Axial electric wake field inside the induction gap exited by the intense electron beam

While an intense electron beam passes through the accelerating gaps of a linear induction accelerator, a strong wake field will be excited. In this paper a relatively simple model is established based on the interaction between the transverse magnetic wake field and the electron beam, and the numerical calculation in succession generates a magnetic wake field distribution along the accelerator and along the beam pulse as well. The axial electric wake field is derived based on the relation between field components of a resonant mode. According to some principles in existence, the influence of this field on the high voltage properties of the induction gap is analyzed. The Dragon-I accelerator is taken as an example, and its maximum electric wake field is about 17 kV/cm, which means the effect of the wake field is noticeable.     

Experimental Investigation on Low Magnetic Field Operation of an Overmoded Slow-Wave High-Power Microwave Generator

The experimental results of an overmoded slow-wave high-power microwave generator operated at low magnetic field are presented. The feasibility of low magnetic field operation is investigated both theoretically and experimentally based on the characteristics of the overmoded slow-wave device. The experiments were carried out at the Spark-2 accelerator. Under the condition of guiding magnetic field strength of 0.55 T, diode voltage of 4 74 k V,and beam current of 5.2kA, a microwave was generated with power of 510 MW, mode of TM01, and frequency of 9.54 GHz. The relative half-width of the frequency spectrum is less than 1%, and the beam-to-microwave efficiency is about 21% in our experiments.     

CSR切割磁铁设计

兰州重离子加速器冷却储存环(HIRFL CSR)由一个主环(CSRm)和实验环(CSRe)构成.两个储存环的束流注入与引出都需要借助于切割磁铁的导向来完成.介绍了CSR的切割磁铁的物理设计和二维场计算. In order to satisfy the requirement of beam injection and extraction of CSR, four magnetic septums will be used in the accelerator. In the design, the shape of the lamination is optimized by 2-D magnetic field calculation. Also, in order to decrease the leakage field and obtain a satisfied field distribution, a special auxiliary coil and a shield iron plate are considered and as well as the construction of the septum leg is treated in a special way. As a result, the leakage field is almost...     

Magnetoelectric Coupling in Bilayers of Pb（Zr, Ti）O3 Epoxy and Hot Pressed Manganite Perovskite

The synthesis and magnetoclectric （ME） characterization of bilayers of Pb（Zr, Ti）O3 （PZT） and hot pressed manganite perovskite La0.7Sr0.3MnO3 （LSMO） are discussed. Very strong ME interactions are measured for the bilayers. The bilayers exhibit superior ME coupling compared to thick-film composites prepared by tape casting process. Data of the ME voltage coefficient have been obtained as functions of bias magnetic field H, temperature and frequency. The transverse coupling is stronger than the longitudinal interactions and a maximum in the ME voltage coefficient is measured at 225K. The frequency dependence of the ME voltage coefficient reveals a peak at the electromechanical resonance due to radial modes.     

High-field-induced electron detrapping in An AlGaN/GaN high electron mobility transistor

A step stress test is carried out to study the reliability characteristics of an AlGaN/GaN high electron mobility transistor(HEMT).An anomalous critical drain-to-gate voltage with a negative temperature coefficient is observed in the stress sequence,beyond which the HEMT device starts to recover from degradation induced by early lower voltage stress.While the performance degradation featuring the drain current slump stems from electron trapping in the surface or bulk states during low-to-medium bias stress,the recovery is attributed to high field induced electron detrapping.The carrier detrapping mechanism could be helpful for lessening the trapping-related performance degradation of a GaN-based HEMT.     

Measurment of the energy spectrum of an electron beam extracted from an accelerator

The electron energy spectrum is one of the most important characteristics of an electron beam that is extracted from a linear accelerator. The most direct way to determine an electron spectrum would be to use a magnetic spectrometer and this method could also give results with high precision and effectiveness. In this article we describe our design of a new multilayer absorption method, which is based on the depth-dose curves method that can be used in most irradiation accelerators,and adds the Monte Carlo simulation and iterative algorithm in order to reconstruct the electron energy spectrum. In this article the energy spectrum was measured using these two methods, and good results were acquired. These results could be crosschecked, which made the results more reliable.     

