In-plane anisotropy in two-dimensional electron gas at LaAlO_3/SrTiO_3(110) interface

A systematic study of the two-dimensional electron gas at La AlO_3/SrTiO_3(110) interface reveals an anisotropy along two specific directions, [001] and 1ī0. The anisotropy becomes distinct for the interface prepared under high oxygen pressure with low carrier density. Angular dependence of magnetoresistance shows that the electron confinement is stronger along the 1ī0 direction. Gate-tunable magnetoresistance reveals a clear in-plane anisotropy of the spin–orbit coupling,and the spin relaxation mechanism along both directions belongs to D'yakonov–Perel'(DP) scenario. Moreover, in-plane anisotropic superconductivity is observed for the sample with high carrier density, the superconducting transition temperature is lower but the upper critical field is higher along the 1ī0 direction. This in-plane anisotropy could be ascribed to the anisotropic band structure along the two crystallographic directions.     

PREPARATION OF a-AXIS ORIENTED YBa2Cu3Ox THIN FILMS

The a-axis oriented YBa₂Cu₃O_x(YBCO) thin films could be grown on (100) SrTiO₃(STO) substrates with STO buffer layers by dc and rf magnetron sputtering either by low-ering the deposition temperature, or by using a self-template technique. For the latter, the resistivity of the thin film at 290K along the substrate [001] direction is about four times larger than that in the [010] direction. The zero resistance temperatures T_c0 are 89 K in both directions. So high quality a-axis oriented YBCO thin films can be prepared by the self-template technique. Also the T_c0 increase monotonously with the reduction of the thickness of the YBCO seed layer.     

金红石TiO_2中本征缺陷扩散性质的第一性原理计算

基于密度泛函理论的爬坡弹性带方法,对金红石相二氧化钛晶体中钛间隙、钛空位、氧间隙、氧空位4种本征缺陷的扩散特征进行了研究.对比4种本征缺陷在晶格内部沿不同扩散路径的过渡态势垒后发现,缺陷扩散过程呈现出明显的各向异性.其中,钛间隙和氧间隙沿[001]方向具有最小的扩散势垒路径,激活能分别为0.505 eV和0.859 eV;氧空位和钛空位的势垒最小的扩散路径分别沿[110]方向和[111]方向,激活能分别为0.735 eV和2.375 eV.     

(100)Si基应变p型金属氧化物半导体[110]晶向电导率有效质量双椭球模型

利用应变技术和沟道晶向工程技术,均可有效增强Si基金属氧化物半导体器件的性能.本文提出了(100)Si p型金属氧化物半导体(PMOS)[110]晶向电导率有效质量双椭球模型,从理论上解释了Si PMOS[100]晶向沟道空穴迁移率为[110]晶向沟道空穴迁移率1.15倍的原因.基于(100)Si基应变PMOS反型层E-k关系,拓展应用该模型,首先获得了(100)Si基应变PMOS反型层价带第一子带等能图,然后给出了(100)Si基应变PMOS器件反型层[110]晶向空穴电导率有效质量模型.本文的模型方案合理可行,可为Si基应变PMOS器件的研究与设计提供有价值的参考.     

Fabrication and characteristics of all YBCO sandwich-type junctions using highly crystalline DC sputtered superconducting a-axis oriented Y1Ba2Cu3O7-x films

We report on the fabrication and characteristics of sandwich-type tunnel junctions with highly crystalline sputtered a-axis oriented thin film of Y₁Ba₂Cu₃O_7-x (YBC) as the base and the counter electrode. The junctions have been fabricated on SrTiO₃ (100) and MgO (100) substrates. A non-superconducting phase of YBC corresponding to a lattice constant of 4.08 Å is used as the barrier layer making this an all YBC sandwich junction. For all temperatures below T_ce (R=0) of the device, a zero voltage current was observed. The critical current density (J_c) of the device was found to be dependent on the thickness of the barrier layer and the crystallinity of the a-axis oriented YBC electrodes. At 40 K, such a junction fabricated on a SrTiO₃ (100) substrate was found to have a J_c of 1.8 X 10⁴ A/cm² and an I_cR_n product of 0.2 mV.     

