微米及纳米丝光沸石分子筛上二甲醚羰基化反应的积碳分析

对比研究了在传统微米尺寸和新结构纳米丝光沸石催化剂上二甲醚羰基化合成乙酸甲酯的反应行为.结果表明,通过减小分子筛的尺寸到纳米水平,可以有效提高反应物和产物到达或者脱离反应活性位的效率,从而提高了二甲醚的转化率;更重要的是,抑制了硬积碳的生成,使催化剂保持了更高的稳定性.     

环己烯水合制备环己醇的研究Ⅰ. 分子筛结构及晶粒大小的影响

考察了三种不同结构的分子筛(ZSM-5,MCM-22及β)以及不同晶粒大小的ZSM-5分子筛对环己烯水合反应的催化活性. 结果表明,具有12元环孔道体系的β分子筛对环己烯的转化率(9.6%)最高,但对环己醇的选择性(35.4%)最差. MCM-22分子筛的活性很低,其环己烯转化率只有0.8%. 而孔口为10元环结构的ZSM-5分子筛则具有较高的活性(环己烯转化率7.5%)和产物选择性(99.2%),因此是较好的水合催化剂. ZSM-5分子筛的晶粒大小对其环己烯水合反应活性有明显的影响,分子筛晶粒越细,则水合反应活性越高,其原因在于晶粒变细增大了分子筛的外比表面积,从而增加了接近孔口处的活性中心的数量.     

在稀土改性的ZSM-5沸石催化剂上甲苯歧化选择生成对二甲苯的研究

本文研究了ZSM-5沸石催化剂用稀土元素(La~(3 )、Ce~(3 )、Pr~(3 )、Nd~(3 ))以及混合稀土浸渍改性处理后对甲苯歧化反应的催化性能。实验结果表明:上述四种稀土元素改性处理后的催化剂的甲苯转化率均随着载入量的增加而下降,而对二甲苯的选择性都有所提高。在浸渍法制备的La-ZSM-5沸石催化剂上,甲苯歧化生成对二甲苯的选择性可达80%。试验还指出,单独用磷改性的ZSM-5沸石催化剂的活性较低。再用稀土对PZSM-5催化剂改性,可使甲苯转化率从18%提高到30%。这是由于三价稀土元素可提供较多的质子酸中心。也是由于载入的磷和稀土元素对催化剂孔口和孔道尺寸有影响,从而改变了反应组份在分子筛中的扩散性质,提高了催化剂在生成对二甲苯时表现出的择形选择性。在一组用二种元素如磷-稀土、磷-镁和磷-镧改性的ZSM-5沸石催化剂中,评选出了对甲苯歧化反应具有较高活性和选择性的磷-镧改性催化剂,甲苯转化率为17%时,对二甲苯选择性可达90%左右。并且研究了反应条件对活性、选择性和反应产物的分布。在常压临氢条件下用该催化剂连续反应24小时,其活性稳定,转化率基本不变。     

大晶粒ZSM-5分子筛的合成及其催化性能的研究

ZSM-5分子筛对许多正碳离于反应有优异的择形催化性能。近年来的研究表明,ZSM-5沸石的晶粒大小对其催化活性、选择性和稳定性有显著影响。如对甲苯歧化、甲苯与甲醇的甲基化反应,大晶粒ZSM-5分子筛对生成对二甲苯有较高的选择性。对于二甲笨液相异构化反应,小晶粒ZSM-5沸石具有较高的催化活性和选择性。我们用“直接法”合成了大晶粒(34×116μ)ZSM-5沸石分子筛,比较了不同晶粒大小ZSM-5分子筛催化剂在一些反应中的催化性能。大晶粒ZSM-5分子筛系不用有机胺,直接用水玻璃、硫酸铝、硫酸为原料合成的。用光学显微镜、扫描电镜观察所得分子筛的晶粒外形和大小,取5—6个有代表性的晶粒计算其平均尺寸。用BET重量法测定分子筛对正己烷、环己烷和水的吸附量。用X—射线衍射分析样品的物相。在160—200℃温度范围内考察了晶化温度对晶粒大小的影响,所得结果如表1。     

二甲醚催化转化制甲苯的反应研究

在氧气气氛中,对氧化钨改性的不同分子筛催化剂上二甲醚(DME)转化反应进行了评价。结果表明,WO3/HZSM-5催化剂上DME可以高选择性转化为甲苯,对其反应工艺条件进行了优化,常压、290℃、DME/O2比为2∶1时,二甲醚几乎完全转化,转化率为98.97%,甲苯的选择性达到39.71%。对催化剂结构和酸性进行表征,结果表明,ZSM-5分子筛的孔道结构最有利于甲苯的生成,WO3的介入调整了HZSM-5分子筛表面的酸性活性位点分布,在氧气气氛中有效地抑制了副产物的生成,使产物中甲苯的选择性提高。     

