亚波长介质偏振分束光栅的衍射特性

 采用严格耦合波理论并结合矩阵LU分解法,分析了亚波长介质光栅的刻槽深度、占空比、入射角、入射波长等参数对TE偏振和TM偏振0级衍射效率的影响。结果表明:在1 550 nm波长处,出现瑞利反常现象。由此提出利用瑞利反常现象设计工作波长为1 550 nm的偏振分束光栅,通过优化设计确定了最佳设计参数,即光栅周期为l0/2,瑞利入射角为30°,刻槽深为0.9l0,占空比为0.5。结果表明,参数优化后的偏振分束光栅可以使TE偏振0级反射波和TM偏振0级透射波同时达到近100%的衍射效率。     

亚波长介质光栅的闪耀特性分析

采用严格耦合波理论与矩阵LU分解法,求解了亚波长矩形介质光栅的衍射场,给出了TE和TM偏振波的耦合波方程组及其矩阵形式.通过数值计算分析了TE和TM偏振波的入射角、刻槽深度、入射波长等参量对＋1级衍射波衍射效率的影响.结果表明,当Λ=0.5λ0,θ=55°,d=0.38λ0,λ=10.6 μm时可以实现对TE偏振波＋1级的闪耀,衍射效率达到近90%,同时具有较宽广的角度适应范围.     

基于二维结构薄膜的偏振选择相位光栅的研究

利用二维结构薄膜构建了具有偏振选择特性的新型相位光栅,借助严格耦合波分析(RCWA)方法计算了光栅各级衍射强度随入射光波长及入射角的变化,发现在垂直入射情况下,波长600—640 nm范围内,相位光栅对横向电学(TE)模主要产生0级衍射,而对横向磁学(TM)模产生±1级衍射,在波长633nm处,0级衍射光的偏振消光比为109.8,±1级衍射光的偏振消光比为334.6.利用时域有限差分方法对这种相位光栅的偏振分束现象进行了模拟,偏振分离角在玻璃基板内可以达到10°左右,最后模拟了入射角为23°时光栅对不同偏     

高效全偏振矩形闪耀光栅的设计(英文)

入射光在光栅内传输时将激发产生离散模.本文采用模态法调节光栅内离散模的传输特性,使TE和TM偏振光所激发的0、1模为传输模,其余高阶模为消逝模.通过调控0模和1模间的累积相位差,对衍射光进行调控,实现了-1级近100%的高效衍射.采用模态法分三部设计了共振域的矩形全偏振闪耀光栅:1)根据光栅的共振条件给出光栅周期,光栅周期越大槽深越小;2)根据特征模方程计算出光栅占空比;3)根据耦合模条件计算机光栅槽深.实验结果表明,该光栅的TE和TM偏振光同时具备近100%的-1级衍射效率.给出了633nm波长-1级矩形石英全偏振闪耀光栅的典型设计实例,计算结果表明:所设计的全偏振闪耀光栅对TE和TM偏振入射光的-1级衍射效率分别高达96.7%和98.1%,且具有较宽的入射角及入射波长的变化适应范围,较大的制作容差.     

亚波长金属偏振分束光栅设计分析

结合有效介质理论和薄膜光学的抗反射设计方法,设计了基于0.65μm工作波长的亚波长金属偏振分束光栅,给出了光栅的优化设计参数,采用严格耦合波理论分析了光栅的偏振分束特性.结果表明,亚波长金属光栅对TE偏振表现为金属膜特性,具有高反射,对TM偏振表现为介质膜特性,具有高透射,在-30°<θ<30°的大入射角范围和0.47μm<λ<0.80μm的宽入射波谱内,该光栅的透射光和反射光均具有高偏振消光比和低插入损耗的特点. 关键词： 亚波长金属偏振分束光栅 有效介质理论 薄膜光学 严格耦合波理论     