A new model analysis of the third harmonic voltage in inductive measurement for critical current density of superconducting films

The critical current density J c is one of the most important parameters of high temperature superconducting films in superconducting applications,such as superconducting filter and superconducting Josephson devices.This paper presents a new model to describe inhomogeneous current distribution throughout the thickness of superconducting films applying magnetic field by solving the differential equation derived from Maxwell equation and the second London equation.Using this model,it accurately calculates the inductive third-harmonic voltage when the film applying magnetic field with the inductive measurement for J c.The theoretic curve is consistent with the experimental results about measuring superconducting film,especially when the third-harmonic voltage just exceeds zero.The J c value of superconducting films determined by the inductive method is also compared with results measured by four-probe transport method.The agreements between inductive method and transport method are very good.     

Electron gun system for NSC KIPT linac

In the NSC KIPT linac, a neutron source based on a subcritical assembly driven by a 100 MeV/100 kW electron linear accelerator is under design and development. The linear accelerator needs a new high current electron gun. In this paper, the physical design, mechanical fabrication and beam test of this new electron gun are described.The emission current is designed to be higher than 2 A for the pulse width of 3 μs with repetition rate of 50 Hz.The gun will operate with a DC high voltage power supply that can provide a high voltage up to 150 kV. Computer simulations and optimizations have been carried out in the design stage, including the gun geometry and beam transport line. The test results of high voltage conditioning and beam test are presented. The operation status of the electron gun system is also included. The basic test results show that the design, manufacture, and operation of the new electron system are basically successful.     

Time-resolved energy spectrum measurement of a linear induction accelerator with the magnetic analyzer

We recently set up a time-resolved optical beam diagnostic system. Using this system, we measured the high current electron beam energy in the accelerator under construction. This paper introduces the principle of the diagnostic system, describes the setup, and shows the results. A bending beam line was designed using an existing magnetic analyzer with a 300 mm-bending radius and a 60° bending angle at hard-edge approximation. Calculations show that the magnitude of the beam energy is about 18 MeV, and the energy spread is within 2%. Our results agree well with the initial estimates deduced from the diode voltage approach.     

Multiple broadband magnetoelectric response in Terfenol-D/PZT structure

In this paper, a novel magnetoelectric(ME) composite structure is proposed, and the ME response in the structure is measured at the bias magnetic field up to 2000 Oe(1 Oe = 79.5775 A·m~(-1)) and the excitation frequency of alternating magnetic field ranging from 1 kHz to 200 kHz. The ME voltage of each PZT layer is detected. According to the measurement results, the phase differences are observed among three channels and the multi-peak phenomenon appears in each channel. Meanwhile, the results show that the ME structure can stay a relatively high ME response within a wide bandwidth.Besides, the hysteretic loops of three PZT layers are observed. When the frequency of alternating current(AC) magnetic field changes, the maximum value of ME coefficient appears in different layers due to the multiple vibration modes of the structure. Moreover, a finite element analysis is performed to evaluate the resonant frequency of the structure, and the theoretical calculating results accord well with the experimental results. The experiment results suggest that the proposed structure may be a good candidate for designing broadband magnetic field sensors.     

1.2 MV大功率直流高压电源研制

 采用等边三角形结构的铁芯，次级线圈分成40级，分别进行三相全波整流，每级输出直流30 kV，串联后获得1.2 MV/A的直流高电压大功率输出。电源的能量转换效率大于95%，漏抗高达21.7%。采用无滤波电容结构，次级线圈星型/三角型接法交替使用，纹波系数小于±4%。整个电源密封在压力钢筒中，充0.8 MPa高纯度SF6气体作为绝缘介质，最大工作场强小于130 kV/cm。设计了专门的SF6气体冷却系统，气体温度控制在60 ℃以内，高电压由充气同轴传输线输出。在小负载条件下，电源各项指标满足技术要求，已经安装在1.2 MW，1.2 MeV大功率直流电子加速器上进行整机联调。     

基于CSAPF的磁铁电源纹波抑制研究

加速器系统中由于大量非线性器件的存在产生了大量纹波,严重影响加速器磁场对粒子运动轨迹的控制。为实现对加速器直流电源纹波的抑制,相关研究主要集中在用电压型有源电力滤波器降低直流电源纹波,但该方法存在抑制精度不足、响应延时、开关设备损耗较大等问题。针对以上问题,本文比较了电流型和电压型有源电力滤波器的主电路拓扑结构,研究了电流型和电压型有源电力滤波器的脉冲宽度调制技术和控制策略,分析了在加速器系统中不同的有源电力滤波器对磁铁电源输出电流纹波的抑制性能。通过仿真分析与实验验证,发现电流型有源电力滤波器对磁铁电源输出电流纹波具有显著的抑制效果,并且电流型有源电力滤波器能够直接控制输出的纹波电流,纹波精度抑制更高,CSAPF投入后,负载电流纹波显著减小,电流纹波系数达到1.6×10–5。     

