Magnetization behavior of nanomagnets for patterned media application

Bit patterned media (BPM) which utilize each magnetic nanostructured dot as one recorded bit has attracted much interest as a promising candidate for future high-density magnetic recording. In this study, the magnetization reversal behaviors of nanostructured L1₀-FePt, Co/Pt multilayer (ML), and CoPt/Ru dots are investigated. For Co/Pt and CoPt/Ru nanodots, the bi-stable state is maintained in a very wide size range up to several hundred nm, and the magnetization reversal is dominated by the nucleation of a small reversed nucleus with the dimension of domain wall width. On the other hand, the critical size for the bi-stability of L1₀-FePt is about 60 nm, and its magnetization reversal proceeds via domain wall displacement even for such a small dot size. These reversal behaviors, depending on the magnetic materials, might be attributed to the difference in structural inhomogeneity, such as defects. In addition to the magnetic properties, the structural uniformity of the material could be crucial for the BPM application.     

Investigation of ferromagnetic coupling between Co layers in a Co/Pt multilayer with perpendicular anisotropy

The coercivity of a Co/Pt multilayer with out-of-plane anisotropy can be lowered greatly if it is grown onto an ultrathin NiO underlayer . By making use of this characteristic, a series of samples glass/NiO(10 Å)/[Co(4 Å)/Pt(5 Å)]₃/Pt(x Å)/[Co(4 Å)/Pt(5 Å)]₃ with different Pt spacer thickness have been prepared to determine the ferromagnetic (FM) coupling between Co layers across the Pt layer. The measurements of major and minor hysteresis loops have shown that the FM coupling between the top and bottom Co/Pt multilayers decreases monotonically with the Pt layer thickness and disappears above the Pt layer thickness of 40 Å. This thickness of 40 Å is much larger than that in the literature. In addition to the FM coupling between the top and bottom Co/Pt multilayers across the Pt spacer, there exists a weak biquadratic coupling, which induces the broad transition of the bottom Co/Pt multilayer.     

Magnetic reversal mechanism in strong perpendicular magnetic anisotropic CoPt/AlN multilayer film

Magnetic reversal mechanism of the Sub/AlN5 nm/[CoPt2 nm/AlN5 nm]₅ nano multilayer film, which shows strong perpendicular magnetic anisotropy (K_u=6.7×10⁶ erg/cm³), has been studied. The angle-dependent magnetic hysteresis loops of this highly perpendicular anisotropic CoPt/AlN multilayer film were measured in the present work, applying a magnetic field along different angles φ with respect to the film normal. It demonstrates that the magnetic reversal of the CoPt ultrathin layers in the CoPt/AlN multilayer film is occurred by the reversible magnetization rotation and the irreversible displacement of domain walls. The φ-dependent part of coercive field is resulted from the internal stress according to the Kondorsky and Kersten model. The φ-independent part of coercive field implies some random and isotropy pinning centers (e.g., vacancies, dislocations, grain boundaries) in the ultrathin CoPt layers. Our work is useful for coercivity control of metal/ceramics layered structures, in particular the perpendicular magnetic tunneling junctions.     

Magnetization reversal dynamics in Au/Co/Au(111) ultrathin films: Effect of roughness of the buffer layer

We present a study of the magnetization reversal dynamics in ultrathin Au/Co/Au films with perpendicular magnetic anisotropy, for a Co thickness of 0.5, 0.7 and 1 nm. In these films, the magnetization reversal is dominated by domain nucleation for t_Co=0.5, 0.7 nm and by domain wall propagation for t_Co=1 nm. The prevalence of domain nucleation for the thickness range 0.5-0.7 nm is different from results reported in the literature, for the same system and for the same thickness range, where the magnetization reversal took place mainly by domain wall motion. We attribute this difference to the effect of roughness of the Au buffer layer on the morphology of the magnetic layer.     

Perpendicular magnetic anisotropy and magnetic proximity effect in Pt1−δFeδ/Co multilayer films

The perpendicular magnetic anisotropy (PMA) and magnetization in Pt_1−δFe_δ/Co (δ=0, 0.017, 0.04 and 0.06) multilayer films have been investigated. It is found that, on adding a small amount of Fe into the Pt layers, Pt/Co multilayer films maintain well-defined PMA at both 5 and 300 K along with significantly enhanced magnetization even at room temperature, which is far greater than the Curie temperature of Pt_1−δFe_δ dilute alloys. Further study demonstrates that the large enhancement of the magnetization in the Fe doped Pt/Co multilayers at 300 K arises from the bulk moment of the Pt_1−δFe_δ layers at the interface region, where the ferromagnetic order persists up to room temperature due to the strengthened exchange interactions between Fe atoms via strongly polarized Pt near the Pt_1−δFe_δ/Co interfaces. For the Pt_0.96Fe_0.04/Pt multilayers, the magnetically ordered region in each Pt_0.96Fe_0.04 layer extends over at least 10 Å from the interface at room temperature.     

