多层膜［Co85Cr15/Pt］20的磁性、垂直磁记录特性和微结构的关系

采用磁控溅射法制备了性能优良的以Pt为缓冲层的［Co85₈₅Cr15_{15/Pt］2020 多层膜，研究了溅射气压对［Co8585Cr1515/Pt］2020多层膜微结构和磁性的 影响.研究结果表明，Ar溅射气压对［Co8585Cr1515/Pt］2020多层膜的微结构 、垂直磁各向异性和矫顽力有重要的影响 关键词： 溅射气压 多层膜 垂直磁各向异性 有效磁各向异性常数}     

引入纳米氧化层的CoFe/Pd双层膜结构中增强的垂直磁各向异性研究

制备了CoFe/Pd双层结构的界面处或CoFe层 内部引入纳米氧化层后的系列薄膜. 研究结果显示, 引入纳米氧化层后, 可以使薄膜的磁各向异性在退火后从面内转到垂直膜面方向. 并且对于在CoFe层内部引入纳米氧化层的这类样品, 其强烈的垂直磁性可以在相当宽的有效磁性层厚度范围内(1.2-2 nm)维持. 在保持垂直磁性的前提下, 这种特殊的双层膜结构中CoFe磁性层厚度比常规CoFe/Pd 多层膜中的CoFe层厚度至少多出1.4 nm. 本文的研究有助于制备出具有较高热稳定性的垂直磁性器件电极.     

Ultrathin (CoFe/Pt)n multilayers with tuned magnetic properties

Perpendicular magnetic anisotropy (PMA) has been investigated in ultrathin (CoFe [0.2] nm/Pt [0.2] nm)_n multilayers. The Pt layers show an fcc crystal structure with a preferred [111] orientation. The multilayers with n=3, 4 show PMA in the as-grown state, which can be enhanced by thermal annealing. However, no PMA is observed in the as-grown state with higher repetitions (n>&=5), although it is observed after thermal annealing. For 1=&<n=&<8, the anisotropy energy is around 10⁵ J/m³ for all (CoFe [0.2]/Pt [0.2])_n stacks. The perpendicular anisotropy is related to layer thickness and interface roughness.     

具有垂直各向异性(Pt/Co)n/FeMn多层膜的交换偏置

采用磁控溅射方法制备了以Pt为缓冲层和保护层的具有垂直各向异性(Pt/Co)_n/ FeMn多层膜.研究结果表明，多层膜的垂直交换偏置场H_ex和反铁磁层厚度的关 系与其具有平面各向异性的交换偏置场随反铁磁层厚度变化趋势相近.随着铁磁层调制周期 数的增加，垂直交换偏置场H_ex相应减小，并且与铁磁层的调制周期数近似成反 比关系.(Pt/Co)₃/FeMn的垂直交换偏置场H_ex已经达到22.3kA/m.为 关键词： 交换偏置 垂直各向异性 多层膜     

Co/Ni多层膜垂直磁各向异性的研究

采用直流磁控溅射法在玻璃基片上制备了Pt底层的Co/Ni多层膜样品, 对影响样品垂直磁各向异性的各因素进行了调制, 通过样品的反常霍尔效应系统的研究了Co/Ni多层膜的垂直磁各向异性. 结果表明, 多层膜中各层的厚度及周期数对样品的反常霍尔效应和磁性有重要的影响. 通过对多层膜各个参数的调制优化, 最终获得了具有良好的垂直磁各向异性的Co/Ni多层膜最佳样品Pt(2.0)/Co(0.2)/Ni(0.4)/Co(0.2)/Pt(2.0), 经计算, 该样品的各向异性常数K_eff 达到了3.6×10⁵ J/m³, 说明样品具备良好的垂直磁各向异性. 最佳样品磁性层厚度仅为0.8 nm, 样品总厚度在5 nm以内, 可更为深入的研究其与元件的集成性.     

