基于金属狭缝阵列的各向异性偏振分束器

在金属-电介质结构的基础上提出了一种基于金属狭缝阵列的各向异性偏振分束器,并采用有限元法研究了横磁(TM)和横电(TE)偏振光入射后结构所表现出的负反射和镜面反射等特性.计算结果表明,当偏振光的入射角设定在20?—70?时,入射的TM光发生强烈的负反射,而TE光的负反射很弱,并随着波长的增加而急剧下降.分析可得偏振分束光栅的理想负反射点和反射面的完美对称响应效果.通过仿真得到了理想负反射点的取值范围.结合严格耦合波法软件,计算不同偏振光入射时负反射和镜面反射条件下的反射率,其消光比高达10~6.     

任意偏振态光束全反射时的侧向和横向位移

光束在电介质界面发生全反射时,实际反射光束会在入射面内相对于几何反射光束产生一侧向位移,在垂直于入射面的方向产生一横向位移。利用改进的能流法研究了任意偏振态光束发生全反射时的侧向和横向位移特性。研究表明,侧向位移的大小与入射光束的两组成部分———TE和TM偏振光的相位差无关,而与两组分的光强比密切相关,且该位移可以表示为TE和TM偏振光束各自的位移按光强的加权平均。横向位移的大小不仅与入射光束两组分的光强比相关,还与组分的相位差密切相关。另外,反射光束不仅在椭圆偏振态入射的情况下会产生横向位移,而且在TE和TM偏振态之外的其他线偏振态入射时,也会产生横向位移。     

A polarization splitter based on slow light effect in a left-handed material waveguide

We propose a polarization splitter (PS) based on the slow light effect in a three-layer waveguide that consists of left-handed material (LHM) and dielectric layers with no birefringence. Transverse electric (TE) and transverse magnetic (TM) waves can be split by the intrinsic configuration of permittivity and permeability of LHM and dielectric layers. Simulation results are given to discuss the influence of electromagnetic parameters on the properties of our PS, and the capture and release of TE or TM waves are also realized in our PS which provides a flexible method to modulate the switching of different polarization waves.     

Tunable directional beaming assisted by asymmetrical SPP excitation in a subwavelength metallic double slit

We present a design for tunable directional beaming through a subwavelength metallic double slit surrounded by dielectric surface-relief gratings.On-axis and off-axis beaming can be switched by controlling the incident angle to asymmetrically excite surface plasmon polaritons(SPPs) that are subsequently coupled out to propagating beams by the two gratings on the left and the right sides of the double slit.Furthermore,the division of optical power into two off-axis beaming directions can be tuned smoothly by varying the incident angle while keeping the total power almost unchanged.The mechanism of this effect is analyzed theoretically and verified using rigorous numerical simulations.     

High extinction ratio metal-insulator-semiconductor waveguide surface plasmon polariton polarizer

The attenuation characteristics of a multilayer metal clad GaAs-AlGaAs optical waveguide polarizer are theoretically investigated. The dispersion relations and field distribution of the multilayer structures are calculated for different geometrical parameters and material properties. The polarizer studied consists of a single mode finite/infinite metal clad GaAs-AlGaAs waveguide with a dielectric (SiO₂/Si₃N₄) buffer layer inserted between the metal and the waveguide.Conventionally, the TM polarized waves are found to exhibit an absorption peak at a particular buffer thickness (called critical buffer thickness).We shall show that the maximum TM absorption can be improved by a multiple factor up to 7 by choosing a buffer layer thicker than its critical value. This corresponds to an extinction ratio of 1470 dB for a polarizer length of 1 mm. Further, thicker buffers reduce the insertion losses and values as low as 0.1 dB can be obtained. The strong TM absorption in these structures is interpreted as resonant coupling of the guided mode to the lossy surface plasmon polariton supported by the thin metal film. Thicker buffer also reduces the TE losses (insertion losses) and hence increases the extinction ratio (ratio of TM to TE losses).This can be achieved by optimizing the buffer and the metal thicknesses. Another equally efficient polarizer can be designed by positioning a dielectric (same as buffer) layer (superstrate layer) above the metal film and then optimizing the buffer, metal and the superstrate thicknesses. We also show that the proposed polarizer with the superstrate layer is highly stable even when exposed to the extreme atmospheric changes.     

Design of a compact polarization beam splitter based on a deformed photonic crystal directional coupler

In this paper a compact polarization beam splitter based on a deformed photonic crystal directional coupler is designed and simulated. The transverse-electric （TE） guided mode and transverse-magnetic （TM） guided mode are split due to different guiding mechanisms. The effect of the shape deformation of the air holes on the coupler is studied. It discovered that the coupling strength of the coupled waveguldes is strongly enhanced by introducing elliptical airholes, which reduce the device length to less than 18.Sttm. A finite-difference tlme-domain simulation is performed to evaluate the performance of the device, and the extinction ratios for both TE and TM polarized light are higher than 20 dB.     