焙烧方法和焙烧条件对纳米Au/HZSM-5催化剂金粒径和催化性能的影响

采用负压沉积沉淀法制备了纳米Au/HZSM-5催化剂前体,研究了深床焙烧和等离子体焙烧两种方法,以及焙烧温度和焙烧气氛对催化剂中纳米金粒径和催化性能的影响,并采用ICP、TEM、XRD、UV-vis、XPS等表征方法对催化剂金粒子进行了物化性能表征,采用合成气羰基化制乙酸甲酯反应表征催化性能。结果表明,不同焙烧方法和不同焙烧温度及气氛对负载型纳米Au/HZSM-5催化剂中金粒径、形貌、物化性质和催化性能有明显影响。其中,以等离子体焙烧方法在500℃氮气气氛下制备的纳米1.86%Au/HZSM-5催化剂中的金粒径最小,为2-5 nm。用于催化合成气羰基化制乙酸甲酯反应,原料中CO的转化率为67%,乙酸甲酯选择性可达78%。     

ZSM-5的水热改性及其在合成气经二甲醚制汽油中的应用

对合成气经二甲醚制汽油两段等压反应系统中的ZSM-5分子筛催化剂进行原位水热处理,研究了不同温度下水蒸气处理ZSM-5分子筛的结构、表面酸性及催化反应性能。XRD、XRF、BET、NH₃-TPD 和 TPO等表征手段表明,水热处理温度为400℃时会使ZSM-5分子筛大部分非骨架铝脱除,酸中心数量减少,比表面积增加,提高了催化剂的活性及产物选择性。     

不同晶粒尺寸H-ZSM-5催化剂上甲醇芳构化反应性能

芳烃是一类重要的有机化工基础原料,通常采用传统的石油路线生产芳烃,包括催化裂化和催化重整等工艺.由于石油资源的紧缺,以可再生资源为原料生产芳烃工艺的发展具有十分重要的意义.甲醇作为一种重要的基础原料,可来源于煤、天然气和生物质等,因此,甲醇制芳烃工艺(MTA)的研究受到日益关注.ZSM-5分子筛具有较大的比表面积、可调节的酸性、优良的择形选择性和很高的水热稳定性,因而在甲醇芳构化中展现出良好的催化性能.研究发现,甲醇转化率和产物分布与ZSM-5分子筛的酸性和多孔性等密切相关.本文通过调控模板剂与水的比例和晶化时间,采用水热法制备了一系列不同晶粒度H-ZSM-5分子筛催化剂,通过X射线衍射(XRD)、扫描电镜(SEM)、N2物理吸附脱附(BET)和X射线荧光光谱等技术对所得分子筛的理化性质、骨架结构和形貌进行了表征;采用吡啶红外光谱和NH3程序升温脱附技术对其酸性进行了分析,使用热重(TG)技术对反应后催化剂的积碳含量进行了分析,并将所制备的H-ZSM-5分子筛催化剂分别应用于MTA反应,系统性地探究分子筛晶粒度对其理化性质和MTA催化性能的影响.XRD结果表明,所合成的五种样品均具有典型的ZSM-5分子筛特征衍射峰且无杂晶,且具有不同的晶粒度,分别为4.0±0.3,1.2±0.2 μm,614.1±31.9、391.9±32.4和99.1±7.0 nm.N2物理吸附脱附曲线可以发现,晶粒度为99.1±7.0 nm的ZSM-5分子筛展现出典型的Ⅰ型和Ⅳ型物理吸附曲线且在较高的相对压力(P/Po=0.8-1.0)处有一个明显的H4型迟滞环,表明此分子筛具有介孔和大孔结构;BJH吸附孔径分布图表明,这些介孔主要分布在2-7和20-50 nm范围内;同时各样品的比表面积和孔体积随着其晶粒度的减小而增大.结果还表明五种不同晶粒度的ZSM-5分子筛具有相似的SiO2/Al2O3摩尔比和酸性质.MTA反应结果表明,随着催化剂晶粒度的降低,甲醇的平均转化率,芳烃选择性和BTX选择性有所提高,在300 min时晶粒度较大的三个催化剂上,甲醇转化率迅速降至90％,而晶粒度较小的两个催化剂上,甲醇转化率始终维持在95％以上,其中晶粒度为99.1±7.0 nm的样品上芳烃选择性最高(平均42％以上),BTX选择性达37％.对失活催化剂积碳含量分析,随着催化剂晶粒度的降低,积碳量降低.晶粒度较低的纳米分子筛催化剂具有更短的孔道,更高效的扩散性能,更高的比表面积和独特的梯级孔结构,因而在甲醇芳构化反应中展现出更长的寿命,更高的活性和更低的积碳量,在甲醇制芳烃工业化生产中具有巨大潜力.     