Magnetization reversal in perpendicular exchange-biased multilayers

Co/Pt multilayers with perpendicular magnetic anisotropy exhibit an exchange bias when covered with an IrMn layer. The exchange bias field, which is about 7 mT for 3 Co/Pt bilayer repetitions and a Co layer thickness of 5 Å, can be increased up to 16.5 mT by the insertion of a thin Pt layer at the Co/IrMn interface. The interfacial magnetic anisotropy of the Co/IrMn interface (KSCo/IrMn =-0.09 mJ/m2) favours in-plane magnetization and tends to tilt the Co spins away from the film normal. Dynamical measurements of the magnetization reversal process reveal that both thermally activated spin reversal in the IrMn layer and domain wall nucleation in the Co/Pt multilayer influence the interfacial spin structure and therefore the strength of the perpendicular exchange bias field.     

Influence of Pt thickness on magnetization reversal processes in (Pt/Co)3 multilayers with perpendicular anisotropy

We present a detailed study of the magnetization reversal in perpendicularly magnetized (Pt/Co)₃ multilayers with different values of the platinum interlayer thickness t_Pt. To study the magnetization reversal in our samples we combined measurements of relaxation curves with the direct visualization of domain structures. Magnetization reversal was dominated by domain wall propagation for t_Pt=1 nm and by domain nucleation for t_Pt=0.2 nm, while a mixed process was observed for t_Pt=0.8 nm. We interpret our results within the framework of a model of thermally activated reversal where a distribution of activation energy barriers is taken into account. The reversal process was correlated with the energy barrier distribution.     

Structural and magnetic study of swift heavy ion irradiated W/Fe multilayer structure

The present study reports the effect of swift heavy ion irradiation on structural and magnetic properties of sputtered W/Fe multilayer structure (MLS) having bilayer compositions of [W(10 Å)/Fe(20 Å)]_10BL. The MLS is irradiated by 120 MeV Au⁹⁺ ions of fluences 1×10¹³ and 4×10¹³ ions/cm². Techniques like X-ray reflectivity (XRR), cross-sectional transmission electron microscopy (X-TEM) and DC magnetization with a vibrating sample magnetometer (VSM) are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt’s formalism shows a significant increase in W/Fe layer roughness. X-TEM studies reveal that intra-layer microstructure of Fe layers in MLS becomes nano-crystalline on irradiation. DC magnetization study shows that with spacer layer thickness interlayer coupling changes between ferromagnetic to antiferromagnetic.     

Structural and magnetic properties of Pt in Co/Pt multilayers

[Co(30 Å)/Pt(x Å)]₂₀ multilayers with the Pt layer thicknesses varying from 5 Å to 20 Å were characterized structurally by high angle X-ray diffraction, X-ray reflectivity, X-ray absorption spectroscopy and magnetically by X-ray magnetic circular dichroism. It is found that the structure and magnetic properties of Pt have a strong correlation with the Pt layer thickness. The 20 Å thickness Pt layer is not almost influenced by the adjacent Co layer and the nearest neighbors are dominated by Pt-Pt shells. With decreasing Pt layer thickness, the nearest neighbors are gradually dominated by Pt-Co shells and the Pt-Co intermixing regions also remarkable increase at the interfaces, especially for the 5 Å thickness Pt layer. The orbital and spin magnetic moments as well as the ratio m_orb/m_spin all decrease systematically with increasing Pt layer thickness, indicating that the interface atoms are polarized by direct Pt-Co hybridization, but that the adjacent layers are polarized by Pt-Pt interactions.     

Magnetic field dependence of asymmetry in the magnetization reversal of ultrathin Co films and Co/Pt multilayers with perpendicular anisotropy

We studied the magnetization reversal in ultrathin [Co/Pt]_n films (n=1, 2, and 4) using magneto-optical Kerr microscopy. These materials demonstrate unusual asymmetries in the activity of nucleation centers and domain wall motion. It was found that application of very high holding magnetic field prior to magnetization reversal, exceeding some critical value much larger than the apparent saturation field, suppresses the subsequent ‘asymmetric’ nucleation centers, activity. We revealed that the ‘asymmetric’ nucleation centers become active again after subsequent reversal cycles coming from a smaller holding field and studied how the asymmetry returns with the decrease of applied holding field. It was found that in low-coercivity ultrathin Co films, the asymmetry in domain wall velocity decreased sharply with the applied field increase and disappeared when the reversal field is greater than μ₀H=1.5 mT.     