基于耦合波理论设计偏振分束光栅

亚波长周期结构光栅具有传统光栅所不具有的特殊性质。针对通信中常用的1.55μm光波,采用严格耦合波理论分析了亚波长光栅的偏振分光特性,设计了对应的偏振分束光栅。所设计的光栅在入射角为56°时,透射消光比和反射消光比都大于9000,且在1.27μm~1.67μm全光波段内,入射角在51°~57°之间时,透射消光比和反射消光比都大于100,达到了宽带宽、宽角度以及透射消光比和反射消光比都较高的要求。     

高密度相位光栅的偏振选择性

高密度光栅具有与传统光栅不同的性质,其衍射特性往往是偏振相关的。本文针对1550nm波长TE/TM偏振入射光和0.5的光栅占空比,利用严格耦合波分析数值计算了不同光栅周期下0级及-1级的衍射效率。研究表明,相比周期为1550nm的光栅,当周期为1200nm时,偏振相关衍射效应明显增强,当光栅周期为890nm时,TE偏振光的衍射效率随着光栅深度呈正余弦变化,而TM偏振光的衍射效率始终集中在0级,具有偏振选择性。通过模式方法,利用模式中的有效折射率概念,研究了不同周期下被入射光所激发的两种光波模式通过光栅区域传播所累积的相位差;基于双光束干涉,模拟了0级和-1级的衍射效率。结果表明,利用严格耦合波分析的数值计算结果符合模式方法的理论预期,对于高密度相位光栅的偏振选择性给予了合理的物理机制解释。     

亚波长光栅偏振分束器的研究

利用单层亚波长硅光栅结构设计出工作在近红外波段的偏振分束器。该偏振分束器在45°入射角附近对TE偏振光具有很高的反射率同时对TM偏振光具有很高的透射率,其设计原理是基于亚波长光栅的泄漏模共振效应以及类布儒斯特效应。利用散射矩阵方法和时域有限差分方法对偏振分束器进行设计和分析。模拟结果显示,该偏振分束器在1390～1600nm的波长范围内的反射与透射消光比大于100;同时该偏振分束器具有相对较大的入射角度容差,在有限尺寸高斯光束入射下能保持很好的性能。     

亚微米光栅零级衍射特性的数值研究

用耦合波理论分析了亚微米光栅对光波场的衍射作用,给出了在TE和TM偏振入射条件下矩阵形式的耦合波方程,研究了光栅在TE偏振入射条件下可见光波段内的反射和透射零级衍射特性。亚微米光栅零级衍射效率是波长、偏振和入射角的函数,在不同照明、观察和光栅参数条件下,光栅零级衍射具有非常复杂的光谱结构,经过适当的优化光栅参数,零级衍射具有许多独特的衍射特性,在许多应用领域具有广泛的应用前景。     

多层介质膜偏振无关光栅的研制

介绍了一种应用于光纤激光光谱合束的高衍射效率多层介质膜偏振无关光栅的设计及制作,给出了设计参数、制作流程和最终制作的偏振无关光栅的测量结果,在1.044~1.084μm波长范围内,实验测得的TE偏振光、TM偏振光的平均衍射效率分别为89.7%,93.8%。     

Polarizing beam splitter of two-layer dielectric rectangular transmission gratings in Littrow mounting

We theoretically investigated the design of polarizing beam splitters (PBS) of two-layer dielectric rectangular transmission gratings in Littrow mounting. The PBS grating is aimed to separate TE and TM polarized waves into two different transmitted orders, i.e. the 0th and −1st orders. The polarization-dependent diffraction process is analyzed by using a simplified modal method. The mode reflection and transmission at the interface of the two layers are illustrated. Design equations are given based on the average mode indices of the even and odd modes inside the grating region, which are verified by using rigorous coupled wave analysis. Moreover, with simulated annealing algorithm, two kinds of two-layer PBS gratings are optimized for operation over the C-band (1520-1570 nm). Compared with the single-layer transmission PBS gratings, such two-layer scheme exhibits a great flexibility of design. The PBSs of two-layer dielectric transmission gratings should be useful for practical applications.     

