CNx纳米管的制备、结构观察及低场致电子发射性能研究

采用高温热解法 ,以乙二胺为前驱液 ,在沉积有铁催化剂的p型硅 (1 1 1 )基底上制备出了定向生长的CNx 纳米管 .利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx 纳米管进行了形貌观察和表征 .CNx 纳米管的高度在 2 0 μm左右 ,直径在 5 0— 1 0 0nm之间 ,具有明显的“竹节状”结构 ,结晶有序度较差 .对CNx 纳米管薄膜进行低场致发射性能测试 :外加电场为 1 4V μm ,观察到 2 0 μA cm2 发射电流 ,外电场升至 2 5 4V μm时发射电流达到1 2 80mA cm2 ,在较高外电场下 ,没有发现电流“饱和” .这比相同实验条件下改变前驱液制备出的碳纳米管和硼碳氮纳米管的场发射性能优越 .还在“竹节状”结构的基础上对CNx 纳米管的场致电子发射机理进行了讨论     

不同氮源制备CNx纳米管薄膜及其低场致电子发射性能

采用高温热解法,分别以氯化铵(NH4Cl)和乙二胺(C2H8N2)为氮源在洁净的硅片上沉积生长CNx纳米管薄膜.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CNx纳米管进行形貌观察和表征.结果显示不同氮源制备出的CNx纳米管薄膜的洁净度、有序度以及纳米管的结构明显不同.热解乙二胺(C2H8N2)/二茂铁(C10H10Fe)制备出的结晶度较低的"竹节状"结构CNx纳米管平行基底表面有序生长,而且低场致电子发射性能优越,开启电场1.0V/μm,外加电场达到2.89V/μm时发射电流密度为860μA/cm2.     

不同氮源制备CNx纳米管薄膜及其低场致电子发射性能

采用高温热解法，分别以氯化铵(NH₄Cl)和乙二胺(C₂H₈N₂)为氮源在洁净的硅片上沉积生长CN_x纳米管薄膜.利用扫描电子显微镜、高分辨率透射电子显微镜和拉曼光谱对CN_x纳米管进行形貌观察和表征.结果显示不同氮源制备出的CN_x纳米管薄膜的洁净度、有序度以及纳米管的结构明显不同.热解乙二胺(C₂H₈N₂)/二茂铁(C₁₀H₁₀Fe)制备出的结晶度较低的“竹节状” 结构CN_x纳米管平行基底表面有序生长，而且低场致电子发射性能优越,开启电场1.0V/μm，外加电场达到2.89V/μm时发射电流密度为860μA/cm². 关键词： x纳米管')" href="#">CN_x纳米管 高温热解 “竹节状”结构 场致发射     

类富勒烯纳米晶CNx薄膜及其场致电子发射特性

利用微波等离子体增强化学气相沉积技术制备出了CNx薄膜,并利用x射线光电子能谱、x射线衍射、扫描电子显微镜和Raman光谱等测试手段对所制备的CNx薄膜的微结构和成分进行了分析.研究了其场致电子发射特性.发现薄膜的结构和场发射特性与反应系中的甲烷、氮气及氢气的流量比有关,当甲烷、氢气及氮气流量比为8/50/50sccm时,制备的薄膜具有弯曲层状的纳米石墨晶体结构(类富勒烯结构)和很好的场发射特性.场发射阈值电场降低至1.1V/μm.当电场为5.9V/μm时,平均电流密度达70μA/cm2,发射点密度大于1×104cm-2.     