Stability and electronic structure studies of LaAlO_3/SrTiO_3 (110) heterostructures

The first-principles calculations are employed to investigate the stability, magnetic, and electrical properties of the oxide heterostructure of LaAlO3/SrTiO3(110). By comparing their interface energies, it is obtained that the buckled interface is more stable than the abrupt interface. This result is consistent with experimental observation. At the interface of LaAlO3/SrTiO3(110) heterostructure, the Ti–O octahedron distortions cause the Ti t2 gorbitals to split into the twofold degenerate dxz/dyz and nondegenerate dxy orbitals. The former has higher energy than the latter. The partly filled two-fold degenerate t2 gorbitals are the origin of two-dimensional electron gas, which is confined at the interface. Lattice mismatch between LaAlO3 and SrTiO3leads to ferroelectric-like lattice distortions at the interface, and this is the origin of spin-splitting of Ti 3d electrons. Hence the magnetism appears at the interface of LaAlO3/SrTiO3(110).     

LaTiO3(110)薄膜分子束外延生长的精确控制和表面截止层的研究

LaTiO₃ 是一种典型的强关联电子材料, 其(110) 薄膜为通过晶格对称性、应变等的设计调控外延结构的物理性质提供了新的机会. 本文研究了SrTiO₃(110) 衬底表面金属La 和Ti 沉积所引起的微观结构变化, 进而利用电子衍射信号对分子束外延薄膜生长表面阳离子浓度的灵敏响应, 发展了原位、实时、精确控制金属蒸发源沉积速率的方法, 实现了高质量LaTiO₃(110) 薄膜的生长和对阳离子化学配比的精确控制. 由于LaTiO₃中Ti³⁺ 3d 电子的库仑排斥作用, 氧原子层截止的(110) 表面更容易实现极性补偿, 因此生长得到的薄膜表面暴露出单一类型的氧截止面.     

Thickness dependence of microstructures in La0.9Sr0.1MnO3 thin films grown on exact-cut and miscut SrTiO3 substrates

The thickness dependence of microstructures of La_0.9Sr_0.1MnO₃ (LSMO) thin films grown on exact-cut and miscut SrTiO₃ (STO) substrates, respectively, was investigated by high-angle X-ray diffraction (HXRD), X-ray small-angle reflection (XSAR), X-ray reciprocal space mapping and atomic force microscopy (AFM). Results show that the LSMO films are in pseudocubic structure and are highly epitaxial [0 0 1]-oriented growth on the (0 0 1) STO substrates. The crystalline quality of the LSMO film is improved with thickness. The epitaxial relationship between the LSMO films and the STO substrates is [0 0 1]_LSMO[0 0 1]_EXACT-STO, and the LSMO films have a slight mosaic structure along the q_x direction for the samples grown on the exact-cut STO substrates. However, an oriented angle of about 0.24° exists between [0 0 1]_LSMO and [0 0 1]_MISCUT-STO, and the LSMO films have a mosaic structure along the q_z direction for that grown on the miscut STO substrates. The mosaic structure of both groups of the samples tends to reduce with thickness. The diffraction intensity of the (0 0 4) peaks increases with thickness of the LSMO film. The XSAR and AFM observations show that for both groups, the interface is sharp and the surface is rather smooth. The mechanism was discussed briefly.     

Anomalous temperature dependence of magnetization in single-crystal Fe65Ni35 alloy

Magnetization (0–10 Oe) and magnetic relaxation measurements were carried out in the temperature range between 4.2 and 300 K for three picture-frame samples of Fe₆₅Ni₃₅ alloy whose edges were parallel to 100, 110 and 111, respectively. The typical temperature T_g and the magnetic field H_g which correspond to the anomalous temperature in the χ-T curve and inflection field in the σ-H curve, respectively are summarized and H-T_g and H_g-T diagrams are obtained. A strong magnetic relaxation is observed along the H_g-T line. The dependence of H_g on the crystallographic direction and on the temperature are discussed by the thermal activation process of the 180° domain wall which is pinned strongly by the antiferromagnetic clusters below T_g. The anomaly of magnetization of Fe₆₅Ni₃₅ alloy can be interpreted by the macroscopic picture of the coexistence of ferromagnetic and antiferromagnetic-like regions which may be caused by a statistical fluctuation of alloy composition.     