Antiferromagnet IrMn thickness dependence in exchange-biased perpendicular magnetic anisotropy based on CoFe/Pt/CoFe/[IrMn(tIrMn)] multilayers

The effect of the antiferromagnetic IrMn thickness upon the magnetic properties of CoFe/Pt/CoFe/[IrMn(t_IrMn)] multilayers is studied. An oscillatory interlayer coupling (IEC) has been shown in pinned CoFe/Pt(t_Pt)/CoFe/IrMn multilayers with perpendicular anisotropy. The period of oscillation corresponds to about 2 monolayers of Pt. The oscillatory behavior of IEC depends on the nonmagnetic metallic Pt thickness and is thought to be related to the antiferromagnetic ordering induced by the IrMn layer. From the extraordinary Hall voltage amplitude (EHA) curves as function of IrMn thickness, we report that the oscillation dependence of IEC for the [CoFe/Pt/CoFe] multilayer system induced by IrMn with spacer-layer thickness is a important features of perpendicular exchange biased system.     

CoFeB/Pt多层膜的垂直磁各向异性研究

具有垂直磁各向异性的磁性纳米结构是自旋转移力矩器件的重要研究内容, 本文采用反常霍尔效应系统地研究了磁控溅射法制备的[CoFeB/Pt]_n多层膜的垂直磁各向异性. 当CoFeB的厚度小于0.6 nm时, 可以在[CoFeB/Pt]_n多层膜中观察到清晰的垂直磁各向异性, 其垂直磁各向异性强烈依赖于CoFeB和Pt层厚度及多层膜周期数. 当多层膜周期数n ≥ 5时, 出现零剩磁现象. 另外, [CoFeB/Pt]_n多层膜的矫顽力均小于2 kA·m^-1, 有望作为垂直自由层的重要侯选材料应用于垂直磁纳米结构中.     

Magnetic properties of a Pt/Co₂ FeAl/MgO structure with perpendicular magnetic anisotropy

Microstructures and magnetic properties of Ta/Pt/Co 2 FeAl(CFA)/MgO multilayers are studied to understand perpendicular magnetic anisotropy(PMA) of half-metallic full-Heusler alloy films.PMA is realized in a 2.5-nm CFA film with B2-ordered structure observed by a high resolution transmission electron microscope.It is demonstrated that a high quality interface between the ferromagnetic layer and oxide layer is not essential for PMA.The conversions between in-plane anisotropy and PMA are investigated to study the dependence of magnetic moment on temperature.At the intersection points,the decreasing slope of the saturation magnetization(M s) changes because of the conversions.The dependence of M s on the annealing temperature and MgO thickness is also studied.     

Magnetic anisotropy manipulation and interfacial coupling in Sm3Fe5O12 films and CoFe/Sm3Fe5O12 heterostructures

The magnetic anisotropy manipulation in the Sm₃Fe₅O₁₂ (SmIG) films and its effect on the interfacial spin coupling in the CoFe/SmIG heterostructures were studied carefully. By switching the orientation of the Gd₃Ga₅O₁₂ substrates from (111) to (001), the magnetic anisotropy of obtained SmIG films shifts from in-plane to out-of-plane. Similar results can also be obtained in the films on Gd₃Sc₂Ga₃O₁₂ substrates, which identifies the universality of such orientation-induced magnetic anisotropy switching. Additionally, the interfacial spin coupling and magnetic anisotropy switching effect on the spin wave in CoFe/SmIG magnetic heterojunctions have also been explored by utilizing the time-resolved magneto-optical Kerr effect technique. It is intriguing to find that both the frequency and effective damping factor of spin precession in CoFe/SmIG heterojunctions can be manipulated by the magnetic anisotropy switching of SmIG films. These findings not only provide a route for the perpendicular magnetic anisotropy acquisition but also give a further path for spin manipulation in magnetic films and heterojunctions.     

