一种多模干涉耦合器的性能模拟

为减小多模干涉（Multimode Interference ,MMI）耦合器件的尺寸,提出一种多模波导宽度为指数型变化的Taper结构.理论分析了多模波导长度与该Taper结构的参量之间的关系.与已被用于减小MMI器件尺寸的抛物线型Taper结构相比,该结构可进一步减小器件的尺寸.就几种波导结构参量下的MMI耦合器,利用宽角光束传播法进行了数值模拟.结果表明,指数型MMI耦合器的性能与抛物线型MMI耦合器的性能类似.指数型Taper结构可以用于MMI器件以减小该类器件的尺寸.     

锥形多模干涉耦合器一般成像特性分析

锥形多模干涉耦合器克服了传统多模干涉(MMI)耦合器结构尺寸大的缺点,满足当前集成光器件高集成度的要求.其成像特性对设计基于它的集成光器件至关重要.根据多模干涉耦合器的自映像原理,对锥形多模干涉耦合器成像特性进行分析,发现成像特性与输入场位置、位置数、多模波导初始宽度及渐变率等参量密切相关,得到成像位置的解析表达式并总...     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

单模与多模光纤耦合器的光束合波

现有的光纤耦合器在作为分波器使用时具有较低的插入损耗,在作为合波器时插入损耗较大,为实现低损耗合波目的,提出一种由单模与多模光纤共同构成的混合型光纤耦合器。利用耦合波方程理论分析其工作原理,计算机模拟其耦合过程。采用熔锥法制作工艺,完成单模与多模光纤耦合器的制作,实验结果与理论模拟相吻合;该器件单模到多模光纤的耦合效率、多模到多模光纤的耦合效率均在90％以上,实现了两路光束的功率合波。作为低插入损耗合波器件可广泛应用于光通信以及双包层光纤激光器抽运光的注入。     

采用三维波束传输法的多模干涉耦合器成像位置的数值计算

多模干涉(MMI)耦合器需要精确定位成像位置,以便器件的设计制作。针对强限制和弱限制的三维多模波导干涉耦合器,采用三维交替方向隐式有限差分光束传输法(BPM),数值计算得出多模波导长度、输入波导和输出波导位置。首先通过对对称干涉多模干涉耦合器的数值分析求得多模干涉耦合器的等效宽度Weq及最低二阶模之间的拍长Lc,然后将这些参量结合光束传输法直接用于器件设计。计算显示该方法得到的成像位置和导模传输分析法(MPA)的理论预测比较接近,但Weq和Lc却是由光束传输法计算得到的,导模传输分析法理论只能在得到Weq和Lc的前提下才能得到成像位置。该方法直接针对三维波导进行,没有采用基于等效折射率方法的从三维波导到二维波导的简化处理,并且也没有采用导模传输分析法所采用的近似,保证了计算精度,对于实际多模干涉器件的设计制作可起参考作用。     

一种改进的2×2 SOI Mach-Zehnder热光开关

本文设计并制作了基于强限制多模干涉耦合器的2×2 SOI马赫-曾德热光开关.这种光开关采用了深刻蚀结构的多模干涉耦合器和输入/输出波导,较大地提高了干涉耦合器的性能并减少了连接耦合损耗.同时,在调制臂区域采用浅刻蚀结构,保持其单模调制状态.深刻蚀多模干涉耦合器具有优越的特性,在实验中测得不均衡度只有0.03 dB,插入损耗－0.6 dB.基于这种耦合器的新型热光开关,其插入损耗为－6.8 dB,其中包括光纤-波导耦合损耗－4.3 dB,开关时间为6.8 μs.     

一种新型SOI Mach-Zehnder干涉型电光调制器的设计

在超紧缩双曲锥形3dB多模干涉耦合器的基础上,设计了一种新的Silicon-on-insulator (SOI) Mach-Zehnder干涉型电光调制器.与传统的Y分支器相比,双曲锥形3dB耦合器的制作容差大,而长度缩短了近30%,使得整个器件的尺寸大幅减小.调制区采用横向注入的PIN结构,模拟结果表明:当外加偏压为0.86V时,器件的调制深度最大,此时注入电流为13.2mA,对应的器件功耗为11.4mW.     

多模干涉型GaAs光功分器的研制

采用导模传输分析法设计了多模干涉型１×４ 光功分器。根据所确定的器件结构参数, 结合器件设计和制作过程中可能遇到的因素, 详细分析了器件中自映像效应多模波导的宽度和长度、波导的折射率等结构参数对器件性能的影响。进行了多模干涉型 Ｇａ Ａｓ １×４ 光功分器的制作和测试。测试结果表明, 所研制的器件实现了１×４ 光功分器功能。针对实验过程和测试结果中遇到的问题进行了讨论, 并提出了进一步完善器件性能的方法。     