First-principles study of electronic structure and magnetic properties of SrTi1−xMxO3 (M= Cr,Mn, Fe,Co, or Ni)

We used first-principles calculations to conduct a comparative study of the structure and the electronic and magnetic properties of SrTiO₃ doped with a transition metal (TM), namely, Cr, Mn, Fe, Co, or Ni. The calculated formation energies indicate that compared with Sr, Ti can be substituted more easily by the TM ions. The band structures show that SrTi_0.875Cr_0.125O₃ and SrTi_0.875Co_0.125O₃ are half metals, SrTi_0.875Fe_0.125O₃ is a metal, and SrTi_0.875Mn_0.125O₃ is a semiconductor. The 3d TM-doped SrTiO₃ exhibits various magnetic properties, ranging from ferromagnetism (Cr-, Fe-, and Co-doped SrTiO₃) to antiferromagnetism (Mn-doped SrTiO₃) and nonmagnetism (Ni-doped SrTiO₃). The total magnetic moments are 4.0_μB, 6.23_μB, and 2.0_μB for SrTi_0.75Cr_0.25O₃, SrTi_0.75Fe_0.25O₃, and SrTi_0.75Co_0.25O₃, respectively. Room-temperature ferromagnetism can be expected in Cr-, Fe-, and Co-doped SrTiO₃, which agrees with the experimental observations. The electronic structure calculations show that the spin polarizations of the 3d states of the TM atoms are responsible for the ferromagnetism in these compounds. The magnetism of TM-doped SrTiO₃ is explained by the hybridization between the TM-3d states and the O-2p states.     

单晶CeB_6发射性能及磁电阻各向异性研究

采用X射线劳厄定向法对单晶CeB_6的(110),(111),(210)和(310)晶面进行了定向.系统研究了不同晶面热发射性能及磁场对电阻率的影响规律.结果表明,当阴极温度为1873 K时(110),(111),(210)和(310)晶面最大发射电流密度分别为38.4,11.54,50.4和20.8 A/cm~2,表现出了发射性能的"各向异性".RichardsonDushman公式计算逸出功结果表明,上述晶面中(210)晶面具有最低的逸出功,为2.4 eV.从实际应用来看,该晶面有望替代商业化的钨灯丝成为新一代的场发射阴极材料.磁电阻率测量结果显示,当晶体从[001]方向旋转至[011]方向时电阻率从73μ?·cm变化至69μ?·cm,表明电阻率在磁场中沿不同方向同样具有"各向异性"的特点.     

A reversible reaction forming (---Cu---O---) strings and (Cu)6-clusters on Ag(110) shown by STM

An artificial new surface of (---Cu---O---) chains grown on Ag(110) surface was prepared by reacting a surface with Cu atoms, where the (---Cu---O---) chains grow in the [1 0] direction and are self-assembled on the Ag(110) surface in a (2 x 2)-p2mg structure. When the Cu---O/Ag(110) surface was heated in vacuum, the (---Cu---O---) chain decomposed to uniform cluster dots arranged along the [1 0] direction, where the cluster dots were composed of six Cu atoms. When the Ag(110) surface with the Cu---cluster dots was exposed to O₂, the (---Cu---O---) lines were redrawn along the [1 0] direction by reacting a s in the [1 0] direction with O₂. This is a reversible chemical reaction in one dimensional regime proved in atomic resolution.     