Magnetic properties of a Pt/Co2FeAl/MgO structure with perpendicular magnetic anisotropy

Microstructures and magnetic properties of Ta/Pt/Co 2 FeAl（CFA）/MgO multilayers are studied to understand perpendicular magnetic anisotropy（PMA） of half-metallic full-Heusler alloy films.PMA is realized in a 2.5-nm CFA film with B2-ordered structure observed by a high resolution transmission electron microscope.It is demonstrated that a high quality interface between the ferromagnetic layer and oxide layer is not essential for PMA.The conversions between in-plane anisotropy and PMA are investigated to study the dependence of magnetic moment on temperature.At the intersection points,the decreasing slope of the saturation magnetization（M s） changes because of the conversions.The dependence of M s on the annealing temperature and MgO thickness is also studied.     

垂直各向异性Ho3Fe5O12薄膜的外延生长与其异质结构的自旋输运

垂直磁各向异性稀土-铁-石榴石纳米薄膜在自旋电子学中具有重要应用前景.本文使用溅射方法在(111)取向掺杂钇钪的钆镓石榴石(Gd_0.63Y_2.37Sc₂Ga₃O₁₂,GYSGG)单晶衬底上外延生长了2—100 nm厚的钬铁石榴石(Ho₃Fe₅O₁₂,HoIG)薄膜,并进一步在HoIG上沉积了3 nm Pt薄膜.测量了室温下HoIG的磁各向异性和HoIG/Pt异质结构的自旋相关输运性质.结果显示,厚度薄至2 nm的HoIG薄膜(小于2个单胞层)在室温仍具有铁磁性,且由于外延应变,2—60 nm厚HoIG薄膜都具有很强的垂直磁各向异性,有效垂直各向异性场最大达350 mT;异质结构样品表现出非常可观的反常霍尔效应和“自旋霍尔/各向异性”磁电阻效应,前者在HoIG厚度小于4 nm时开始缓慢下降,而后者当HoIG厚度小于7 nm时急剧减小,说明相较于反常霍尔效应,磁电阻效应对HoIG的体磁性相对更加敏感;此外,自旋相关热电压随HoIG厚度减薄在整个厚度范围以指数方式下降,说明遵从热激化磁振子运动规律的自旋塞贝克效应是其主要贡献者.本文结果表明HoIG纳米薄膜具有可调控的垂直磁各向异性,厚度大于4 nm的HoIG/Pt异质结构具有高效的自旋界面交换作用,是自旋电子学应用发展的一个重要候选材料.     

Perpendicular magnetization and exchange bias in epitaxial NiO/[Ni/Pt]2 multilayers

The realization of perpendicular magnetization and perpendicular exchange bias(PEB)in magnetic multilayers is important for the spintronic applications.NiO(t)/[Ni(4 nm)/Pt(1 nm)]₂multilayers with varying the NiO layer thickness t have been epitaxially deposited on SrTiO;(001)substrates.Perpendicular magnetization can be achieved when t<25 nm.Perpendicular magnetization originates from strong perpendicular magnetic anisotropy(PMA),mainly resulting from interfacial strain induced by the lattice mismatch between the Ni and Pt layers.The PMA energy constant decreases monotonically with increasing t,due to the weakening of Ni(001)orientation and a little degradation of the Ni–Pt interface.Furthermore,significant PEB can be observed though NiO layer has spin compensated(001)crystalline plane.The PEB field increases monotonically with increasing t,which is considered to result from the thickness dependent anisotropy of the NiO layer.     

