快速溶剂萃取气相色谱法测定蔬菜中六六六和滴滴涕的残留量

建立了蔬菜中六六六和滴滴涕残留量快速溶剂萃取气相色谱的分析方法。该法的α-六六六、β-六六六、γ-六六六、δ-六六六、PP’-滴滴伊、OP’-滴滴涕、PP’-滴滴滴、PP’-滴滴涕检出限均≤0.05μg/L。加标回收率为88.6%—101.1%,相对标准偏差(RSD)小于8%。该法步骤简单快速,适用于蔬菜中六六六和滴滴涕农药的快速检测。     

纳米TiO2光催化转化下有机氯农药与AgNO3的光谱特性研究

以TiCl4为原料,利用水解法制备了锐钛矿型纳米TiO2。研究了α,β,γ,δ-六六六(BHC)、滴滴涕、狄氏剂、三氯杀螨醇、七氯等含氯农药在纳米TiO2的悬浮体系和紫外光的作用下的降解行为。由于C—Cl键能的关系,不同有机氯农药的光降解效率有很大的不同,其降解率为三氯杀螨醇>狄氏剂>滴滴涕>七氯的降解率,而对六六六的异构体,其降解率顺序为-αBHC>-γBHC>-δBHC>-βBHC。研究了Cl-在聚乙烯醇表面活性剂溶液中生成氯化银溶胶在260 nm左右的吸光光谱特性,通过有机氯转化为无机氯离子(Cl-)以及Cl-浓度与氯化银溶胶吸光值之间的线性关系的方式,实现有机氯农药含量的间接测定。     

ICP-AES法测定蚂蚁粉中多种微量元素

研究了ICP－AES法测定蚂蚁粉中多种微量元素的方法，通过方法试验确认采用低温灰化法制备样品，不仅能满足ICP－AES法测定的要求，同时具有样品处理方法简单，快速，经济等优点，其方法的回收率在92．0－100．7％之间，精密度在0．20％－9．29％之间，实验数据证明该方法完全可以满足同类样品的微量元素检测要求。     

钯—抗坏血酸基体改进剂平台石墨炉原子吸收光谱法测定贻贝标样中的砷

本实验建立了钯－抗坏血酸基体改进剂平台石墨炉原子吸收光谱法测定贻贝中砷的方法。研究了基体改进剂氯化钯、抗坏血酸用量对测定的影响，比较了氯化钯－抗坏血酸、氯化钯、硝酸镍三种基体改进剂及平台石墨管、普通石墨管在测定贻贝中砷的灵敏度。方法的相对标准偏差为３．２％，回收率在９７．８％－１０７．４％之间，检出限为１２．０ｎｇ／ｍＬ。     

微波消化-连续流动进样冷原子吸收法测定中成药中痕量汞

本实验室建立了用微波消化系统，消化中成药样品，用连续流动进样冷原子吸收法测定了中成药中痕量汞的方法。研究了硝酸－过氧化氢和硝酸－硫酸－高氯酸两种不同混合酸的消化体系及消化时间和压力对测定结果的影响。方法的相对标准偏差为４．９％，回收率在９１％—１１６％之间，检出限为０．１５ｎｇ／ｍＬ。     

钯－抗坏血酸基体改进剂平台石墨炉原子吸收光谱法测定贻贝标样中的砷

本实验建立了钯－抗坏血酸基体改进剂平台石墨炉原子吸收光谱法测定贻贝中砷的方法。研究了基体改进剂氯化钯、抗坏血酸用量对测定的影响，比较了氯化钯－抗坏血酸、氯化钯、硝酸镍三种基体改进剂及平台石墨管、普通石墨管在测定贻贝中砷的灵敏度。方法的相对标准偏差为３．２％，回收率在９７．８％—１０７．４％之间，检出限为１２．０ｎｇ／ｍＬ。     

金属铝中杂质元素的测定及其基体影响的研讨

提出了一种能同时测定金属铝中杂质元素Ｃｕ＇Ｍｎ，Ｍｇ，Ｚｎ，Ｃｒ，Ｎｉ，Ｖ，Ｔｉ，Ｆｅ，Ｓ的ＩＣＰ－ＡＥＳ分析方法，实验考察了金属铝基体，共存元素、不同溶剂等因素驿分析元素测试结果的影响，选择了仪器最佳工作条件。结果表明，当金属铝基体的纯度为９６．００％－９９．９０％时，分析元素的回收率在９５－１０５．０５之间。相对标准偏差ＲＳＤ均小于０．５％。在金属铝进出口商品检验中已获得满意的结果。     

微波萃取-气相色谱法测定土壤中六六六、滴滴涕

用微波萃取和GC-ECD联用技术.对土壤中六六六、滴滴涕进行了分析.实验具有操作简便,分析时间短,应用范围广等优点.并且进行了回收率、重现性及精密度的测定.     

环丙沙星在胶束体系中的荧光特性研究及应用

研究了环丙沙星在胶束体系中的荧光性质，发现十二烷基硫基酸对环丙沙星有较强的增敏作用。据此建立了胶束增敏荧光光谱法测定痕量环丙沙星的新方法，经样品测定，其线性范围为0．033－0．60μg.mL^-1，检出限为0．033μg.mL^-1，回收率为94．0％－98．1％相对标准偏差为1．5％－2．8％。     

ICP-AES法测定水中微量磷

用ICP－AES法测定水中磷，并确定了最佳测定条件，检出限为0．02μg.mL^-1，回收率为96．5％－102．1％，RSD为1．65％－2．83％。该法准确、快速、简便，应用于水中磷的测定，结果令人满意。     

Speckle characteristics of a broad-area VCSEL in the incoherent emission regime

We present a technique to reduce the speckle contrast of a NIR broad-area VCSEL based on the spatially incoherent emission regime that can be obtained when using the proper driving conditions. We evaluate the efficiency of this technique to reduce the speckle contrast by comparing it with the speckle characteristics in multimode emission under cw operation. Depending on the illumination setup, the incoherent emission regime can lead to a strongly reduced speckle contrast down to 1.3%. This is in agreement with estimates of the expected speckle contrast reduction when three contrast reducing effects are taken into account. These low contrast values make the investigated sources attractive for several applications that suffer from speckle noise.     