三极场发射显示器中二次印刷型碳纳米管阴极的制备及特性(英文)

结合丝网印刷技术,研发了一种碳纳米管阴极制备法.利用双壁纳米管作为原材料,并加入细小银颗粒,制作了混合纳米管浆料.将混合纳米管浆料制作在传导电极表面,再将普通纳米管浆料印刷在混合纳米管浆料的上面.在链式烧结炉中对烘烤后的纳米管浆料同时进行烧结以除掉有机溶剂.在进行适当的后处理工艺之后,就形成了二次印刷型纳米管阴极,它能显著改善阴极的场致发射特性.制作了二次印刷型纳米管阴极的三极结构场致发射显示器.该显示器具有更高的发光亮度以及更好的发光图像亮度均匀性.与普通纳米管阴极场致发射显示器相比较,它能够将开启电场从2.15V/μm降低到1.75V/μm,并能够将最大场发射电流从735.8μA提高到1 588.5μA.所研发的纳米管阴极制备方法具有很强的实际应用性,且制作成本低廉.     

二茂铁在高温热解乙二胺制备CN_x纳米管过程中的催化性能研究

采用高温热解法 ,以二茂铁 乙二胺有机溶剂为前驱液制备CNx 纳米管过程中 ,改变前驱液配比 ,对 86 0℃ ,不同二茂铁含量条件下制备出的CNx 纳米管进行了产量统计、形貌结构观察和拉曼光谱研究。结果显示 :随着前躯液中二茂铁含量的相对增大 ,不但CNx 纳米管产量随之增加 ,而且产物中“竹节状”结构纳米管相对“中空”结构纳米管的比重也增大 ;拉曼光谱结果进一步证实了由于“竹节状”结构CNx 纳米管的含量或比重增加所带来的纳米管样品整体或平均含氮量的升高而导致的样品结晶有序程度的降低。对单独钴粉和二茂铁催化条件下生成CNx 纳米管的形貌观察进一步证实 :二茂铁在热解法制备“竹节状”结构CNx 纳米管过程中的浮动催化作用显著 ,有利于实现含氮量较高、结构均匀的CNx 纳米管的可控制生长。     

不同催化剂对热解法制备CNx纳米管的影响

利用铁、钴、镍以及二茂铁为催化剂在高温下热解乙二胺制备CNx纳米管,研究了不同催化剂对CNx纳米管的形貌、结构及产量的影响,并对其催化机理进行了初步讨论.二茂铁和铁催化都能制备出“竹节状”结构的CNx纳米管,但产量较低.钴催化生成CNx纳米管多弯曲,管壁多褶皱,产量较高.镍催化只生成了直径500nm左右的螺旋管.拉曼光谱研究进一步表明,二茂铁催化生成“竹节状”结构CNx纳米管由于氮的掺杂程度相对较高而结晶有序度较低.     

二茂铁催化制备CNx纳米管的研究

采用浮动催化法,选用二茂铁做催化剂,在800 ~1040℃热解乙二胺/二茂铁前驱液制备CNx纳米管对不同温度下制备出的CNx纳米管进行了透射电镜观察、拉曼光谱研究以及产量统计,结果表明,二茂铁催化制备出的CNx纳米管具备较均匀的“竹节状”结构,并随制备温度的升高, CNx纳米管的平均直径增大,结晶有度提高,产量也增加.X射线光电子谱测试分析进一步验证了纳米管中氮原子的掺杂.还对CNx纳米管生长过中二茂铁的催化机理进行了探讨.     

类球状微米金刚石聚晶的场发射

在覆盖金属钛层的陶瓷上,采用微波等离子体化学气相沉积(MPCVD)法制备出类球状微米金刚石聚晶薄膜。利用扫描电子显微镜、拉曼光谱,X射线衍射,分析了薄膜的结构和表面形貌。测试了类球状微米金刚石聚晶膜的场致电子发射特性。开启电场仅为0.55V/μm,在2.18V/μm的电场下,其场发射电流密度高达11mA/cm2。仔细分析了膜的发射过程,发现类球状微米金刚石聚晶的结构对发射有很大影响,并对其发射机理进行了研究。     

