利用FePt/Au多层膜结构制备垂直磁记录L10-FePt薄膜

利用磁控溅射方法在100℃的MgO单晶基片上制备了［FePt/Au］₁₀多层膜,并研究了采用FePt/Au多层膜结构对FePt薄膜的有序化温度、矫顽力（H_C）、垂直磁各向异性、晶粒尺寸以及颗粒间磁交换耦合作用的影响.磁性测试结果表明：FePt/Au多层膜在退火后具有较高的H_C、良好的垂直磁各向异性、较小的晶粒尺寸且无磁交换耦合作用.截面高分辨电镜分析表明：Au可以缓解MgO和FePt之间较大的晶格错配,从而促进薄 关键词： 0-FePt薄膜')" href="#">L1₀-FePt薄膜 有序化温度 垂直磁各向异性 磁交换耦合作用     

具有垂直各向异性(Pt/Co)n/FeMn多层膜的交换偏置

采用磁控溅射方法制备了以Pt为缓冲层和保护层的具有垂直各向异性(Pt/Co)_n/ FeMn多层膜.研究结果表明，多层膜的垂直交换偏置场H_ex和反铁磁层厚度的关 系与其具有平面各向异性的交换偏置场随反铁磁层厚度变化趋势相近.随着铁磁层调制周期 数的增加，垂直交换偏置场H_ex相应减小，并且与铁磁层的调制周期数近似成反 比关系.(Pt/Co)₃/FeMn的垂直交换偏置场H_ex已经达到22.3kA/m.为 关键词： 交换偏置 垂直各向异性 多层膜     

真空退火对周期性界面掺杂Ni80Co20薄膜磁性的影响

用磁控溅射方法制备了两个具有不同Fe层厚度的［Ni₈₀Co₂₀(L)/Fe(t_Fe)］_N多层膜系列样品,其中t_Fe=0.1和2nm.研究了两个系列样品的磁及输运性质随Ni₈₀Co₂₀层厚度L的变化关系.在退火态［Ni₈₀Co₂₀(L)/Fe(0.1nm)］_N系列样品中,发现各向异性磁电阻( 关键词： 多层膜 各向异性磁电阻 界面效应 退火     

Co/Ni多层膜垂直磁各向异性的研究

采用直流磁控溅射法在玻璃基片上制备了Pt底层的Co/Ni多层膜样品, 对影响样品垂直磁各向异性的各因素进行了调制, 通过样品的反常霍尔效应系统的研究了Co/Ni多层膜的垂直磁各向异性. 结果表明, 多层膜中各层的厚度及周期数对样品的反常霍尔效应和磁性有重要的影响. 通过对多层膜各个参数的调制优化, 最终获得了具有良好的垂直磁各向异性的Co/Ni多层膜最佳样品Pt(2.0)/Co(0.2)/Ni(0.4)/Co(0.2)/Pt(2.0), 经计算, 该样品的各向异性常数K_eff 达到了3.6×10⁵ J/m³, 说明样品具备良好的垂直磁各向异性. 最佳样品磁性层厚度仅为0.8 nm, 样品总厚度在5 nm以内, 可更为深入的研究其与元件的集成性.     

Er2(Fe1-xCox)15Ga2化合物的磁晶各向异性

通过X射线衍射和磁性测量等手段研究了Er₂(Fe_1-xCo_x)₁₅Ga₂化合物的结构与磁性，重点讨论了它们的磁晶各向异性.实验结果表明，Er₂(Fe_1-xCo_x)₁₅Ga₂化合物均为Th₂Ni₁₇型六角结构，晶格常数a,c和单胞体积V随Co含量的 关键词：     

Pt插层对Co/FeMn界面的影响

采用磁控溅射的方法制备了Co/FeMn/Co多层膜,研究了Co（底部）/FeMn和FeMn/Co（顶部）界面插入Pt层后磁矩的变化情况．通过测量磁滞回线可知,Co（底部）/FeMn界面的Pt插层改变了体系的饱和磁化强度Ｍ_s,随着Co层厚度（t_Co）的增加Ｍ_s不断趋近于Co块体结构理论值1440 kA/m．这是因为Co（底部）/FeMn界面产生了净磁矩,而界面处的Pt插层可以减少这种净磁矩的产生．但是 关键词： 磁性多层膜 垂直磁各向异性 交换耦合     

