材料的制备、表面性质及生物活性

以丙交酯开环聚合原位接枝改性的纳米生物玻璃(PLLA-g-BG)与聚丙交酯-乙交酯(PLGA)复合材料为研究对象, 采用TGA, ESEM和EDX分析其接枝率, 粒子分散性和表面元素分布, 通过将兔成骨细胞种植于材料膜表面进行体外培养, 采用荧光染色法、NIH Image J图像分析软件、MTT法和流式细胞术等手段检测细胞在材料表面的平均黏附数量、扩展面积比、增殖能力和细胞周期的变化, 综合评价新型改性纳米复合材料的生物相容性和生物活性. 结果表明, 聚乳酸表面接枝改性可明显改善纳米生物玻璃粒子的团聚; PLGA中掺入一定比例的改性PLLA-g-BG可明显促进兔成骨细胞的黏附、扩展与增殖; 改性纳米生物玻璃的应用可提高生物可降解聚酯材料的生物相容性和生物活性.     

静电纺丝法制备PLLA/g-HNTs复合纳米纤维膜及其性能研究

以辛酸亚锡为催化剂,利用HNTs表面的羟基引发L-LA开环聚合,合成了表面接枝聚(L-乳酸)(PLLA)链段的埃洛石纳米管(g-HNTs),通过红外、热失重和透射电镜对改性前后HNTs的组成与形貌进行了观察;然后采用静电纺丝技术制备了PLLA纳米纤维膜以及不同组成的PLLA/HNTs和PLLA/g-HNTs复合纳米纤维膜,探讨了纺丝条件对纳米纤维膜形貌的影响,并对复合膜的组成、形貌、力学性能和细胞相容性进行了研究.结果表明,当HNTs与L-LA的摩尔投料比为1∶10时,g-HNTs表面PLLA链段的接枝率为14.22％,HNTs纳米管的形态在接枝后变化不大,易于在无水乙醇中分散.电压强度和进样速率对纤维膜的形貌有一定影响,当电压强度为15 kV、进样速率为1 mL/h时,电纺纤维的直径较为均匀.复合纤维膜中g-HNTs在基体PLLA中的分散性以及与基体的界面相容性要优于相应的HNTs,当g-HNTs含量高达40％时,复合纳米纤维膜中的纤维形态仍然保持较好,可以得到连续、粗细较均匀的纤维;随着HNTs和g-HNTs含量增加,复合纳米纤维膜的拉伸强度和模量先增大后下降,当HNTs和g-HNTs的含量为5％时,两种复合纳米纤维膜的拉伸强度和模量均达到最大值,但PLLA/g-HNTs组复合纳米纤维膜的拉伸强度始终大于相应的PLLA/HNTs组.体外3T3细胞培养结果显示,PLLA/g-HNTs复合纳米纤维膜具有良好的细胞相容性,且优于相应的PLLA和PLLA/HNTs纳米纤维膜.     

改性纳米羟基磷灰石/PLGA复合材料的制备及生物活性

以低聚乳酸接枝改性的羟基磷灰石纳米粒子(op-HA)和聚丙交酯-乙交酯(PLGA)制备的生物可降解纳米复合材料(op-HA/PLGA)为研究对象, 采用FTIR, TGA, ESEM和EDX分析其接枝反应、接枝率、表面形貌和钙磷沉积情况, 通过在材料膜表面接种兔成骨细胞进行体外培养, 采用荧光染色、NIH Image J图像分析和Real-time PCR综合评价细胞在材料表面的形态、黏附面积比、增殖能力和基因表达水平, 以此评价新型骨修复纳米复合材料op-HA/PLGA的表面性质和生物活性. 研究结果表明, op-HA的表面接枝率为8.3%, 掺入至PLGA后可形成富含钙磷的粗糙表面, 促进成骨细胞的黏附、扩展和增殖, 提高Ⅰ型胶原蛋白(Collagen-Ⅰ)、骨形态蛋白-2(BMP-2)和骨连接蛋白(Osteonectin)的基因表达水平, 提高材料的钙磷沉积能力. op-HA/PLGA具有良好的细胞相容性和成骨活性.     