Resistive high-impedance surfaces (RHIS) as absorbers for oblique incidence electromagnetic waves

This paper presents a lightweight microwave absorber suitable for space applications. The absorber is based on a resistive high-impedance surface (RHIS) optimized to achieve reflection under ?15 dB in the band (2–2.3 GHz) at oblique incidence for transverse electric (TE) and transverse magnetic (TM) polarizations. A first classical isotropic RHIS structure is shown to be limited to angles of incidence up to 40° for TE polarized waves and up to 35° for TM polarized waves. So the objective of this contribution is to present a second solution based on an anisotropic RHIS structure which presents good absorption of incident waves in TE and TM polarizations for larger angles of incidence. An example is presented for an incidence angle of 65°.     

Excitation of surface electromagnetic waves at an anisotropically conducting vacuum-metamaterial interface by the attenuated total internal reflection method

The excitation of well-localized oblique surface waves above the surface of a dielectric with a one-dimensional array of perfectly conducting wires is studied theoretically using the attenuated total internal reflection method. It is assumed that the distance between the wires and their diameter are much smaller than the surface wavelength. The frequencies of excited surface waves are much lower than the plasma frequency of the metal, and their electric field is orthogonal to the wires. It is shown that such surface waves can be excited with the help of a homogeneous TM wave as well as with the help of a homogeneous wave with an electric field polarized perpendicularly to the wires. It is found that in the course of excitation of oblique waves, the incident TM wave is partly polarized into a wave of the TE type.     

Transverse localization of Tamm plasmon in metal-DBR structure with disordered layer

Transverse localization of the optical Tamm plasmon(OTP) is studied in a metal-distributed Bragg reflector(DBR)structure with a one-dimensional disordered layer embedded at the interface between the metal and the DBR. The embedded disordered layer induces multiple scattering and interference of light, forming the light localization in the transverse direction. This together with the formation of Tamm plasmonic modes at the metal-DBR interface(i.e., the confinement of light in the longitudinal direction), gives birth to the so called transverse-localized Tamm plasmon. It is shown that for both transverse electric(TE) and transverse magnetic(TM) polarized light injection, the excited transverse-localized Tamm plasmon broadens and splits the dispersion curve due to spatial incoherence in the transverse direction, thus proving the stronger light confinement especially in the TE polarized injection. By adding the gain medium, specific random lasing modes are observed. The proposed study could be an efficient way of trapping and locally enhancing light on a subwavelength scale,which is useful in applications of random lasers, optical sensing, and imaging.     

Subwavelength gratings fabricated on semiconductor substrates via E-beam lithography and lift-off method

We present results of the fabrication and measurements on reflective polarizers consisting of stacked bi-layer subwavelength metal gratings prepared on GaAs (100) substrates. These linear gratings were fabricated using electron-beam direct-writing lithography and the lift-off method with periods less than the wavelength of light used for measurements. At normal incidence, the polarizer reflects the light polarized perpendicular to the grating lines (transverse magnetic polarization, TM polarized) but absorbs parallel-polarized light (transverse electric polarization, TE polarized). By optimizing structural parameters, the polarization extinction ratio close to 20 has been experimentally achieved at wavelength of 650 nm.     

Bessel beams: Effects of polarization

An approximation to a Bessel beam produced by tightly focusing linearly polarized light is known to produce a smaller central lobe than focusing plane polarized light. This is because the plane polarized wave gives a broad central lobe caused mainly by a parasitic longitudinal field component. It is known that this problem can be overcome by focusing radially polarized light. Here we demonstrate that other polarization distributions based on a linear combination of transverse electric (TE1) and transverse magnetic (TM1) fields can give a beam even narrower than for the radially polarized case. Special cases of this combination are identified, corresponding to the smallest width (TE1), and the maximum peak intensity compared with the side lobes (electric dipole polarization). Axially-symmetric forms can be generated by illumination with elliptically polarized light. A particular case is azimuthal polarization with a phase singularity, which is equivalent to TE1. For a semi-angular aperture of 60°, the TE1 case gives a central lobe width 9% narrower than for radially polarized illumination, while for plane polarized illumination it is 12% wider than the radially polarized case.     

Spiral modes supported by circular dielectric tubes and tube segments

The modal properties of curved dielectric slab waveguides are investigated. We consider quasi-confined, attenuated modes that propagate at oblique angles with respect to the axis through the center of curvature. Our analytical model describes the transition from scalar 2-D TE/TM bend modes to lossless spiral waves at near-axis propagation angles, with a continuum of vectorial attenuated spiral modes in between. Modal solutions are characterized in terms of directional wavenumbers and attenuation constants. Examples for vectorial mode profiles illustrate the effects of oblique wave propagation along the curved slab segments. For the regime of lossless spiral waves, the relation with the guided modes of corresponding dielectric tubes is demonstrated.     