Pt/GdFeCo/Pt多层膜的磁性和反常霍尔效应研究

亚铁磁材料因具有反铁磁排列的子晶格磁矩而表现出诸多丰富的物理性质,在磁信息存储和逻辑领域具有广阔的应用前景.本文采用磁控溅射方法在热氧化的硅基片上制备了Pt/GdFeCo(t)/Pt多层膜,系统研究了亚铁磁GdFeCo厚度对多层膜的表面形貌、结构、磁性以及反常霍尔效应(AHE)的影响.结构测试表明薄膜表面粗糙度较小,且GdFeCo层为非晶态;实验中利用GdFeCo层厚度可有效控制Gd元素含量,从而调控GdFeCo趋近反铁磁态特性的磁矩补偿点;通过重金属强自旋轨道耦合效应(SOC)和非晶态亚铁磁薄膜面内压应力,实现了良好垂直各向异性(PMA);进一步阐明了亚铁磁薄膜中磁性和反常霍尔效应的内在产生机制以及磁矩补偿点与温度的内在关系.这些结果为构建新一代低功耗自旋电子器件奠定基础.     

Regulating the magnetic anisotropy by Hf thickness and heat treatment in Pt/Co/Hf films

Pt/Co/Hf multilayers were prepared by magnetron sputtering, and the magnetic anisotropy was effectively regulated by Hf thickness and heat treatment in Pt/Co/Hf films. The interface microstructures were characterized. The influence of the interface microstructure on magnetic properties was studied. The results show that the magnetic anisotropy in Pt/Co/Hf films is closely related to the interface microstructure, which is influenced by Hf thickness and the heat treatment temperature. Microstructure analysis shows that after the Pt(3)/Co(1.5)/Hf(1) film is heat-treated, the CoO_x content increases, more CoPt(111) forms, the interface is smoother and sharper, and the roughness of the Co/Hf interface decreases. Several factors work together to cause the magnetic anisotropy of the sample to change from in-plane magnetic anisotropy (IMA)to perpendicular magnetic anisotropy (PMA).     

Direct observation of dendritic domain growth in perpendicular magnetic anisotropy CoFe/Pt multilayers

We present the experimental results on thermally activated magnetization reversal for [Co_0.9Fe_0.1(5.0 Å)/Pt(20 Å)]₄ multilayer. Direct domain observations show that magnetization reversal is initiated with rare nucleation and followed by dendritic growth of domain walls. Based on macroscopic magnetic parameters from experimental data, the dendritic domain growth mode is qualitatively interpreted by Monte Carlo simulations in terms of a simple uniaxial magnetic anisotropy model. Moreover, both time evolution of domain growth observation and magnetic relaxation measurements reveal that CoFe/Pt multilayer has a relatively large activation volume compared with Co/Pt multilayers.     

Thickness-dependent magnetic properties in Pt/[Co/Ni]n multilayers with perpendicular magnetic anisotropy

We systematically investigated the Ni and Co thickness-dependent perpendicular magnetic anisotropy (PMA) coefficient, magnetic domain structures, and magnetization dynamics of Pt(5 nm)/[Co($t_{\rm Co}$)/Ni($t_{\rm Ni}$)]$_{5}$/Pt(1 nm) multilayers by combining the four standard magnetic characterization techniques. The magnetic-related hysteresis loops obtained from the field-dependent magnetization $M$ and anomalous Hall resistivity (AHR) $\rho_{{xy}}$ showed that the two serial multilayers with $t_{\rm Co} = 0.2$ nm and 0.3 nm have the optimum PMA coefficient $K_{\rm U}$ as well as the highest coercivity $H_{\rm C}$ at the Ni thickness $t_{\rm Ni}= 0.6 $ nm. Additionally, the magnetic domain structures obtained by magneto-optic Kerr effect (MOKE) microscopy also significantly depend on the thickness and $K_{\rm U}$ of the films. Furthermore, the thickness-dependent linewidth of ferromagnetic resonance is inversely proportional to $K_{\rm U}$ and $H_{\rm C}$, indicating that inhomogeneous magnetic properties dominate the linewidth. However, the intrinsic Gilbert damping constant determined by a linear fitting of the frequency-dependent linewidth does not depend on the Ni thickness and $K_{\rm U}$. Our results could help promote the PMA [Co/Ni] multilayer applications in various spintronic and spin-orbitronic devices.     