丙烯酸改性聚醚砜中空纤维渗透汽化膜的研究

采用自由基聚合反应制备了丙烯酸接枝改性的聚醚砜中空纤维渗透汽化膜,该膜用于醇／水分离获得了良好的效果。结果表明,通过改变聚合单体的浓度可以控制膜的接枝率,并调节膜的选择性和通量。改性膜的红外光谱和电镜分析结果表明：膜的接枝反应主要发生在中空纤维膜的内表面,膜的外表面接枝程度很低。力学性能测试表明接枝后膜的拉伸强度减弱。     

聚L-乳酸/二氧化硅纳米复合材料及其表面诱导生成类骨磷灰石的制备

为改善纳米SiO2粒子在聚L-乳酸基体中的分散性, 将乳酸齐聚物接枝到纳米SiO2粒子表面, 通过IR, 29Si MAS NMR和TGA对改性SiO2进行表征. 以聚L-乳酸(PLLA)为基体, 加入乳酸齐聚物接枝改性的二氧化硅(g-SiO2)粒子, 采用溶液浇铸法制备PLLA/g-SiO2纳米复合材料, 测试其在模拟体液(SBF)中的生物活性. 通过XRD, IR, SEM和EDS表征手段, 考察材料表面类骨磷灰石形成能力. 结果表明, 乳酸齐聚物成功地接枝到SiO2表面, 当反应36 h时, g-SiO2接枝率最大(9.22%). 随着g-SiO2含量增加和浸泡时间的延长, 材料表面最初形成的无定形沉积物矿化成碳酸羟基磷灰石(Carbonated hydroxyapatite, CHA), 钙磷比为1.72, 类似于人骨无机质, 表明g-SiO2的引入能明显加速复合材料表面CHA沉积, 该复合材料有望成为骨修复填充材料和组织工程支架材料.     

纳米SiO_2/聚丙烯复合材料的反应性增容

利用反应性增容技术制备了纳米二氧化硅/聚丙烯复合材料.首先探讨了将甲基丙烯酸缩水甘油酯-丙烯酸丁酯共聚物接枝到纳米二氧化硅粒子表面进行改性的各种影响因素,然后将接枝改性纳米二氧化硅与聚丙烯以及作为反应性增容剂的氨基化聚丙烯共混.结果表明,改性粒子上的环氧基与氨基化聚丙烯上的氨基之间的化学反应大大增强了复合材料的界面作用,从而在粒子含量很低时明显提高了聚丙烯的拉伸强度、模量和冲击强度.     

纳米SiO_2锚固光敏基团引发MMA光接枝聚合研究

对纳米SiO2进行了锚固光引发剂的表面修饰,进而引发甲基丙烯酸甲脂(MMA)光接枝聚合制备有机/无机复合粒子.纳米SiO2粒子首先用氯化亚砜进行表面氯化,再与光引发剂2-羟基-4-(2-羟基乙氧基)-2-甲基苯丙酮(Irgacure2959)反应从而锚固上光引发剂.通过紫外光引发MMA在经过修饰过的纳米SiO2表面上进行表面光接枝聚合.采用IR、TGA和TEM等方法表征了接枝前后纳米粒子的变化,证明了表面接枝物的存在,并研究了不同反应条件对单体转化率、接枝率和接枝效率的影响.研究结果表明,搅拌对接枝过程的影响比较显著.TGA结果显示未搅拌聚合时接枝率只能达到比较小的程度,而在搅拌条件下180min内MMA的接枝率可达到110%.     

