微型电子回旋共振离子推力器离子源结构优化实验研究

微型电子回旋共振(ECR)离子推力器可满足微小航天器空间探测的推进需求. 为此, 本文开展直径20 mm的微型ECR离子源结构优化实验研究. 根据放电室内静磁场和ECR谐振区的分布特点, 研究不同微波耦合输入位置对离子源性能的影响, 结果表明环形天线处在高于ECR谐振强度的强磁场区域时, 微波与等离子体实现无损耦合, 电子共振加热效果显著, 引出离子束流较大. 根据放电室电磁截止特性, 结合微波电场计算, 研究放电容积对离子源性能的影响, 实验表明过长或过短的腔体长度会导致引出离子束流下降甚至等离子体熄灭. 经优化后离子源性能测试表明, 在入射微波功率2.1 W、氩气流量14.9 μg/s下, 可引出离子束流5.4 mA, 气体放电损耗和利用率分别为389 W/A和15%.     

微型电子回旋共振离子源的全局模型

微型电子回旋共振(electron cyclotron resonance, ECR)离子源在紧凑型离子注入机、小型中子管、微型离子推进器等领域有着十分广泛的应用.为了深入认识微型ECR离子源的工作机理,本文以北京大学自主研制的一款微型氘离子源作为研究对象,以氢气和氘气放电形成的等离子体为例,发展了一种基于粒子平衡方程的全局模型.研究结果表明,该离子源束流成分与离子源的运行气压和微波功率有着很强的依赖关系.对于氢气放电等离子体,微波功率低于100 W时,离子源可以分别在低气压和高气压情况下获得离子比超过50%的H~+₂离子束和H~+₃离子束;当微波功率高于100 W时,可以在很宽的运行气压范围内,获得质子比超过50%的束流.因此,提高微波功率是提高微型离子源质子比的关键.对于氘气放电等离子体, 3种离子比例对运行气压和微波功率的依赖关系与氢气放电等离子体的规律基本一致.但是在相同的运行条件下, D~+比例比H~+比例高10%—25%.也就是说,在微型氘离子源的测试和优化过程中,可以利用氢气代替氘气进行实验,并将质子比测量结果作为相同条件下氘离...     

不同磁路电子回旋共振离子源引出实验

空间推进所用的电子回旋共振离子源(ECRIS)应具有体积小、效率高的特点. 本文研究的ECRIS使用永磁体环产生磁场, 有效减小了体积, 该离子源利用微波在磁场中加热电子, 电子与中性气体发生电离碰撞产生等离子体. 磁场在微波加热电子的过程中起关键作用, 同时影响离子源内等离子体的约束和输运. 通过比较四种磁路结构离子源的离子电流引出特性来研究磁场对10 cm ECRIS性能的影响. 实验发现: 在使用氩气的条件下, 特定结构的离子源可引出160 mA的离子电流, 最高推进剂利用率达60%, 最小放电损耗为120 W·A^-1; 所有离子源均存在多个工作状态, 工作状态在微波功率、气体流量、引出电压变化时会发生突变. 离子源发生状态突变时的微波功率、气体流量的大小与离子源内磁体的位置有关. 通过比较不同离子源的引出离子束流、放电损耗、气体利用率、工作稳定性的差异, 归纳了磁场结构对此种ECRIS引出特性的影响规律, 分析了其中的机理. 实验结果表明: 保持输入微波功率、气体流量、引出电压不变时, 增大共振区的范围、减小共振区到栅极的距离, 离子源能引出更大的离子电流; 减小共振区到微波功率入口、气体入口的距离能降低维持离子源高状态所需的最小微波功率和最小气体流量, 提高气体利用率, 但会导致放电损耗增大. 研究结果有助于深化对此类离子源工作过程的认识, 为其设计和性能优化提供参考.     

材料表面处理用强流电子回旋共振离子源

介绍一台2.45 GHz永磁强流电子回旋共振离子源,其外径160mm,高90 mm,放电室直径70 mm,高50 mm。微波馈入采用介质耦合方式,微波窗由一块f50 mm10 mm柱形BN和两块f30 mm10 mm的柱形陶瓷构成。离子源工作在脉冲模式下,采用三电极引出系统,最高引出电压达到100 kV,在微波输入功率300 W、进气量0.4 mL/min时,可引出峰值超过30 mA的氮离子束,在距离离子源引出孔1200 mm位置处的束流均匀区直径大于200 mm。     

微波电子回旋共振等离子体阴极电子束的实验研究

介绍了实验室研制的微波电子回旋共振(ECR)等离子体阴极电子束系统及初步研究结果，该系统包括微波ECR 等离子体源、电子束引出极、聚焦线圈等。通过测量水冷靶电流和靶上的束斑尺寸，实验研究了微波ECR 等离子体阴极电子束的流强、聚束性能等随电子束系统工作条件的变化。结果表明：微波输入功率越高、引出电压越高，引出电子束流强越大；工作气压对电子束流强的影响较复杂，随气压增加呈现出先降低后升高的特点；在7×10⁻⁴Pa 的极低气压下电子束流强可达75mA，引出电压9kV；能量利用率可达0.6；调整聚焦线圈的驱动电流，电子束的束斑直径从20mm 减小到13mm，电子束流强未有明显变化。     

