p型导电掺In的SnO2薄膜的制备及表征

采用溶胶-凝胶提拉法成功地制备了p型导电掺In的SnO2薄膜.x射线衍射测试结果表明，掺In的SnO2薄膜保持SnO2的金红石结构.吸收谱测试结果表明，掺In的SnO2禁带宽度为3.8eV.霍尔测量结果表明，空穴浓度与热处理温度有很大的关系，525℃为最佳热处 理的温度.铟锡原子比在0.05—0.20范围内，空穴的浓度与In的含量有直接的关系，并随In含量的增加而增加. 关键词： SnO2 溶胶-凝胶法 p型导电     

Ⅲ族元素掺杂对SnO2电子结构及电学性能的影响

采用密度泛函理论研究了Ⅲ族元素掺杂对SnO2电子结构及电学性能的影响.态密度分析结果表明,以替代位存在的Ⅲ族杂质均使SnO2的费米能级明显向低能态方向移动,使得价带顶不完全填满,因此在SnO2中均充当受主作用.部分态密度分析结果表明,相对于掺Al的SnO2,Ⅲ族元素中的Ga及In对费米能级附近态密度贡献较大,其主要贡献来自Ga3d态或In4d态,这预示着在SnO2中掺Ga或In能实现更好的p型掺杂效果.电离能计算结果进一步表明,在Al,Ga及In三种元素中,替位In有最小的电离能(0.06 eV),这说明其在SnO2中能形成最浅的受主能级,因而在同等掺杂情况下,可引入最高浓度的空穴,从而实现最佳的p型掺杂效果.     

镁掺杂对In2O3电导和气敏性能的影响

用共沉淀法制备了Mg2 + 掺杂的In2 O3 纳米粉 ,研究了镁掺杂对In2 O3 电导和气敏性能的影响 .结果表明 :MgO和In2 O3 间可形成有限固溶体In2 -xMgxO3 (0≤x≤ 0 .40 ) ;MgIn× 电离的空穴对材料导带电子的湮灭 ,使掺镁纳米粉的电导变得很小 ;n(Mg2 + )∶n(In3 + ) =1∶2共沉淀物于 90 0℃下热处理 4h ,用所得的纳米粉制作的传感器在 32 0～ 370℃下 ,对 45 μmol/LC2 H5OH的灵敏度达 10 2 .5 ,为相同浓度干扰气体Petrol的 12倍多 .     

SnO_2/p~+-Si异质结器件的电致发光:利用TiO_2盖层提高发光强度

通过在重掺硼硅(p+-Si)衬底上溅射SnO2薄膜并在O2气氛下800℃热处理形成SnO2/p+-Si异质结.基于该异质结的器件可在低电压(电流)驱动下电致发光.进一步地,通过在SnO2薄膜上增加TiO2盖层,使器件的电致发光获得显著增强.这是由于TiO2盖层的引入,一方面使SnO2薄膜更加致密,减少了非辐射复合中心;另一方面TiO2较大的折射率和合适的厚度使SnO2薄膜电致发光的出光效率得到提高.     

掺钨VO_2薄膜的电致相变特性

采用直流磁控溅射与后退火工艺相结合的方法,在掺氟SnO_2(FTO)导电玻璃基底上制备了高质量的掺钨VO_2薄膜,对薄膜的结构、表面形貌和光电特性进行测试,分析了钨掺杂对其相变性能的影响.结果表明,室温下掺钨VO_2薄膜的阈值电压为4.2 V,观察到阈值电压下约有两个数量级的电流突变.随着温度升高,相变的阈值电压降低,且电流突变幅度减小.当施加8 V电压时,分别在不同温度下测试了掺钨VO_2薄膜的透过率.温度为20和50℃时,掺钨VO_2薄膜相变前后的红外透过率差量分别为23%和27%.与未掺杂的VO_2薄膜相比,掺钨VO_2薄膜具有相变温度低、阈值电压低和电阻率小的特点,在高速光电器件中有广阔的应用前景.     

Mg掺杂PST薄膜的溶胶-凝胶法制备及晶相形成研究

利用溶胶-凝胶法成功制备了Mg掺杂Pb_0.4Sr_0.6Mg_xTi< sub>1-xO_3-x薄膜，利用x射线衍射仪对薄膜的物相和结构进行了分析， 用扫描电子显微镜对薄膜的形貌和断面等进行了观察.研究结果表明，薄膜以立方钙钛矿为 晶相，薄膜中晶相以团聚状颗粒存在，晶相含量受热处理条件和Mg的掺杂量所控制.Mg掺杂 对Pb_0.4Sr_0.6Mg_xTi_1-xO_3-x 薄膜晶相含量的影响与钙钛矿中的氧空位缺陷相关.在一定的掺杂范围内，由掺杂引起晶相 的晶格畸变较小时，体系掺Mg平衡了晶体内本征氧空位引入的电荷不平衡，使晶相更为稳定 ，析晶能力提高，晶体形成量随掺杂浓度的提高而提高.当掺杂浓度达到一定量时， 随着Mg 掺杂浓度增加，一方面使形成晶体时杂质浓度增加造成参与形成晶相的组成含量下降，另一 方面使进入钙钛矿结构的Mg增加，氧空位大量增加使畸变程度提高，形成的晶相不稳定，析 晶能力下降，晶体含量随掺杂Mg浓度的增加而不增反降.在相同条件下制备的Pb_{0.4Sr0.6MgxTi1-xO3-x薄膜中Mg掺量约为 x=0.01时，得到的钙钛矿相含量最高，本征氧缺陷所带入的正电荷和Mg引入时带入的负电荷 间达到平衡.此外，Mg的掺入还影响到析晶与热处理过程之间的关系.在高Mg掺量范围，Mg含 量越高，形成的晶相越不稳定，热处理时间越长，使热处理过程中分解的晶相量越多，随Mg 掺量越高和热处理时间越长，薄膜中晶相含量越低. 关键词： 溶胶-凝胶法 PST薄膜 Mg掺杂 晶相形成}     