Magnetic properties of Co films and Co/Pt multilayers deposited on PDMS nanostructures

The magnetic properties of magnetron sputtered Co films (with in-plane anisotropy) and Co/Pt multilayers (with perpendicular anisotropy) deposited on elastomeric poly-dimethylsiloxane (PDMS) films and nanostructured templates are presented. Apart from the etched nanosize features, maze-like submicron features develop after the sputter deposition as a result of film buckling due to thermal contraction of the underlying PDMS layer. The nanostructured templates can physically isolate the magnetic entities but magnetic correlations within the range of the buckling features remain. By using oblique deposition geometries in-plane anisotropy develops and it is transferred to the PDMS buckling patterns. In the case of Co/Pt multilayers deposition on PDMS nanostructured templates results in a loss of the perpendicular anisotropy, attributed to the acuteness of the PDMS nanostructures.     

Enhancement of L10 ordered FePt by Pt buffer layer

L₁₀-ordered FePt thin films prepared by molecular-beam epitaxy on MgO (0 0 1) substrate at 320 °C with different thickness of Pt buffer layer have been investigated. The out-of-plane coercivity increases with increasing thickness of Pt buffer. The maximum values of the long-range order parameter and uniaxial magnetic anisotropy energy are 0.72 and 1.78×10⁷ erg/cm³, respectively, for films with 12 nm thick Pt buffer layer, where the c/a ratio (0.976) shows the minimum value. The reason for the enhancement in ordering is due to the proper lattice strains Pt buffer bestows on FePt layer, these strains are equal to the contraction in lattice parameter c and the expansion in a. Studies of angular-dependent coercivity revealed that the magnetization reversal behaviour shifts from a domain-wall motion dominated case towards a near rotational mode with increasing thickness of Pt buffer layer.     

Magnetization reversal and domains structures in (Co/Ni/Co/Pt) multilayers

Multilayers of [Co/Ni(t_Ni)/Co/Pt]_×4 are investigated for different Ni insertion layer thicknesses. The resulting magnetic properties and magnetic domain structures are compared with [Co/Ni]_×8 multilayers. As determined by magneto-optical Kerr effect microscopy and a vibrating sample magnetometer measurements, all multilayers exhibited a perpendicular magnetic anisotropy. It is found that the nucleation field and magnetic coercivity of [Co/Ni(t)/Co/Pt]_×4 multilayers are lower than (Co/Ni)_×8 and decreased with Ni thickness. Magnetization decay measurements reveal that these multilayers did not show an exponential decay behavior as was observed in rare earth transition metal alloys. Very narrow wires will remain stables for several hours even with an applied magnetic field closer to the coercivity. Insertion of very thin Ni in (Co/Pt) multilayers offers a good way to optimize the magnetic properties of the material and adjust the domain size for nanowire-based devices.     

MgO/Pt界面对增强Co/Ni多层膜垂直磁各向异性及热稳定性的研究

采用直流磁控溅射法在玻璃基片上制备了Pt底层和MgO/Pt双底层的Co/Ni多层膜样品, 通过反常霍尔效应研究了不同MgO厚度和退火温度对样品垂直磁各向异性(perpendicular magnetic anisotropy, PMA)的影响. 随着底层中MgO厚度的逐渐增加, 样品的矫顽力也随之增强, 霍尔电阻变化不大; 对样品进行退火处理后发现, 单纯Pt底层的Co/Ni多层膜随着退火温度的升高, 霍尔电阻逐渐降低, 矫顽力则迅速降低, 热稳定性较差; 而当MgO/Pt双底层的样品在200 ℃退火后矫顽力大幅增加, 霍尔电阻略微有所减小, 更高的退火温度使得Co和Ni合金化, 导致多层膜的PMA特征减弱.