甲基丙烯酸丁酯在纳米TiO2表面的原位接枝

利用分子自组装技术,对纳米TiO2粒子表面组装上有机单分子层,使其带上不饱和基团C=C,在自组装单分子层表面原位引发甲基丙烯酸丁酯（BMA）单体聚合反应,使纳米TiO2表面形成化学键合的聚合物层,达到对纳米TiO2粒子改性的目的。讨论了不同反应条件对接枝聚合率的影响,通过FTIR、TG-DTA等分析手段,研究聚合改性物质的结构和改性后纳米TiO2粒子的分散稳定性。实验发现聚合改性后的纳米TiO2在有机相中有良好的分散性。     

左旋聚乳酸/聚己内酯/氧化锌复合材料的制备及性能

基于左旋聚乳酸（PLLA）固有低韧性的缺点,分别引入可降解且柔韧性好的聚己内酯（PCL）和刚性纳米粒子氧化锌（nano-ZnO）对其改性,通过溶液共混的方法制备了PLLA/PCL/ZnO复合材料。借助DSC、DMA考察了复合材料的热行为和粘弹性,研究发现,PCL和ZnO的引入对PLLA复合材料的玻璃化转变温度没有影响,说明复合材料是不相容体系;随着PCL、ZnO含量的增多,PLLA的熔融峰向低温偏移。拉伸实验结果表明,PLLA/2%PCL/1%ZnO组分的复合材料拉伸韧性最佳,断裂伸长率达到了35%,比纯PLLA的断裂伸长率提升了20倍。然而,相同比例的PCL和ZnO单独对PLLA改性时,断裂伸长率分别为17%和4%,说明两者协同作用的增韧效果更好。拉伸断面的观察结果表明,PCL/ZnO含量增多时PCL分散相尺寸增大、相分离显著,且ZnO粒子趋于聚集,因而导致增韧效率下降。     

型胶原在聚-L-乳酸(PLLA)表面的化学接枝和涂层及其对软骨细胞生长的促进作用

采用接枝-涂层技术在聚-L-乳酸(PLLA)膜表面接枝聚甲基丙烯酸(PMAA)得到稳定的PLLA-g-PMAA胶原涂层.利用水溶性碳化二亚胺作为缩合剂,使PLLA-g-PMAA表面的羧基和胶原分子中的氨基发生缩合反应,从而将型胶原接枝在PLLA表面;同时保留材料表面物理涂层的胶原溶液,获得了稳定的胶原涂层.XPS谱图证实了接枝反应的发生.分别用比色法和茚三酮法测定了PLLA-g-PMAA表面的羧基密度和PLLA膜表面胶原的接枝量和涂层量.细胞培养结果表明,改性后的PLLA膜表面软骨细胞的铺展性能和增长速度明显改善.     

Surface‐modified hydroxyapatite linked by L‐lactic acid oligomer in the absence of catalyst

A new surface modification method of hydroxyapatite nanoparticles (n‐HA) by surface grafting reaction of L ‐lactic acid oligomer with carboxyl terminal (LAc oligomer) in the absence of any catalyst was developed. The LAc oligomer with a certain molecular weight was directly synthesized by condensation of L ‐lactic acid. Surface‐modified HA nanoparticles (p‐HA) were attested by Fourier transformation infrared spectroscopy, ³¹P MAS‐NMR, and thermal gravimetric analysis (TGA). The results showed that LAc oligomer could be grafted onto the n‐HA surface by forming a Ca carboxylate bond. The grafting amount of LAc oligomer was about 13.3 wt %. The p‐HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p‐HA/PLLA composite containing 15 wt % of p‐HA were 68.7 MPa and 2.1 GPa, respectively, while those of the n‐HA/PLLA composites were 43 MPa and 1.6 GPa, respectively. The p‐HA/PLLA composites had better thermal stability than n‐HA/PLLA composites and neat PLLA had, as determined by isothermal TGA. The hydrolytic degradation behavior of the composites in phosphate buffered saline (PBS, pH 7.4) was investigated. The p‐HA/PLLA composites lost their mechanical properties more slowly than did n‐HA/PLLA composites in PBS because of their reinforced adhesion between the HA filler and PLLA matrix. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5177–5185, 2005     