二维光子晶体中与电磁波偏振态无关的自准直

利用有限时域差分法(FDTD)进行数值模拟，在二维光子晶体中实现了电磁波两种偏振态的自准直——全光自准直(full-light-self-collimation).研究表明，通过对光子晶体的结构做适当的调整，可以在较宽频率范围内实现横电波(TE波)和横磁波(TM波)沿着相同方向传播，同时保持较强的能流强度.全光自准直可以显著提高光源利用率和光波导的传播效率，在高密度集成光路中有非常重要的用途. 关键词： 光子晶体 偏振 自准直     

金属包层对称平面单轴晶体波导的模式场(Ⅱ)

对于晶体光轴平行于波导界面的结构,讨论了光在金属包层对称平面单轴晶体波导(波导层是单轴晶体,两个波导界面均为金属)内的传输特性.解析地得到了这种结构下波导模式场的精确解.模式场的性质因单轴晶体的性质不同而异.对于正单轴晶体,波导的主模是横电波,任何频率的光波均可激励该模式;当频率满足一定条件时,波导内传输单模,否则,将激励起高阶模式.高阶模既非TE波,也非TM波,而是两者耦合而成的混合模.对于负单轴晶体,波导的主模是一种混合模,该模式同样可被任何频率的光波所激励;当频率满足一定条件时,波导内传输单模,否则 关键词： 平面金属波导 单轴晶体 模式场 混合模     

Broadband,polarization-insensitive,and wide-angle microwave absorber based on resistive film

A simple design of broadband metamaterial absorber(MA) based on resistive film is numerically presented in this paper.The unit cell of this absorber is composed of crossed rectangular rings-shaped resistive film,dielectric substrate,and continuous metal film.The simulated results indicate that the absorber obtains a 12.82-GHz-wide absorption from about 4.75 GHz to 17.57 GHz with absorptivity over 90% at normal incidence.Distribution of surface power loss density is illustrated to understand the intrinsic absorption mechanism of the structure.The proposed structure can work at wide polarization angles and wide angles of incidence for both transverse electric(TE) and transverse magnetic(TM) waves.Finally,the multi-reflection interference theory is involved to analyze and explain the broadband absorption mechanism at both normal and oblique incidence.Moreover,the polarization-insensitive feature is also investigated by using the interference model.It is seen that the simulated and calculated absorption rates agree fairly well with each other for the absorber.     

Direct experimental observation of the single reflection optical Goos-Hänchen shift

We report a precise direct measurement of the Goos-H?nchen shift after one reflection off a dielectric interface coated with periodic metal stripes. The spatial displacement of the shift is determined by image analysis. A maximal absolute shift of 5.18 and 23.39 mum for TE and TM polarized light, respectively, is determined. This technique is simple to implement and can be used for a large range of incident angles.     

The coexistence of TE-TM surface waves in uniaxially anisotropic left-handed materials

We investigate theoretically the characteristics of surface waves in uniaxially anisotropic left-handed materials. The constraints for the existence of TE and TM polarized surface waves in uniaxially anisotropic left-handed materials are identified. We discuss mainly whether TE and TM polarized surface modes may coexist in the same frequency domain at the interface between one isotropic regular medium and another uniaxially anisotropic left-handed medium. It is shown that the answer to the coexistence of TE and TM surface modes is really positive. The Poynting vector and the density of energy associated with surface modes are calculated. Depending on the system parameters either TE or TM surface modes has the time averaged Poynting vector directed opposite or same to the mode phase velocity. In the presence of anisotropy, negative refraction does not need to be left-handed. We show that the characteristics of surface waves in uniaxially anisotropic left-handed media are significantly different from that in isotropic left-handed media.     

金属薄膜亚波长微结构的光束集束器件设计

利用时域有限差分方法,模拟了P偏振光高斯光束入射到金属银亚波长细缝与光栅结构的透射情况.由于表面等离子激元波的影响,对称光栅结构透射光呈现对称出射,而非对称结构可以实现小角度定方向的光束集束现象.借助公式推导法及Helmholtz互易定理,可设计出平行入射P偏振光的光束集束器件.由于高斯光束本身的发散性及近场分布的需要,针对高斯光束的器件在结构参量上缩小了12%.在对其他结构参量的优化的基础上,实现了针对633 nm高斯光束的对称出射及光束集束器件的设计.     

Guided modes in left-handed waveguides

We investigate basic properties of linear guided modes in a waveguide slab with the core of a material with simultaneously negative effective permittivity and permeability surrounded by a normal dielectric cladding. The existence and dispersion of all possible types of guided modes have been studied in detail. We demonstrate that the two orthogonally polarized, TE and TM slow guided modes, with the same frequency and the same wave number can exist simultaneously. Their group velocities, however, can be parallel or anti-parallel.     

非对称偏振分束光栅的矢量衍射优化设计

基于严格耦合波理论分析了一种非对称偏振分束光栅的设计。这种偏振分束光栅分别在1级和0级衍射级次上衍射TE和TM偏振波。介绍了利用遗传算法设计偏振分束光栅的方法,并给出了优化实例。仿真结果表明:在设计波长为1.55时,TE偏振波在1级的衍射效率大于93%,TM偏振波在0级的衍射效率大于99%,此时1级和0级的透射消光比分别达到了9914.1和46841.5。通过对设计结果的分析发现,该偏振分束光栅在设计波长附近100nm的波长范围内都具有较高的消光比(大于100),达到了较好的偏振分束效果。