垂直取向FePt/Ag纳米颗粒薄膜的结构和磁性

用磁控溅射法在单晶MgO(100)基片上制备了［FePt 2 nm/Ag dnm］₁₀多层膜， 经真空热处理后，得到具有高矫顽力的垂直取向L1₀-FePt/Ag颗粒膜.x射线衍射结 果表明，在250 ℃的热基片上溅射，当Ag层厚度d=3—11 nm时，FePt颗粒具有很好的［001］取向，随着Ag层厚度的增加，FePt颗粒尺寸减小.［FePt 2 nm/Ag 9 nm］₁₀经过6 00 ℃真空热处理15 min后，颗粒大小仅约8 nm，垂直矫顽力达到692 kA/m.这种无磁耦合作用的颗粒膜，适合用作超高密度的垂直磁记录介质. 关键词： 磁控溅射 垂直磁记录 纳米颗粒膜 0-FePt/Ag')" href="#">L1₀-FePt/Ag     

CoFeB/AlOx/Ta及AlOx/CoFeB/Ta结构中垂直易磁化效应的研究

本文详细研究了在不同氧化层和铁磁层厚度情况下, 底层CoFeB/AlO_x/Ta结构和 顶层AlO_x/CoFeB/Ta结构中的垂直磁各向异性. 在底层CoFeB/AlO_x/Ta结构中观察到了垂直磁化的磁滞回线, 证明了其垂直易磁化效应的存在; 而在顶层AlO_x/CoFeB/Ta结构中却没有观察到类似的磁滞回线. 对这种对称结构中的非对称现象进行了分析. 研究还发现不同的氧化层和铁磁层厚度均会影响层间界面相互作用的强度, 从而导致结构的垂直磁化曲线矫顽力大小发生改变. 这项研究将对基于AlO_x氧化层垂直磁隧道结的研制具有重要的意义. 关键词： 垂直磁各向异性 磁隧道结 随机存储器     

垂直各向异性Ho3Fe5O12薄膜的外延生长与其异质结构的自旋输运

垂直磁各向异性稀土-铁-石榴石纳米薄膜在自旋电子学中具有重要应用前景.本文使用溅射方法在(111)取向掺杂钇钪的钆镓石榴石(Gd_0.63Y_2.37Sc₂Ga₃O₁₂,GYSGG)单晶衬底上外延生长了2—100 nm厚的钬铁石榴石(Ho₃Fe₅O₁₂,HoIG)薄膜,并进一步在HoIG上沉积了3 nm Pt薄膜.测量了室温下HoIG的磁各向异性和HoIG/Pt异质结构的自旋相关输运性质.结果显示,厚度薄至2 nm的HoIG薄膜(小于2个单胞层)在室温仍具有铁磁性,且由于外延应变,2—60 nm厚HoIG薄膜都具有很强的垂直磁各向异性,有效垂直各向异性场最大达350 mT;异质结构样品表现出非常可观的反常霍尔效应和“自旋霍尔/各向异性”磁电阻效应,前者在HoIG厚度小于4 nm时开始缓慢下降,而后者当HoIG厚度小于7 nm时急剧减小,说明相较于反常霍尔效应,磁电阻效应对HoIG的体磁性相对更加敏感;此外,自旋相关热电压随HoIG厚度减薄在整个厚度范围以指数方式下降,说明遵从热激化磁振子运动规律的自旋塞贝克效应是其主要贡献者.本文结果表明HoIG纳米薄膜具有可调控的垂直磁各向异性,厚度大于4 nm的HoIG/Pt异质结构具有高效的自旋界面交换作用,是自旋电子学应用发展的一个重要候选材料.     