Magnetization reversal in [Ni/Pt]6/Pt(x)/[Co/Pt]6 multilayers

The magnetization reversal is studied in magnetron sputtered artificial superstructures of the form [Ni/Pt]₆/Pt(x)/[Co/Pt]₆ with perpendicular anisotropy, in which the [Co/Pt]₆ stacks have higher coercivity than the [Ni/Pt]₆. For x≥2 nm the two stacks reverse separately and exhibit characteristic stepped loops with a “plateau” in the region between the two switching fields. First-Order Reversal Curves (FORCs) reveal that the maximum coupling is obtained for x=1.5 nm. While each of the Ni/Pt and Co/Pt stacks by itself is thin enough to reverse in large domains when they are coupled, formation of maze like domains is observed. In this case some reversibility of the demagnetization curves associated with interfacial domain wall pinning appears while in the rest of the cases the reversal mechanism is based on lateral domain wall pinning with low reversibility. In the loops monitored by Extraordinary Hall Effect (EHE) measurements this “plateau” appears as a hump due to the different sign of the EHE coefficient between the [Ni/Pt]₆ and [Co/Pt]₆.     

Influence of heat treatment on the structure and magnetic properties of the Co/Zr and Co/Hf multilayer amorphous films

The influence of annealing on the structure and magnetic properties of amorphous Co/Zr and Co/Hf multilayer films was studied with particular attention to the dependence of the magnetic properties, thermal stability and crystallization process on layer composition and thickness. The temperature at which crystallization commences increases from 400 to 460 °C as the layer thickness d_Zr or d_Hf increases from 6 to 18 Å, and decreases from 450 to 400 °C as d_Co increases from 12 to 18 Å. Multilayers containing 19–60 at% Zr were studied. The specific magnetization was found to increase even below the temperature at which crystallization commences. Our data are compared with non-multilayer Co–Zr amorphous films and rapidly quenched metallic glasses.     

Enhancement of L10 ordered FePt by Pt buffer layer

L₁₀-ordered FePt thin films prepared by molecular-beam epitaxy on MgO (0 0 1) substrate at 320 °C with different thickness of Pt buffer layer have been investigated. The out-of-plane coercivity increases with increasing thickness of Pt buffer. The maximum values of the long-range order parameter and uniaxial magnetic anisotropy energy are 0.72 and 1.78×10⁷ erg/cm³, respectively, for films with 12 nm thick Pt buffer layer, where the c/a ratio (0.976) shows the minimum value. The reason for the enhancement in ordering is due to the proper lattice strains Pt buffer bestows on FePt layer, these strains are equal to the contraction in lattice parameter c and the expansion in a. Studies of angular-dependent coercivity revealed that the magnetization reversal behaviour shifts from a domain-wall motion dominated case towards a near rotational mode with increasing thickness of Pt buffer layer.     

Influence of multilayer modulation on structural and magnetic features in the Pt/Sm-Co system

In this work, we study the influence of Pt underlayer in Pt/Sm-Co/Pt trilayers and in Pt/Sm-Co multilayers. In both cases, Pt underlayer seems to impose better crystallinity to Sm-Co layer and certainly promotes the evolution of the hard-magnetic SmCo₅ phase. Particularly, in the case of multilayer form, where multiple interlayers of Pt each one serving as a dedicated underlayer for the deposition of a specific Sm-Co layer, enhanced crystallinity is observed. Moreover, post-deposition annealing facilitates these features at relatively lower temperatures (∼400 °C) than those met in thin-film cases. This behavior is also followed by enhancement of saturation magnetization, while higher temperature post-deposition thermal treatment seems to deteriorate structural and magnetic features. If annealing temperature gets over 550 °C macroscopic magnetic features depress, probably due to domination of annealing-activated processes such as Sm oxidation and formation of non-magnetic phases since Pt diffuses throughout the whole magnetic layer.     

Study of domain structure and magnetization reversal after thermal treatments in Fe40Co38Mo4B18 microwires

We have studied the effect of thermal treatment on the magnetic domain structure and magnetic reversal process of amorphous and nanocrystalline Fe₄₀Co₃₈Mo₄B₁₈ microwires. The domain structure and the magnetization reversal of amorphous FeCoMoB microwires reflect the complex stress distribution introduced by the glass coating. Hence, the thickness of radial domain structure decreases with temperature and the temperature dependence of the switching field presents a discontinuous behavior. After nanocrystallization, the domain structure of FeCoMoB microwire is almost constant within the temperature range 10-400 K and the switching field decreases almost linearly with temperature mostly because of the decrease of saturation magnetization.     