A quaternary composite fiber membrane for guided tissue regeneration

This work reported a novel composite fiber membrane containing poly(1actic‐co‐glycolic acid)/six‐armed poly(ε‐caprolactone)/hydroxylapatite‐grafted poly(l ‐lactide)/Pluronic F‐108 (PLGA/SAPCL/HA‐g‐PLLA/PF‐108) produced by electrospinning. SAPCL, HA‐g‐PLLA, and PF‐108 could be well blended with PLGA to make fibers. Fibrous surface and diameter had little difference in morphology with the change of fibrous component. Compared with simple PLGA, PLGA/SAPCL, or PLGA/SAPCL/HA‐g‐PLLA fiber membrane, the quaternary composites not only showed the improved mechanics stability but also possessed better hydrophilicity. The quaternary membrane was conductive to accelerate degradation and maintained nice bioactivity. It was not cytotoxicity. These results suggest that the composite fiber membrane may be qualified as guided bone regeneration substrate. Copyright © 2015 John Wiley & Sons, Ltd.     

Preparation of PLLA/PLGA microparticles using solution enhanced dispersion by supercritical fluids (SEDS).

In this work, poly(L-lactic acid)/poly(lactide-co-glycolide) (PLLA/PLGA) microparticles were prepared using the technique of solution-enhanced dispersion by supercritical fluids (SEDS). For comparison, separate PLLA and PLGA microparticles were also produced by the same SEDS process. The produced microparticles were characterized by scanning electron microscopy, laser particle size analyzer, X-ray diffraction, differential scanning calorimetry, Fourier transform infrared spectroscopy, and gas chromatography. Results indicate that PLLA/PLGA microparticles possess sphere-like shapes with smooth surfaces. The mean particle size of PLLA/PLGA microparticles ranges from 1.76 to 2.15 microm, depending on the feeding ratio of PLLA to PLGA used in the SEDS process. The crystallinity of PLLA/PLGA microparticles decreases after the SEDS processing, so that the produced microparticles are in an amorphous state. Pure PLGA was hard to precipitate in small, fine microparticle form without the presence of PLLA. A model drug, paclitaxel, was encapsulated into PLLA/PLGA microparticles by the same SEDS process, and the in vitro release rate of paclitaxel from these PLLA/PLGA composites could be modulated by variation of the mixing ratio PLLA:PLGA. The prepared microparticles have negligible residual organic solvent. Drug-loaded PLLA/PLGA microparticles produced by SEDS have potential as an advanced colloidal suspension for pharmaceutical applications.     

Controlled functionalization of multiwalled carbon nanotubes with various molecular-weight poly(L-lactic acid)

Multiwalled carbon nanotubes (MWNT) were functionalized with poly(L-lactic acid) (PLLA) with different molecular weights using a "grafting to" technique. The oxidized MWNT (MWNT-COOH) were converted to the acyl-chloride-functionalized MWNT (MWNT-COCl) by treating them with thionyl chloride (SOCl2) and reacting them with PLLA to prepare the MWNT-g-PLLA. FTIR and Raman spectroscopy revealed that the PLLA was covalently attached to the MWNT, and the weight gain due to the functionalization was determined by thermogravimetric analyses (TGA). The Raman signals of the MWNT were greatly weakened as a result of the PLLA grafting. The morphology of the grafted PLLA was examined by using SEM and TEM. The amount of grafted PLLA depended on the molecular weight of the PLLA. The PLLA coated on the MWNT became thicker and more uniform with increasing PLLA molecular weight from 1000 to 3000. However, the amount of grafted PLLA became lower when the molecular weight of PLLA was further increased to 11,000 and 15,000, and the PLLA attached to the MWNT showed a squid leglike morphology forming blobs and leaving much of the MWNT surface bare.     