X波段短脉冲相对论返波管设计与初步实验

 对基于短电子束脉冲超辐射机理的X波段相对论返波管进行了优化设计和粒子模拟，结果表明：在超辐射机理作用下，该器件能实现高峰值功率和高功率转换效率的微波辐射。在小型Tesla脉冲源基础上设计了阻抗变换段、二极管、磁场系统等装置，建立了一套小型窄脉冲电子加速器，以此为实验平台在低磁场条件下进行了器件的初步实验研究。在磁场0.73 T、束压约380 kV、束流约4.5 kA、脉宽3.1 ns条件下，实验获得的微波脉冲峰值功率约360 MW，脉宽1.10 ns，上升沿800 ps，频率9.15 GHz，功率转换效率为21%。     

Axial electric wake field inside the induction gap exited by the intense electron beam

While an intense electron beam passes through the accelerating gaps of a linear induction accelerator,a strong wake field will be excited.In this paper a relatively simple model is established based on the interaction between the transverse magnetic wake field and the electron beam,and the numerical calculation in succession generates a magnetic wake field distribution along the accelerator and along the beam pulse as well.The axial electric wake field is derived based on the relation between field components of a resonant mode.According to some principles in existence,the influence of this field on the high voltage properties of the induction gap is analyzed.The Dragon-I accelerator is taken as an example,and its maximum electric wake field is about 17 kV/cm,which means the effect of the wake field is noticeable.     

300kV的虚火花放电实验

 介绍了用脉冲线加速器作驱动电源产生高压虚火花放电的实验。脉冲线加速器由十级马克斯发生器和改装的脉冲形成线构成, 虚火花放电室中注入低气压氮气, 在300kV的放电电压下获得药10kA的高亮度电子束。     

快脉冲高电压大电流测量探头标定方法

基于脉冲形成原理提出了一种快脉冲高电压大电流测量探头的在线标定方法。利用闪光二号加速器输出线和二极管作为脉冲形成线,结合研制的低电感开关和负载,产生一个前沿小于3 ns、脉宽20 ns的准方波,对二极管电压测量探头微分型电容分压器和电流测量探头微分环进行了在线标定,得到测量探头在实际使用环境中的时间响应小于4 ns。该方法消除了非在线标定环境和实际环境无法统一对标定结果的影响,可推广应用于传输线型脉冲功率装置的探头标定。     

1.5MeV LIA脉冲功率系统

本文简要介绍了1.5MeV LIA脉冲功率系统的结构、组成和设计思想;给出了开关运行参数和确定开关时间抖动指标的方法、闭环系统的总抖动对加速电压相对变化的影响、脉冲功率系统各段输出波形和电压幅度的调制关系;测量结果表明,1.5MeV LIA的运行功率和时间同步满足总体设计要求。     

重复脉冲强流电子束传输技术研究

分析并推导出了环形强流电子束的稳定传输条件，通过静电磁场模拟计算对CHP01强流电子加速器二极管引导磁场的位形分布、幅值大小及磁场电源进行了优化设计.经实验调试及束斑测量，表明设计的1秒磁场满足束流稳定传输条件，能使电压800kV、电流8kA、脉冲宽度40ns、脉冲重复频率100Hz的环形强流电子束稳定传输，并已成功运用于CHP01强流电子加速器束流传输系统. 关键词： 束流传输 引导磁场 二极管 重复脉冲 电子束     

A 1-MW, 1-mm continuous-wave FELtron for toroidal plasma heating

A powerful, continuous-wave millimeter radiation source is presented. An electrostatic Cockcroft-Walton accelerator (2.5 MV) drives an FEL (free-electron laser) of 1 MW power. The accelerator has a new design in order to obtain a very powerful (50 MW) electron beam and very small ripple. A recovery system is used to increase RF power and efficiency. The FEL oscillator is 1.5-m long, with a permanent magnet helical wiggler. The cavity is equipped with Bragg mirrors. The FEL is set at the high voltage terminal