柠檬酸处理对ZSM-5分子筛甲缩醛气相羰基化性能的影响

采用柠檬酸对晶种法制备的低硅铝比ZSM-5纳米晶聚集体进行改性处理,并将其应用于催化甲缩醛(DMM)气相羰基化合成甲氧基乙酸甲脂(MMAc)反应.结果表明,通过调控柠檬酸处理时间可以有效地改进所制备ZSM-5分子筛的催化羰基化性能.其中,使用0.2 mol/L柠檬酸在80℃下处理12 h后的ZSM-5分子筛可获得59.5%DMM转化率和59.3%的MMAc选择性,MMAc收率从16.9%提高到35.3%.通过SEM、 TEM、 ICP、 N_2-BET、 Py-FTIR、 NH_3-TPD等表征手段对分子筛进行详细表征分析,发现适当调控柠檬酸处理时间,可使得纳米晶聚集体ZSM-5分子筛酸强度降低,并暴露出更多的中强B酸位点,同时增大分子筛比表面积及孔道体积.酸性位点的增多促使DMM转化率提高,而酸强度的降低、比表面积及孔道体积的增加,有助于调控中间物种的反应路径及扩散程度,进而抑制部分副反应,提高目标产物MMAc的选择性.     

不同晶粒尺寸H-ZSM-5催化剂上甲醇芳构化反应性能（英文）

芳烃是一类重要的有机化工基础原料,通常采用传统的石油路线生产芳烃,包括催化裂化和催化重整等工艺.由于石油资源的紧缺,以可再生资源为原料生产芳烃工艺的发展具有十分重要的意义.甲醇作为一种重要的基础原料,可来源于煤、天然气和生物质等,因此,甲醇制芳烃工艺(MTA)的研究受到日益关注.ZSM-5分子筛具有较大的比表面积、可调节的酸性、优良的择形选择性和很高的水热稳定性,因而在甲醇芳构化中展现出良好的催化性能.研究发现,甲醇转化率和产物分布与ZSM-5分子筛的酸性和多孔性等密切相关.本文通过调控模板剂与水的比例和晶化时间,采用水热法制备了一系列不同晶粒度H-ZSM-5分子筛催化剂,通过X射线衍射(XRD)、扫描电镜(SEM)、N_2物理吸附脱附(BET)和X射线荧光光谱等技术对所得分子筛的理化性质、骨架结构和形貌进行了表征;采用吡啶红外光谱和NH_3程序升温脱附技术对其酸性进行了分析,使用热重(TG)技术对反应后催化剂的积碳含量进行了分析,并将所制备的H-ZSM-5分子筛催化剂分别应用于MTA反应,系统性地探究分子筛晶粒度对其理化性质和MTA催化性能的影响.XRD结果表明,所合成的五种样品均具有典型的ZSM-5分子筛特征衍射峰且无杂晶,且具有不同的晶粒度,分别为4.0±0.3,1.2±0.2μm,614.1±31.9、391.9±32.4和99.1±7.0 nm.N_2物理吸附脱附曲线可以发现,晶粒度为99.1±7.0 nm的ZSM-5分子筛展现出典型的Ⅰ型和Ⅳ型物理吸附曲线且在较高的相对压力(p/p_0=0.8-1.0)处有一个明显的H4型迟滞环,表明此分子筛具有介孔和大孔结构;BJH吸附孔径分布图表明,这些介孔主要分布在2-7和20-50 nm范围内;同时各样品的比表面积和孔体积随着其晶粒度的减小而增大.结果还表明五种不同晶粒度的ZSM-5分子筛具有相似的SiO_2/Al_2O_3摩尔比和酸性质.MTA反应结果表明,随着催化剂晶粒度的降低,甲醇的平均转化率,芳烃选择性和BTX选择性有所提高,在300 min时晶粒度较大的三个催化剂上,甲醇转化率迅速降至90%,而晶粒度较小的两个催化剂上,甲醇转化率始终维持在95%以上,其中晶粒度为99.1±7.0 nm的样品上芳烃选择性最高(平均42%以上),BTX选择性达37%.对失活催化剂积碳含量分析,随着催化剂晶粒度的降低,积碳量降低.晶粒度较低的纳米分子筛催化剂具有更短的孔道,更高效的扩散性能,更高的比表面积和独特的梯级孔结构,因而在甲醇芳构化反应中展现出更长的寿命,更高的活性和更低的积碳量,在甲醇制芳烃工业化生产中具有巨大潜力.     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.