Mechanical and thermal properties of polypeptide modified hydroxyapatite/poly(L-lactide) nanocomposites

A new type of polypeptide(poly(-benzyl-L-glutamate)(PBLG))modified hydroxyapatite(HA)/poly(L-lactide)(PLLA)nanocomposites(PBLG-g-HA/PLLA)were prepared by the solvent-mixing method,and their mechanical and thermal properties were investigated.The tensile test showed that the mechanical properties of PBLG-g-HA/PLLA nanocomposites were better than that of PLLA,even a 0.3 wt%content of PBLG-g-HA in the nanocomposites could make the tensile strength 12%higher than that of the neat PLLA sample,and the tensile mod...     

紫外辐射接枝法修饰聚乳酸表面及其细胞相容性

通过紫外辐射接枝在聚乳酸膜表面引入聚丙烯酸的方法使聚乳酸材料表面的亲水性和细胞相容性得到改善,研究了各种处理条件对材料表面的羧基密度、表面形态和表面接触角的影响,同时还考察了紫外辐射接枝聚丙烯酸的聚乳酸表面的成骨细胞相容性.红外光谱分析和羧基密度测定结果表明:通过紫外光引发接枝,聚丙烯酸被成功接枝到聚乳酸表面,而且接枝密度受接枝时间和聚丙烯酸质量分数的影响很大.接触角和原子力显微镜研究结果表明:接枝聚丙烯酸后的聚乳酸表面的亲水性和粗糙度明显增加,能够促进成骨细胞的生长.     

Composites of poly(L‐lactide‐trimethylene carbonate‐glycolide) and surface modified SBA‐15 as bone repair material

This work aims to develop novel composites from a poly(L ‐lactide‐co‐trimethylene carbonate‐co‐glycolide) (PLTG) terpolymer and mesoporous silica (SBA‐15) nanofillers surface modified by post‐synthetic functionalization. SBA‐15 first reacts with a silane coupling agent, γ‐aminopropyl‐trimethoxysilane to introduce ammonium group. PLLA chains were then grafted on the surface of SBA‐15 through ammonium initiated ring‐opening polymerization of L ‐lactide. Composites were prepared via solution mixing of PLTG terpolymer and surface modified SBA‐15. The structures and properties of pure SBA‐15, γ‐aminopropyl‐trimethoxysilane modified SBA‐15 (H₂N‐SBA‐15), PLLA modified SBA‐15 (PLLA‐NH‐SBA‐15), and PLTG/PLLA‐NH‐SBA‐15 composites were characterized by Fourier transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy, N₂ adsorption‐desorption, differential scanning calorimetry, contact angle measurement, and mechanical testing. The results demonstrated that PLLA chains were successfully grafted onto the surface of SBA‐15 with grafting amounts up to 16 wt.%. The PLTG/PLLA‐NH‐SBA‐15 composites exhibit good mechanical properties. The tensile strength, Young's modulus, and elongation at break of the composite containing 5 wt.% of PLLA‐NH‐SBA‐15 were 39.9 MPa, 1.3 GPa, and 273.6%, respectively, which were all higher than those of neat PLTG or of the composite containing 5 wt.% of pure SBA‐15. Cytocompatibility tests showed that the composites present very low cytotoxicity.     

Protein immobilization on the surface of poly-L-lactic acid films for improvement of cellular interactions

To covalently immobilize gelatin or collagen type I on poly-L-lactic acid (PLLA) film surfaces poly(hydroxyethyl methacrylate) (PHEMA) or poly(methacrylic acid) (PMAA) was grafted via photooxidization and subsequent UV-induced polymerization [Makromol. Chem. 186 (1985) 1533.1]. For films grafted with PHEMA, methyl sulfonyl chloride was used to activate the hydroxyl groups and for films grafted with PMAA 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide was used to activate the carboxyl groups. Gelatin and collagen were finally reacted with the activated hydroxyl or carboxyl groups to obtain covalently immobilized protein layers. Grafting of PHEMA, PMAA and protein on the surfaces was confirmed using ATR-IR and XPS. Surface wettability of the modified films was improved. The protein immobilized PLLA may be widely used as a biocompatible material.