Structural characterization of ultrathin Cr and Sc films for soft X-ray mirrors

The structure of multilayers of ultrathin scandium (Sc) and chromium (Cr) films has been characterized by means of transmission electron microscopy (TEM). Face centered cubic Sc was found both in magnetron sputtered thin Sc layers on Si(0 0 1) and in Cr/Sc multilayers for soft X-ray mirrors. The single Sc and Cr layers are polycrystalline with randomly oriented grains, while Sc and Cr within the Cr/Sc multilayer show a strong [0 0 1] texture in the deposition direction. From high-resolution images the orientation-relationship at the Cr/Sc interfaces could be deduced as: Sc_[110]//Cr_[100] and Sc_[010]//Cr_[110], which was confirmed by image simulations.     

Optical transmission through an interface between subwavelength slits

This paper studies optical transmission through an interface between two slits with different widths in a sheet composed of an ideal conductor. Such a structure is of potential use in fabricating optical diode and may be the simplest one compared to other designs. Our calculations show that there is a critical wavelength. When the light wavelength is below the critical wavelength, the transmissivity is unidirectional. The expression of the stable transmissivity as a function of the ratio of the widths of the two slits was obtained analytically. Particularly, at the critical wavelength, the transmissivities are zero. This phenomenon has great potential for application in the manufacture of wavelength blockers.     

Effect of Ir(pq)2acac doping on CBP in phosphorescence organic light-emitting diodes

Doping is one of the most powerful methods amongst the various performance improvement ways. Doping affects the energy levels of the host layer by the energy level of the dopant. This allows the energy bandgap to be adjusted to a desired level and thus generates light corresponding to that energy level. Alternatively, it can act as an energy barrier between the interfaces to change the flow of carriers. In this study, the voltage dependences of undoped and doped devices were observed. Bis(2-phenylquinoline) iridium(III) (acetylacetonate) (Ir(pq)₂acac) was doped in 4,4′-N, N′-dicarbazole-biphenyl (CBP) as the emission layer. The light intensity changes with the doping concentration, and the efficiency was also studied. When a high voltage was applied, the effect of triplet-triplet annihilation (TTA) adversely affected the electron-hole recombination. We analyzed the optimal operating conditions and the effect of doping concentration on OLEDs.     

Belle实验观测到新类粲偶素结构

利用在Υ(nS)(n=1,2,4,5)共振态及其附近采集的大量数据,Belle实验测量了末态中含两个矢量粒子的双光子过程γγ→J/ψ和ωJ/ψ.在这两个过程中,发现了两个窄共振结构X(4350)和X(3915).这两个新结构的性质目前尚不清楚,可能是普通粲偶素粒子,也可能是含一对粲夸克和一对轻夸克的四夸克态,或含一对粲夸克和一个激发胶子的混杂态,或是由其他未知的动力学原因造成的奇特结构.Belle同时发现在γγ→J/ψ过程中,不存在显著的Y(4140)的信号,实验结果与将Y(4140)解释为四夸克态的部分理论预期有较大差异.     

Grain boundary potential and charge density at grain boundaries of chemically prepared thin silver sulfide films

The grain boundary potential and interface state charge density at the grain boundaries of silver sulfide (Ag₂S) thin films prepared by chemical conversion of cadmium sulfide (CdS) films have been determined from the dc resistance of the material and are found to be sensitive to annealing. A reduction in the grain boundary potential and the grain boundary charge density of the film has been noticed when the source CdS film is annealed at different temperatures prior to chemical conversion. The variation in the grain boundary charge density of the grown Ag₂S film with source annealing temperature has been found to be similar to that of thin cadmium sulfide film, reported earlier. An additional low temperature heat treatment of the sample results in an enhancement in the charge density at the grain boundaries. The change in the silver vacancy and/or oxygen and sulfur content of the films as revealed from the energy dispersive spectra of the films suggests possible role of film composition on the grain boundary charge density.     

XYZ particles at Belle

In this paper, I review recent progress in the study of the XYZ particles at Belle. I only focus on studies with charmonium and one or more light mesons in the final states. This covers the X(3872), X(3915),Y(4140), X(4350), and the charged Z states.     

三螺旋DNA分子Poly(dT)·Poly(dA)·Poly(dT)碱基振动模式

利用晶格动力学方法计算了三螺旋 DNA分子 poly(d T)· poly(d A)· poly(d T)碱基振动模式 ,并根据势能分布矩阵对碱基振动模式进行了指定。计算的模式频率同拉曼光谱实验相符合     

Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

The effect of phonon anisotropic scattering on the thermal conductivity of silicon thin films at 300K and 400K

Previous studies have shown that anisotropy in phonon transport exist because of the difference in phonon dispersion relation due to different lattice directions, as observed by a difference in in-plane and cross-plane thermal conductivities. Our current work intends to study the effect of anisotropy scattering on silicon thermal conductivity at 300 K and 400 K. We adopt the Henyey and Greenstein probability density function in our phonon Monte Carlo simulation to investigate the effect of highly forward and backward scattering events. The impact of applying the anisotropy scattering using this approach is discussed in detail. While the forward and backward scattering will increase and decrease thermal conductivity respectively, the extent of the effect is non-linear such that forward scattering has a more obvious effect on thermal conductivity than backward scattering.