磁场可调永磁离子源

研制了一台磁场可调微波离子源,在离子源放电室处需要的磁场由一组永久磁铁产生,永久磁铁外部安装了铁磁回路,铁磁回路的结构可以很容易的手动调整,通过调整铁磁回路的结构,可以在放电室产生要求的磁场.在调试过程中,也可以调整铁磁回路以改变离子源内部磁场结构,有利于获得最佳放电条件.该源在测试中,从3mm直径的引出孔引出了17mA的离子束.     

磁场可调永磁离子源

研制了一台磁场可调微波离子源, 在离子源放电室处需要的磁场由一组永久磁铁产生, 永久磁铁外部安装了铁磁回路, 铁磁回路的结构可以很容易的手动调整, 通过调整铁磁回路的结构, 可以在放电室产生要求的磁场. 在调试过程中, 也可以调整铁磁回路以改变离子源内部磁场结构, 有利于获得最佳放电条件. 该源在测试中, 从3mm直径的引出孔引出了17mA的离子束.     

ECR离子源束流引出与传输的研究

针对ECR离子源的束流引出及传输研究，在中国科学院近代物理研究所的LECR3离子源实验平台上开展了大量的实验. 实验中研究了等离子体电极引出孔径、反射电极(抑制电极)偏压以及Glaser透镜等因素对束流引出与传输的影响. 研究的重点是试图通过系列实验与分析来研究如何能更有效地引出强流离子束流并减小其在传输空间的损失. 给出了实验的主要结果，结合这些数据对ECR离子源的束流引出与传输进行了较全面的分析，并综合这些实验结果与分析结果得出了该物理过程的一般物理图像.     

HL-2A装置中性束离子源引出系统束流分析

在中性束离子源引出过程中,详细分析了引出束流的产生,这有利于得到更准确的引出功率和引出电极表面的热功率沉积情况。根据HL-2A装置中性束离子源引出电极的电连接方式和束流引出的物理过程,对离子源束流引出过程进行了分析,给出抑制极电流产生的主要来源。通过分析放电气压扫描实验中的结果发现:随着放电气压的增加,不同弧放电电流情况下抑制极电流均逐渐增加,且抑制极电流与引出电流的比值近似线性增加。针对引出离子束流经过引出电极的过程建立了物理模型。计算了抑制极电流与引出电流的比值与放电气压的依赖关系,计算结果与实验结果一致,验证了引出束流分析结果的合理性。     

低能辐照离子源的设计及性能

简要介绍了低能辐照离子源的设计及性能。采用热阴极磁约束ＰＩＧ放电，并用两极多孔加减速系统引出离子束。调试结果：离子束能量在２００－２０００ｅＶ范围内可调，最大引出速流１５０ｍＡ，灯丝工作寿命１６０ｈ。     

ORNL-HRIBF 6GHzECR离子源的最新结果

Experimental studies were conducted to characterize and improve the performance of the flat-B ECR ion source.The emittance of the source was investigated for the first time.The output beam currents of high-charge-states of Ar(q>8)were nearly doubled by increasing the plasma electrode aperture from 4mm to 6mm in diameter.To investigate possible enhancements with broadband microwave radiation,a"white"Gaussian noise generator was employed with a TWT amplifier to generate microwave radiation with a bandwidth of～200MHz.The performance of the flat-B ECR ion source was found to be much better with narrow bandwidth radiation when the source was operated in the flat-B region.However,the ion beam intensities and charge state distributions were improved with the broadband radiation when the source was tuned off the flat-B region.     

2.45 GHz ECR离子源的微波阻抗匹配

ECR离子源的等离子体阻抗对其微波传输与阻抗匹配设计至关重要。在中国科学院近代物理研究所现有的2.45 GHz ECR 质子源上,对等离子体阻抗进行了测量。首先用水吸收负载代替等离子体负载测量得到了所用微波窗阻抗,然后根据质子源测量数据,推算得到了等离子体阻抗。实验结果表明,脊波导输出端阻抗与后续负载不完全匹配,等离子体阻抗随微波功率变化呈非线性。这些结果为ECR离子源过渡匹配和微波窗的设计提供了参考依据。Plasma impedance of an ECR ion source is important for microwave transmission and impedance matching design. Plasma impedance was measured indirectly with the 2.45 GHz ECR proton source at the Institute of Modern Physics, Chinese Academy of Sciences. In the test, we got microwave window mpedance by using water absorption load instead of plasma load, and the source plasma impedance was derived from the test data with the 2.45 GHz ECR proton source and microwave window impedance. The experimental results show that ridge waveguide output impedance and the subsequent load does not exactly match, plasma impedance variation is nonlinear with microwave power. The achievedresult is useful in the design of ridged waveguide and microwave window.     