(Nd1－xGdx)3Fe27.31Ti1.69化合物的结构和磁性

通过X射线衍射和磁性测量等手段研究了(Nd_1-xGd_x)₃Fe_27.31Ti_1.69(0≤x≤0.6)化合物的结构和磁性.X射线衍射测量结果表明Gd替代后并未改变Nd₃(Fe,Ti)₂₉化合物的晶体结构，但引起了晶胞体积收缩.随着Gd含量的增加，化合物的居里温度T_C和室温磁晶各向异性场B_a单调增加，而自旋重取向 关键词： 1-xGd_x)₃Fe_27.31Ti_1.69化合物')" href="#">(Nd_1-xGd_x)₃Fe_27.31Ti_1.69化合物 磁晶各向异性 自旋重取向 磁相图     

Thickness-dependent magnetic properties in Pt/[Co/Ni]n multilayers with perpendicular magnetic anisotropy

We systematically investigated the Ni and Co thickness-dependent perpendicular magnetic anisotropy (PMA) coefficient, magnetic domain structures, and magnetization dynamics of Pt(5 nm)/[Co($t_{\rm Co}$)/Ni($t_{\rm Ni}$)]$_{5}$/Pt(1 nm) multilayers by combining the four standard magnetic characterization techniques. The magnetic-related hysteresis loops obtained from the field-dependent magnetization $M$ and anomalous Hall resistivity (AHR) $\rho_{{xy}}$ showed that the two serial multilayers with $t_{\rm Co} = 0.2$ nm and 0.3 nm have the optimum PMA coefficient $K_{\rm U}$ as well as the highest coercivity $H_{\rm C}$ at the Ni thickness $t_{\rm Ni}= 0.6 $ nm. Additionally, the magnetic domain structures obtained by magneto-optic Kerr effect (MOKE) microscopy also significantly depend on the thickness and $K_{\rm U}$ of the films. Furthermore, the thickness-dependent linewidth of ferromagnetic resonance is inversely proportional to $K_{\rm U}$ and $H_{\rm C}$, indicating that inhomogeneous magnetic properties dominate the linewidth. However, the intrinsic Gilbert damping constant determined by a linear fitting of the frequency-dependent linewidth does not depend on the Ni thickness and $K_{\rm U}$. Our results could help promote the PMA [Co/Ni] multilayer applications in various spintronic and spin-orbitronic devices.     

MgO/Pt界面对增强Co/Ni多层膜垂直磁各向异性及热稳定性的研究

采用直流磁控溅射法在玻璃基片上制备了Pt底层和MgO/Pt双底层的Co/Ni多层膜样品, 通过反常霍尔效应研究了不同MgO厚度和退火温度对样品垂直磁各向异性(perpendicular magnetic anisotropy, PMA)的影响. 随着底层中MgO厚度的逐渐增加, 样品的矫顽力也随之增强, 霍尔电阻变化不大; 对样品进行退火处理后发现, 单纯Pt底层的Co/Ni多层膜随着退火温度的升高, 霍尔电阻逐渐降低, 矫顽力则迅速降低, 热稳定性较差; 而当MgO/Pt双底层的样品在200 ℃退火后矫顽力大幅增加, 霍尔电阻略微有所减小, 更高的退火温度使得Co和Ni合金化, 导致多层膜的PMA特征减弱.     

Regulating the magnetic anisotropy by Hf thickness and heat treatment in Pt/Co/Hf films

Pt/Co/Hf multilayers were prepared by magnetron sputtering, and the magnetic anisotropy was effectively regulated by Hf thickness and heat treatment in Pt/Co/Hf films. The interface microstructures were characterized. The influence of the interface microstructure on magnetic properties was studied. The results show that the magnetic anisotropy in Pt/Co/Hf films is closely related to the interface microstructure, which is influenced by Hf thickness and the heat treatment temperature. Microstructure analysis shows that after the Pt(3)/Co(1.5)/Hf(1) film is heat-treated, the CoO_x content increases, more CoPt(111) forms, the interface is smoother and sharper, and the roughness of the Co/Hf interface decreases. Several factors work together to cause the magnetic anisotropy of the sample to change from in-plane magnetic anisotropy (IMA)to perpendicular magnetic anisotropy (PMA).     