一种基于多模干涉耦合器的模转换与合并器件的设计

多模波导干涉（MMI）耦合器在集成光路中被用来实现波导模式的转换或合并。对于实际的基于硅绝缘体（SOI）的三维波导，数值设计方法是必需的。采用有限差分波束传输法（FD-BPM）设计了一种66％模式转换、合并器。首先由FD-BPM求出MMI耦合器的输入、输出波导所支持的基模和一阶导模的模场分布，通过数值方法得到MMI耦合器的长度，然后将求得的模场作为输入波场，经过FD-BPM运算后在器件输出面上计算交叉积分得出实际的由基模转换为一阶模的功率百分比。对于算例中采用的SOI波导，器件长度为829μm，65．7％的功率由基模转换为一阶模。     

Compact 3-dB tapered multimode interference coupler in silicon-on-insulator

We have fabricated a compact 3-dB multimode interference coupler with a large silicon-on-insulator cross section. To reduce the length of the usual symmetric interference multimode interference coupler, we propose using a parabolically tapered structure. The length of the device is 398microm . The device has a uniformity of 0.28 dB.     

Double-clad photonic crystal fiber coupler for compact nonlinear optical microscopy imaging

A 1 x 2 double-clad photonic crystal fiber coupler is fabricated by the fused tapered method, showing a low excess loss of 1.1 dB and a splitting ratio of 97/3 over the entire visible and near-infrared wavelength range. In addition to the property of splitting the laser power, the double-clad feature of the coupler facilitates the separation of a near-infrared single-mode beam from a visible multimode beam, which is ideal for nonlinear optical microscopy imaging. In conjunction with a gradient-index lens, this coupler is used to construct a miniaturized microscope based on two-photon fluorescence and second-harmonic generation. Three-dimensional nonlinear optical images demonstrate potential applications of the coupler to compact all-fiber and nonlinear optical microscopy and endoscopy.     

Simple design of optical fiber displacement sensor using a multimode fiber coupler

A simple design sensor is demonstrated using a fabricated multimode plastic fiber coupler in conjunction with reflective intensity modulation technique. The performances of this sensor are investigated for different light sources. This sensor uses only one fiber for sending and receiving the light and therefore only the back slope exists. The sensor shows the highest performance with the use of yellow light source, which has the highest intensity and the smallest beam divergence. The sensitivity, linear range, resolution and dynamic range of the sensor are obtained at 0.0001 mV/μm, 1500 μm, 70 μm, and 5.0 mm, respectively. The simplicity of the design, high degree of sensitivity, dynamic range and the low cost of the fabrication make it suitable for real field applications.     

Crosstalk comparison of lattice-form optical interleaver with different coupler structures

Lattice circuit made from a cascade of couplers and delay-lines is a popular approach for optical interleaver based on planar lightwave circuit (PLC) technology. Different coupler structures can be employed in the lattice circuit, including 1-stage directional couplers (DCs), 4-stage DCs, and 2-stage multimode interference (MMI) couplers. We fabricated optical interleavers with above three coupler structures, respectively. The experimental results prove that the latter two coupler structures can help to reduce crosstalk, which meets the simulation results well.     

Planar optical coupling elements for multimode fibers with two-step ion migration process

An electric field assisted two-step ion migration process in soda-lime glass plates has been used to produce optical couple waveguides with semicircular and circular cross sections. The radius and the numerical aperture of the guides are approximately the same as those of the graded index multimode fibers. A new coupler structure, the edge reflecting element, which could be used as an integrated demultiplexer in wavelength division multiplexing, has been fabricated. The loss spectrum of the waveguides is analyzed and a theoretical treatment of the ion concentrations is given.     

Simulations of refractive index variation in a multimode interference coupler: Application to gas sensing

An optical sensor based on multimode interference couplers structures has been studied. We have introduced the optical parameters of materials used in existing optical integrated circuits and a sensitive material characterised in previous studies. The variation of optical properties such as the refractive index of the covering sensitive material leads to a modification of waveguiding conditions in the multimode interference coupler. A gas sensor can be developed by measuring the variation of light intensity at the output of the multimode interference coupler structure under gas exposure. Simulations have been performed in order to optimise the output light intensity variations to increase sensitivity. We have shown that these structures are more sensitive than Mach-Zehnder interferometers, and that the relation between dimensions and sensitivity of the multimode interference coupler is not trivial.     

The 650-nm variable optical attenuator based on polymer/silica hybrid waveguide

Visible light variable optical attenuators(VOA) are essential devices in the application of channel power regulation and equalization in wavelength-division multiplexing cross-connect nodes in plastic optical fiber(POF) transmission systems.In this paper, a polymer/silica hybrid waveguide thermo–optic attenuator based on multimode interference(MMI) coupler is designed and fabricated to operate at 650 nm. The single-mode transmission condition, MMI coupler, and transition taper dimensions are optimized through the beam propagation method. Thermal analysis based on material properties provides the optimized heater placement angle. The fabricated VOA presents an attenuation of 26.5 dB with a 21-mW electrical input power at 650 nm. The rise time and fall time are 51.99 and 192 μs, respectively. The time–stability measurement results prove its working reliability.