一台2.45GHz强流中子源

A 2.45GHz microwave-driven ion source is being used to provide 40mA of deuterium ion beam (peak current) for an RFQ accelerator as part of a neutron source system.We have also designed a 60kV electrostatic LEBT using computer simulations.In our experiment,we measured the hydrogen and deuterium ion beam currents as functions of discharge power,gas flow,and magnetic field strength.The required beam current was obtained using leas than 700W of net microwave power with a gas flow of less than 1.5sccm.From the rise time data,it was determined that in order to obtain a high percentage of atomic ions in the beam, the beam extraction should start after 1ms of switching on the microwave power.At steady state,the proton fraction was above 90%.     

第四代ECR离子源的主要概念(摘要)

To go beyond the present and planned third generation ECR ion sources operating at microwave frequencies between 20 and 30GHz to a fourth generation of sources operating above 50GHz offers new oppor- tunities and challenges.Based on the experimentally demonstrated frequency scaling,a doubling in operating frequency could provide more intense high charge state beams with higher charge states.The technical chal- lenges include the development of magnetic structures capable of producing 8T solenoid field and 4T sextupole fields,production and coupling of high power microwave power to heat the plasma,extraction of intense mul- tiple charge ion beams from a region of strong magnetic field and shielding of bremstrahlung from the hot electrons.In this paper,the status of high field superconducting magnets now under development for acceler- ator applications,gyrotrons for microwave power and other technical aspects that would be incorporated into a fourth generation ECR ion source are explored and applied to a conceptual design.     

宽带微波馈入对于具有常规磁场构型的ECR离子源性能的提高

As clearly demonstrated at several laboratories,the performances of electron-cyclotron resonance (ECR)ion sources can be enhanced by increasing the physical sizes(volumes)of embedded ECR zones.En- larged ECR zones have been achieved by engineering the central magnetic field region of these sources so they are uniformly-distributed"volumes"in resonance with single-frequency rf power.Alternatively,the number of ECR surfaces in conventional minimum-B geometry sources can be increased by heating their plasmas with multiple,discrete frequency microwave radiation.Broadband rf power offers a simple,low cost and arguably more effective means for increasing the physical sizes of the ECR zones within the latter source type.In this article,theoretical arguments are made in support of the volume effect and the charge-state enhancing ef- fects of broadband microwave radiation(bandwidth:200MHz)plasma heating are demonstrated by comparing the high-charge-states of Ar ion beams,produced by powering a conventional minimum-B geometry,6.4GHz ECR ion source,equipped with a biased disk,with those produced by conventional bandwidth(bandwidth:～1.5MHz)radiation.     

用于强流中子发生器的低能束流传输线的设计模拟

兰州大学设计研发的ZF-400强流中子发生器设计D-T中子产额6×1012 n/s,主要由ECR离子源、低能束流传输线（LEBT）、加速管、旋转靶等部分组成。LEBT负责将从离子源引出的束流进行分析聚焦并注入到加速管中。LEBT对束流的聚焦及分析的好坏程度决定了加速管中束流的损失程度、中子的产额以及靶的寿命。本工作就该强流中子发生器所需的低能传输线进行了设计。使用螺线管、分析磁铁和四极透镜组合的方案。利用TRACK软件对此方案进行模拟,得到符合要求的束流线及元件的参数。用TraceWin进行了验证模拟,验证结果符合要求。另外,通过软件模拟确定了杂质离子损失的位置,据此设计了束流管道冷却方案。通过模拟发现,这种透镜的组合方式可以让整个LEBT以较低的功率获得低损失、高纯度的打靶束流。The ZF-400 Intense Neutron Generator, which is designed by Lanzhou University with an expected neutron yield of 6×1012 n/s, is consist of ECR ion source, low energy beam transport (LEBT) line, accelerating tube and rotating target. The beam extracted from ECR source is analyzed and focused through LEBT, then, the beam is introduced into the accelerating tube. The focus and analysis ability of LEBT is very important for the beam loss, neutron yield and target's life. A LEBT line for intense neutron generator is designed in this paper, the project consisted of a solenoid, a bend magnet and three quadrupole lens. The qualified LEBT and its parameters have been got through the simulation with TRACK code. Then TraceWin program was employed to check this simulation and the result satisfied our requirement. Besides, the loss position of impurity ions was known through the simulation, and a project of beam line's cooling system was designed according to this result. Through the simulation, we find the optimal lens combination plan which can obtain lower beam loss and higher beam purity at low running power of LEBT.     

Electron-cyclotron-resonance plasma heating with broadband microwave radiation: Anomalous effects

Affects of microwave bandwidth on the high-charge-states of ion beams extracted from a conventional minimum-B-geometry ECR ion source are first demonstrated. The high-charge-state intensities, produced with broadband microwave radiation are observed to be factors ?2 than those produced with narrow bandwidth microwave radiation at the same power level.