氧化铟掺铪红外透明导电薄膜

采用射频磁控溅射与退火工艺相结合的方法,分别在石英和硒化锌(ZnSe)衬底上制备了掺铪氧化铟(IHfO)薄膜,掺杂比例In2O3∶HfO2为98wt.%∶2wt.%.测试了薄膜的组成结构和3～5μm红外波段的光电性质,分析了退火温度、薄膜厚度和氧气流速对薄膜性能的影响.X射线衍射、扫描电子显微镜和X射线能谱表明,制备的IHfO薄膜具有氧化铟的立方体结构,掺杂铪并没有影响氧化铟的生长方向,但是减小了晶格间距,铪与铟外层电子形成新的杂化轨道.傅里叶变换红外光谱表明,随着退火温度的增加,IHfO薄膜在3～5μm波段的透过率逐渐下降,沉积在ZnSe衬底上的薄膜具有更平稳的透过率,厚度为100nm薄膜在3～5μm波段平均透过率为68%.测试霍尔效应表明,随着氧气流速的增加,IHfO薄膜电阻率逐渐增加,载流子浓度减小,霍尔迁移率变化不明显.晶界散射是影响IHfO薄膜迁移率的主要因素,当氧气流速为0.3sccm时,薄膜最佳电阻率为3.3×10~(-2)Ω·cm.与透可见光波段的导电氧化铟锡(ITO)薄膜相比,制备的IHfO薄膜可以应用在3～5μm红外波段检测气体,红外制导等领域.     

纳米晶SnO2透明导电薄膜的研制

阐述了金属氧化物透明导电薄膜研究的发展情况及其应用前景。介绍了采用磁控溅射技术 ,使用混合气体Ar和O2 ,在衬底温度为 15 0～ 40 0℃的耐热玻璃基片上制备纳米晶SnO2 :Sb透明导电薄膜 ,通过测定X射线衍射谱 ,表明薄膜择优取向为 [110 ]和 [2 11]方向。测量了SnO2 :Sb薄膜的导电特性随衬底温度及氧分压的变化。光学特性测量结果表明薄膜具有较高的透过率。     

紫外光下纳米TiO2薄膜亲水性机理的电化学研究

利用溶胶 凝胶方法在透明导电玻璃ITO (SnO2 ∶In)表面制备纳米TiO2 薄膜 ,XRD谱图表明TiO2 是锐钛矿晶型 ,AFM (Atomic Force Microscope)测得薄膜表面粒子约为 10 0nm .研究了ITO表面纳米TiO2 薄膜的光致亲水性变化 .通过循环伏安技术测定TiO2 薄膜电极在 2 5 3.7nm的紫外光照射后的电化学行为推测光致亲水性机理 .发现在紫外光照射一定时间后 ,TiO2 薄膜电极的循环伏安图在 +0 .0 35V处出现新的氧化峰 ;且随光照时间的增加 ,氧化峰的峰电流增大 ,溶液中的溶解氧对峰电流的大小有明显影响 .实验表明 ,在紫外光照下电极表面有Ti3 + 产生 ,证实了TiO2 薄膜的光致亲水性转变过程与Ti3 + 的生成导致的表面结构变化有关     

溶胶-凝胶法制备MgxZn1-xO薄膜的结构及光学特性

用溶胶-凝胶法制备了一系列的Mg_xZn_1-xO(0≤x≤0.3)薄膜,并用X射线衍射(XRD)和光致发光(PL)研究了不同的退火温度和Mg的掺杂含量对Mg_xZn_1-xO薄膜的结构和光学性质的影响.研究表明:Mg_xZn_1-xO薄膜为单相六角纤锌矿结构,并且具有沿c轴的择优取向;发现了中间热处理温度为350℃的Mg_xZn_1-xO薄膜退火温度的转折点为700℃,低于这个温度时随退火温度的升高,(002)衍射峰强度增强且掺Mg的薄膜既有紫外光又有绿光发射;800℃退火时,薄膜的(002)衍射峰强度减小,出现了(100)和(101)衍射峰,且掺Mg的薄膜只有紫外发光峰.不同的掺杂浓度对于发光也有影响,低于700℃退火时,ZnO薄膜只出现紫外发光峰,掺Mg的薄膜却出现了紫外和绿光两个发光峰.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.