白碳纳米晶薄膜及其场致电子发射特性

利用微波等离子体化学气相沉积方法,以甲烷、氢混合气体为反应气体,具有钛镀层的玻璃作为衬底,制备了具有sp¹杂化结构的白碳纳米晶薄膜。利用X射线衍射、俄歇电子能谱,以及扫描电子显微镜对薄膜结构进行了表征。以白碳纳米晶薄膜为阴极,以镀有ITO透明导电薄膜玻璃为阳极,采用二极管结构,测试了白碳纳米晶薄膜的场致电子发射特性。开启电场为2.5 V/μm,在电场为5 V/μm时的电流密度为200μA/cm²。对白碳纳米晶薄膜生长机理,以及其场致电子发射机制进行了讨论。     

两步化学沉积法制备ZnO薄膜及其场发射特性

在低温常压条件下,以ITO玻璃为衬底,采用电化学法与湿化学法结合的两步化学沉积法制备了团簇状ZnO薄膜。利用XRD,SEM分析了薄膜结构和表面形貌,并采用二极管结构在高真空条件下对薄膜进行了场发射性能测试。稳定发射后,开启电场为3.0 V/μm。当电场为5.8 V/μm时,电流密度为583.3 μA/cm²。研究表明:两步化学沉积法低温制备ZnO薄膜是可行的,且该薄膜具有良好的场发射性能。     

High-field electron emission of carbon nanotubes grown on carbon fibers

Carbon nanotubes with uniform density were synthesized on carbon fiber substrate by the floating catalyst method. The morphology and microstructure were characterized by scanning electron microscopy and Raman spectroscopy. The results of field emission showed that the emission current density of carbon nanotubes/carbon fibers was 10 μA/cm² and 1 mA/cm² at the field of 1.25 and 2.25 V/μm, respectively, and the emission current density could be 10 and 81.2 mA/cm² with the field of 4.5 and 7 V/μm, respectively. Using uniform and sparse density distribution of carbon nanotubes on carbon fiber substrate, the tip predominance of carbon nanotubes can be exerted, and simultaneously the effect of screening between adjacent carbon nanotubes on field emission performance can also be effectively decreased. Therefore, the carbon nanotubes/carbon fibers composite should be a good candidate for a cold cathode material.     

Patterned uniformly orientated silicon nanocrystallite films and efficient field emission characteristics

Patterned uniformly (100)-orientated silicon nanocrystallite (SiNC) films were fabricated based on hydrogen ion implantation technique and typical electrochemical anodic etching method. The surface morphology and microstructure characteristics of the films were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, and atomic force microscopy. The efficient field emission with low turn-on field of about 3.2 V/μm at current density of 0.1 μA/cm² was obtained. The emission current density from the SiNC films reached 1 mA/cm² under a bias field of about 11 V/μm. The experimental results demonstrate that the SiNC films have great potential applications for flat panel displays.     

Growth of Y-junction bamboo-shaped CNx nanotubes on GaAs substrate using single feedstock

Nitrogen-doped Y-junction bamboo-shaped carbon nanotubes were synthesized by chemical vapor deposition of monoethanolamine/ferrocene mixture on GaAs substrate at 950 °C. The use of monoethanolamine as the C/N feedstock simplifies the experimental arrangement by producing ammonia during the growth process. The structure, morphology and graphitization of as-grown nitrogen-doped carbon nanotubes (CN_x) were examined by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy analysis. TEM analysis indicates that nanotubes have a bamboo-like structure. The nitrogen concentration on as-grown CN_x nanotube was found to be 7.8 at.% by X-ray photoelectron spectroscopy (XPS) analysis. XPS analysis also indicated that there are two different types of nitrogen atoms (pyridinic and graphitic) in these materials. The possible growth mechanism of formation of Y-junction CN_x nanotubes was briefly discussed. Field emission measurement suggested that as-grown CN_x nanotubes are excellent emitters with turn-on and threshold fields of 1.6 and 2.63 V/μm, respectively. The result indicated that monoethanolamine proves to be an advantageous precursor to synthesize Y-junction nitrogen-doped carbon nanotubes and such nanotubes might be an effective material to fabricate various field emission devices.     