Aspects of “low field” magnetotransport in epitaxial thin films of the ferromagnetic metallic oxide SrRuO3

Epitaxial thin films of the conductive ferromagnetic oxide SrRuO₃ were grown on an (0 0 1) SrTiO₃ (STO) substrate by using DC sputtering technique. The magnetic and magnetoresistive properties of the films were measured by applying the magnetic field both perpendicular (out-of-plane) and parallel (in-plane) to the film plane and ever maintaining the direction of the applied field perpendicular to that of the transport current. The films grown on an (0 0 1) STO substrate showed identical magnetization properties in two orthogonal crystallographic directions of the substrate, [1 0 0]_S and [0 0 1]_S (in-plane and out-of-plane geometry), which suggests the presence of a multi domain structure within the plane of the film. For such samples, no anisotropic field (hard axis) along de [0 0 1]s direction, i.e., perpendicular to the film-plane could be detected. Nevertheless, a distinguishable temperature dependent out-of-plane anisotropic magnetoresistance (MR) along with strong temperature dependent low field hysteretic MR(H) behavior was detected for the studied films. A negative MR ratio MR(T)=[ρ(μ₀H=9 T; T)−ρ( μ₀H=0 T; T)]/ρ( μ₀H=0 T; T) on the order of a few percent, with maximums of 6% and 4% (right at the Curie temperature, T_C 160 K) was calculated for an in-plane and out-of plane measuring geometry, respectively. In addition there is an equally strong MR effect at low temperatures, which might be related to the temperature dependence of the magnetocrystalline anisotropy together with a magnetization rotation. Both the MR(T) behavior and the achieved values (except for T<30 K) are similar to those obtained on SrRuO₃ films grown on 2° miscut (0 0 1) STO substrates with the current parallel to the field and parallel to the direction, which was identified as the easier axis for magnetization.     

SUPERCONDUCTING PROPERTIES AND STRUCTURAL PERFECTION OF EPITAXIAL YBa2Cu3O7-x THIN FILMS

High quality epitaxial YBa₂Cu₃O_7-x thin films have been succcessfully prepared by dc magnetron sputtering deposition, on (100) and (110) aligned SrTiO₃, LaAlO₃ and yttria-stabilized zirconia (YSZ) substrates. The films showed zero resistance around 90 K and had a J_c (at 77 K, H=0) over 10⁶A/cm². It was found that superconducting properties and structures of the films were strongly dependent on oxygen pressure and substrate temperature. The epitaxial structure of the films have been studied by X-ray diffraction. Rutherford backscattering and channeling spectroscopy, X-ray double-crystal diffraction and transmission election microscopy. The experimental results demonstrated that the epitaxial YBa₂Cu₃O_7-x films had excellent superconducting properties and quite perfect structure.     

Sign reversal of anisotropic magnetoresistance and anomalous thickness-dependent resistivity in Sr2CrWO6/SrTiO3 films

High-quality Sr₂CrWO₆ (SCWO) films have been grown on SrTiO₃ (STO) substrate by pulsed laser deposition under low oxygen pressure. With decrease of the film thickness, a drastic conductivity increase is observed. The Hall measurements show that the thicker the film, the lower the carrier density. An extrinsic mechanism of charge doping due to the dominance of oxygen vacancies at SCWO/STO interfaces is proposed. The distribution and gradient of carrier concentration in SCWO films are considered to be related to this phenomenon. Resistivity behavior observed in these films is found to follow the variable range hopping model. It is revealed that with increase of the film thickness, the extent of disorder in the lattice increases, which gives a clear evidence of disorder-induced localization charge carriers in these films. Magnetoresistance measurements show that there is a negative magnetoresistance in SCWO films, which is considered to be caused by the magnetic scattering of magnetic elements Cr³⁺ and W⁵⁺. In addition, a sign reversal of anisotropic magnetoresistance (AMR) in SCWO film is observed for the first time, when the temperature varies across a characteristic value, T_M. Magnetization—temperature measurements demonstrate that this AMR sign reversal is caused by the direction transition of easy axis of magnetization from the in-plane ferromagnetic order at T > T_M to the out-of-plane at T < T_M.     