Magnetic layer thickness dependence of magnetization reversal in electrodeposited CoNi/Cu multilayer nanowires

The magnetization reversal of electrodeposited CoNi/Cu multilayer nanowires patterned in an array using a hole template has been investigated. The reversal mode is found to depend on the CoNi layer thickness t(CoNi); with increasing t(CoNi) a transition occurs from coherent rotation to a combination of coherent and incoherent rotation at around t(CoNi)=51 nm. The reversal mode has been identified using the magnetic hysteresis loops measured at room temperature for CoNi/Cu nanowires placed at various angles between the directions of the nanowire axis and external fields using a vibrating sample magnetometer. The nanowire samples have a diameter of ∼250 nm and constant Cu layer thickness of 4.2 nm with various t(CoNi) ranging from 6.8 nm to 7.5 μm. With increasing t(CoNi), the magnetic easy axis moves from the direction perpendicular to nanowires to that parallel to the nanowires at around t(CoNi)=51 nm, indicating a change in the magnetization reversal mode. The reversal mode for the nanowires with thin disk-shaped CoNi layers (t(CoNi)=6.8, 12 and 17 nm) is of a coherent rotation type, while that for long rod-shaped CoNi layers (t(CoNi)=150 nm, 1.0, 2.5 and 7.5 μm) can be consistently explained by a combination of coherent rotation and a curling mode. The effects of dipole–dipole interactions between nanowires and between adjacent magnetic layers in each nanowire on the reversal process have been discussed.     

Ordering temperature of L10-type FePt films reduced by CuO addition

Effects of addition of CuO layers in L1₀-type FePt thin films are investigated. The ordering temperature of L1₀-type FePt films can be reduced by CuO addition. The coercivities of 0.78 and 0.82 T are achieved in [Pt(10 Å)/Fe(14 Å)/CuO(2 Å)]₁₀ film annealed at 550 °C for 20 min and [Pt(10 Å)/Fe(15 Å)/CuO(3 Å)]₁₀ film annealed at 600 °C for 20 min, respectively, and these values are compared to the coercivity of 0.8 T in [Pt(10 Å)/Fe(13 Å)]₁₀ film annealed at 650 °C. The thickness of Fe and CuO layers strongly influences the ordering temperature of L1₀-type FePt and the magnetic properties of the films. The addition of CuO not only brings microstructure and surface morphology changes of FePt film, but also lowers the ordering temperature.     

High-frequency properties of discontinuous FeCoSi/native-oxide multilayer films

Discontinuous [FeCoSi (d)/native-oxide]₅₀ multilayer films were fabricated by DC magnetron sputtering without any post-deposition treatment. The films exhibit good soft magnetic properties with initial permeability μ_i larger than 100, the saturation magnetization 4πM_s and the in-plane uniaxial anisotropy field H_k increase as the magnetic FeCoSi layer thickness d is increased from 5.5 to 20.5 Å. As a consequence, the ferromagnetic resonance frequencies f_r of the films increase from 2.0 to 3.9 GHz. The combination of high f_r and large μ_i makes these films potential candidates for magnetic devices applied in the high-frequency range. The origin of the excellent high-frequency properties in discontinuous FeCoSi/native-oxide multilayer films is discussed.     

Improvement of magnetic properties and read/write characteristics in SmCo5 perpendicular thin films

An SmCo₅ alloy is a promising candidate for ultra-high density magnetic recording media because of its strong uniaxial magnetocrystalline anisotropy, whose constant, K_u, is more than 1.1×10⁸ erg/cm³. Recently, we successfully obtained high perpendicular magnetic anisotropy for a sputter-deposited SmCo₅ thin film by introducing a Cu/Ti dual underlayer. However, it is necessary to improve magnetic properties and read/write (R/W) characteristics for applying SmCo₅ thin films to perpendicular magnetic recording media. In this study, we focused on reduction of magnetic domain size and change of a magnetization reversal process of SmCo₅ perpendicular magnetic thin films by introducing carbon (C) atoms into the constituent Cu underlayer. The magnetic domain size became small and the ratio of coercivity (H_c) against magnetic anisotropy (H_k) which is an index of the magnetization reversal process was increased by adding C atoms. We also evaluated the R/W characteristics of SmCo₅ double-layered media including C atoms. The medium noise was decreased and signal-to-noise ratio increased by introducing the C. The addition of C into the Cu underlayer is effective for changing the magnetization reversal process, reducing medium noise and increasing SNR.     

Perpendicular anisotropy of Co3Pt deposited on the NiFeMo/Ru buffer

The multilayer of Ta/NiFeMo/Ru/Co₃Pt was sputter deposited on the Si (1 0 0) wafer. Using the NiFeMo buffer layer greatly enhanced the texture of Co₃Pt layer. The enhanced texture increased the perpendicular magnetic anisotropy of Co₃Pt. According to the VSM and XRD results, only the 5 nm of NiFeMo was good enough to produce the texture and perpendicular anisotropy in Co₃Pt layer. The perpendicular anisotropy was attributed to the existence of short-range-ordered HCP structure of Co₃Pt.