Synthesis and field-emission of aligned SnO2 nanotubes arrays

Aligned tin dioxide (SnO₂) nanotubes have been synthesized by high-frequency inductive heating. Nanotubes with high yield were grown on silicon substrates in less than 5 min, using SnO₂ and graphite as the source powder. Scanning electron microscopy and transmission electron microscopy showed nanotube with diameters from 50 to 100 nm and lengths up to tens of mircrometers. The SnO₂ nanotubes synthesized under the optimum condition have better field-emission characteristics. The turn-on field needed to produce a current density of 10 μA/cm² is found to be 1.64 V/μm. The samples show good field-emission properties with a fairly stable emission current. This type of SnO₂ nanotubes can be applied as field emitters in displays as well as vacuum electric devices.     

碳、碳氮和硼碳氮纳米管场发射性能的比较研究

采用高温热解法在860℃分别制备出了碳、碳氮和硼碳氮纳米管，提纯后利用丝网印刷工艺分别将它们制备成薄膜，并测试了它们的场发射性能.结果表明：碳纳米管、碳氮纳米管和硼碳氮纳米管薄膜的开启电场分别为2.22，1.1和4.4V/μm，当电场增加到5.7V/μm时，它们的电流密度分别达到1400，3000μA/cm²和小于50μA/cm².碳和碳氮纳米管薄膜的场增强因子分别为10062和11521.可见，碳氮纳米管的场发射性能优于碳纳米管，而硼碳氮纳米管的场发射性能比前两者要差.解释了这三种纳米管场发射性能差别的原因. 关键词： 碳纳米管 碳氮纳米管 硼碳氮纳米管 场发射     

Synthesis, characterization and low field emission of CNx nanotubes

Aligned CN_x nanotubes were fabricated by pyrolyzing ethylenediamine on p-type Si(1 1 1) substrates using iron as the catalyst. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectrum (XPS) and Raman spectroscopy were used to characterize the CN_x nanotubes. The CN_x nanotubes with the average length of 20 μm and diameters in the range of 50–100 nm have the “bamboo-like” structure and worse crystalline order. The low-field emission measurements of the CN_x nanotubes indicated that 20 μA/cm² current densities were observed at an electric field of 1.4 V/μm and 1.280 mA/cm² were obtained at 2.54 V/μm. The CN_x nanotubes exhibit better field emission properties than the carbon nanotubes and the BCN nanotubes. The emission mechanism of CN_x nanotubes is also discussed.     

Improving the field-emission properties of carbon nanotubes by magnetically controlled nickel-electroplating treatment

A novel magnetically controlled Ni-plating method has been developed to improve the field-emission properties of carbon nanotubes (CNTs). The effect of the magnetic field and Ni-electroplating on CNT field-emission properties was investigated, and the results are demonstrated using scanning electron microscopy, J-E and the duration test. After treatment, the turn-on electric field declines from 1.55 to 0.91 V/μm at an emission current density of 100 μA/cm², and the emission current density increases from 0.011 to 0.34 mA/cm² at an electric field of 1.0 V/μm. Both the brightness and uniformity of the CNT emission performance are improved after treatment.     

碳纳米管/硅纳米孔柱阵列的场发射性能

"通过热化学气相沉积的方法将碳纳米管生长到硅纳米孔柱阵列衬底上．采用场发射扫描电子显微镜、透射电子显微镜、高分辨透射电子显微镜、拉曼光谱和X射线能谱对所制备的样品形貌、组成进行了分析．结果发现：所制备产物为一种具有面积大、准周期性的碳纳米管/硅巢状阵列复合结构．能谱分析表明碳纳米管仅含有碳元素．对样品进行场发射性能测试表明该结构开启电压为1.3 MV/m,当外加电压为4.26 MV/m,发射电流为5 mA/cm2．由FN公式计算相应的场增强因子约为1.1￡104．碳纳米管/硅纳米孔柱阵列好的场发射性能被归