Temperature-dependent surface X-ray diffraction on K/Ag(001)-(2 × 1)

Temperature-dependent surface X-ray diffraction experiments have been performed on the K/Ag(001)-(2 × 1) adsorption system. The structure is characterized by a missing-row geometry in which alternate Ag rows along [1 0] are missing. The K atoms reside within the large grooves coordinated by six Ag atoms at a distance of 3.44(5) Å, corresponding to an effective K-radius of 2.00(5) Å. Large anisotropic disorder is observed for both the K-atoms and the top-layer (“ridge”) Ag atoms. The K-atom displacements are largest in the direction along the grooves, whereas for the Ag atoms the vibrations along [110] are significantly larger. The temperature dependence of the Ag vibrations is in accordance with Debye theory for the [110] direction, but deviates from it for the [1 0] vibrations at high temperature. In contrast to the K-atoms, the out-of-plane vibrations of the top-layer Ag atoms are larger than the in-plane vibrations. The inclusion of anharmonic contributions to describe the Ag disorder significantly improves the fits. It is shown that if anharmonicity is neglected the interlayer contraction is overestimated (Δd₁₂/d₁₂ only −3.2%, instead of −12.7% if anharmonicity is neglected). Due to the anharmonicity, different definitions of the atomic position arise (mean, mode and equilibrium position), which are discussed on the basis of the results.     

Study of scanning tunneling microscopy images and probable relaxations of the SrTiO3(100) surface by electronic structure calculations

Partial electron density plots were calculated for a model SrTiO₃(100) surface with √5 × √5 ordered oxygen vacancy to examine why the bright spots of the scanning tunneling microscopy (STM) images of SrTiO₃(100) observed in ultrahigh vacuum (UHV) correspond to the oxygen vacancy sites. Possible dependence of the image on the polarity and magnitude of the bias voltage was also discussed on the basis of partial electron density plot calculations. Our study strongly suggests that the UHV STM imaging involves the lowest-lying d-block level of every two Ti³⁺ centers adjacent to an oxygen vacancy, the tip-sample distance involved in the UHV STM experiments is substantially larger than that involved in typical ambient-condition STM imaging, and the Ti⁴⁺ and Ti³⁺ sites of SrTiO₃(100) are reconstructed.     

Al纳米线不同晶向力学行为和变形机制的模拟

采用分子动力学模拟计算方法,考察具有较高层错能的Al纳米线沿不同晶向的力学行为和变形机制。在相同计算条件下与具有较低层错能的Ni、Cu、Au和Ag等FCC金属纳米线进行比较。结果表明：在力学行为方面,Al纳米线的弹性模量呈现明显的结构各向异性,满足E_[111] > E_[110] > E_[100]的关系,这一关系在FCC金属纳米线中普遍成立;Al纳米线的屈服应力随晶向呈现σ_y[100] > σ_y[111] > σ_y[110]的关系,这一关系在具有较低层错能的FCC金属纳米线中不具有普遍性,这与体系中位错形成机制密切相关。根据拉伸变形过程微观结构的演变规律,阐明Al纳米线不同晶向的变形机制,并与具有较低层错能的Ni、Cu、Au和Ag等FCC金属纳米线的变形机制进行比较。结果表明,对于尺度较小的高层错能Al纳米线,Schmid因子和广义层错能均难以准确预测其变形机制。     

无铅四方相钙钛矿短周期超晶格压电效应机理研究

超晶格压电行为与内部正离子之间的内在联系尚缺乏相关的研究.本文基于密度泛函理论的第一性原理方法,研究了三种无铅四方相钙钛矿铁电超晶格(BaTiO_3/SrTiO_3,KNbO_3/KTaO_3和BaTiO_3/KNbO_3)中A,B位正离子对整体的极化和压电贡献.通过计算超晶格不同轴向应变条件下原子结构和Born有效电荷,获得了超晶格和各个正离子的极化值和压电系数.结果表明,在轴向压缩应变条件下(-0.15—0 A),无铅超晶格中的正离子位移D(A)和D(B)受到抑制,在拉应变时位移才显著增大,因此极化和压电行为不明显.在轴向拉伸应变作用下(0—0.15 A),无铅超晶格中各原子的极化贡献显著增大,特别是B位原子Ti,Nb和Ta的极化贡献使得总的极化强度也显著提高,并当拉应变达到一定值,超晶格才会出现明显的压电行为.无铅超晶格的极化和压电行为主要由B位正离子贡献.