CoFeB/Pt多层膜的垂直磁各向异性研究

具有垂直磁各向异性的磁性纳米结构是自旋转移力矩器件的重要研究内容, 本文采用反常霍尔效应系统地研究了磁控溅射法制备的[CoFeB/Pt]_n多层膜的垂直磁各向异性. 当CoFeB的厚度小于0.6 nm时, 可以在[CoFeB/Pt]_n多层膜中观察到清晰的垂直磁各向异性, 其垂直磁各向异性强烈依赖于CoFeB和Pt层厚度及多层膜周期数. 当多层膜周期数n ≥ 5时, 出现零剩磁现象. 另外, [CoFeB/Pt]_n多层膜的矫顽力均小于2 kA·m^-1, 有望作为垂直自由层的重要侯选材料应用于垂直磁纳米结构中.     

Ultrathin (CoFe/Pt)n multilayers with tuned magnetic properties

Perpendicular magnetic anisotropy (PMA) has been investigated in ultrathin (CoFe [0.2] nm/Pt [0.2] nm)_n multilayers. The Pt layers show an fcc crystal structure with a preferred [111] orientation. The multilayers with n=3, 4 show PMA in the as-grown state, which can be enhanced by thermal annealing. However, no PMA is observed in the as-grown state with higher repetitions (n>&=5), although it is observed after thermal annealing. For 1=&<n=&<8, the anisotropy energy is around 10⁵ J/m³ for all (CoFe [0.2]/Pt [0.2])_n stacks. The perpendicular anisotropy is related to layer thickness and interface roughness.     

Pt974Mn26/Co多层膜的磁性与磁光性质研究

用磁控溅射法制备了Mn含量一定、不同PtMn层厚度的Pt974Mn26/Co磁性多层膜系列，通过x射线衍射对该多层膜系列进行结构分析；测定了不同PtMn层厚度系列样品的磁滞回线、有效垂直各向异性，分析了饱和磁化强度和有效垂直各向异性变化的原因；通过测定该多层膜体系的克尔谱，分析了一定波长下克尔角随PtMn层厚度变化的规律.认为克尔角的变化是由于界面的合金化以及原子的极化减小所致. 关键词： 多层膜 磁性 磁光     

Magnetization reversal and domains structures in (Co/Ni/Co/Pt) multilayers

Multilayers of [Co/Ni(t_Ni)/Co/Pt]_×4 are investigated for different Ni insertion layer thicknesses. The resulting magnetic properties and magnetic domain structures are compared with [Co/Ni]_×8 multilayers. As determined by magneto-optical Kerr effect microscopy and a vibrating sample magnetometer measurements, all multilayers exhibited a perpendicular magnetic anisotropy. It is found that the nucleation field and magnetic coercivity of [Co/Ni(t)/Co/Pt]_×4 multilayers are lower than (Co/Ni)_×8 and decreased with Ni thickness. Magnetization decay measurements reveal that these multilayers did not show an exponential decay behavior as was observed in rare earth transition metal alloys. Very narrow wires will remain stables for several hours even with an applied magnetic field closer to the coercivity. Insertion of very thin Ni in (Co/Pt) multilayers offers a good way to optimize the magnetic properties of the material and adjust the domain size for nanowire-based devices.     

Magnetic properties of a Pt/Co₂ FeAl/MgO structure with perpendicular magnetic anisotropy

Microstructures and magnetic properties of Ta/Pt/Co 2 FeAl(CFA)/MgO multilayers are studied to understand perpendicular magnetic anisotropy(PMA) of half-metallic full-Heusler alloy films.PMA is realized in a 2.5-nm CFA film with B2-ordered structure observed by a high resolution transmission electron microscope.It is demonstrated that a high quality interface between the ferromagnetic layer and oxide layer is not essential for PMA.The conversions between in-plane anisotropy and PMA are investigated to study the dependence of magnetic moment on temperature.At the intersection points,the decreasing slope of the saturation magnetization(M s) changes because of the conversions.The dependence of M s on the annealing temperature and MgO thickness is also studied.