Polarizing beam splitter of a deep-etched fused-silica grating

We described a highly efficient polarizing beam splitter (PBS) of a deep-etched binary-phase fused-silica grating, where TE- and TM-polarized waves are mainly diffracted in the -1st and 0th orders, respectively. To achieve a high extinction ratio and diffraction efficiency, the grating depth and period are optimized by using rigorous coupled-wave analysis, which can be well explained based on the modal method with effective indices of the modes for TE/TM polarization. Holographic recording technology and inductively coupled plasma etching are employed to fabricate the fused-silica PBS grating. Experimental results of diffraction efficiencies approaching 80% for a TE-polarized wave in the -1st order and more than 85% for a TM-polarized wave in the 0th order were obtained at a wavelength of 1550 nm. Because of its compact structure and simple fabrication process, which is suitable for mass reproduction, a deep-etched fused-silica grating as a PBS should be a useful device for practical applications.     

Theoretical reflective performance of a sandwiched two-layer grating polarizer

The reflective polarizer is described by a sandwiched two-layer grating with a metal slab. Such a new polarizer is aimed to improve the performance of a reflective grating-based polarizer. The grating is optimized with the usual duty cycle of 0.5, where TE and TM polarizations are reflected in the –1st and the 0th diffraction orders, respectively. With optimized grating parameters, the extinction ratio can reach 45.5 dB and 41.9 dB in two diffraction orders, which are greatly improved compared with the conventional reported surface grating polarizer with the simple structure. Attractive merits of the new design are high efficiency, high extinction ratio, wide incident wavelength bandwidth for TE polarization, and wide angular range for TM polarization. Numerical results are expected to open new opportunities for the design of a grating-based polarizer with the enhanced performance by the complicated grating configuration.     

Polarizing beam splitter of deep-etched triangular-groove fused-silica gratings

We investigated the use of a deep-etched fused-silica grating with triangular-shaped grooves as a highly efficient polarizing beam splitter (PBS). A triangular-groove PBS grating is designed at a wavelength of 1550 nm to be used in optical communication. When it is illuminated in Littrow mounting, the transmitted TE- and TM-polarized waves are mainly diffracted in the minus-first and zeroth orders, respectively. The design condition is based on the average differences of the grating mode indices, which is verified by using rigorous coupled-wave analysis. The designed PBS grating is highly efficient over the C+L band range for both TE and TM polarizations (>97.68%). It is shown that such a triangular-groove PBS grating can exhibit a higher diffraction efficiency, a larger extinction ratio, and less reflection loss than the binary-phase fused-silica PBS grating.     

Connecting-layer-based polarizing beam splitter grating with high efficiency for both TE and TM polarizations

We describe a novel polarizing beam splitter (PBS) of transmission connecting-layer-based grating, which can show high efficiency for TE polarization in the ?1st order and TM polarization in the 0th order. According to the modal method, grating duty cycle and period are prescribed to obtain high efficiency for TM polarization. Using the rigorous coupled-wave analysis, grating depth and thickness of the connecting layer are optimized to achieve high efficiency for TE polarization. The presented PBS has advantages of wideband properties for incident wavelength and angle. Most importantly, the efficiency is improved greatly for TE polarization compared with the reported PBS based on fused-silica grating.     

Polarization-sensitive propagation in an anisotropic metamaterial with double-sheeted hyperboloid dispersion relation

The polarization-sensitive propagation in the anisotropic metamaterial (AMM) with double-sheeted hyperboloid dispersion relation is investigated from a purely wave propagation point of view. We show that TE and TM polarized waves present significantly different characteristics which depend on the polarization. The omnidirectional total reflection and oblique total transmission can occur in the interface associated with the AMM. If appropriate conditions are satisfied, one polarized wave exhibits the total refraction, while the other presents the total reflection. We find that the opposite amphoteric refractions can be realized by rotating the principle axis of AMM, such that one polarized wave performs the negative refraction, while the other undergoes positive refraction. The polarization-sensitive characteristics allow us to construct two types of efficient polarizing beam splitters under certain achievable conditions.     

基于金属狭缝阵列的各向异性偏振分束器

在金属-电介质结构的基础上提出了一种基于金属狭缝阵列的各向异性偏振分束器,并采用有限元法研究了横磁(TM)和横电(TE)偏振光入射后结构所表现出的负反射和镜面反射等特性.计算结果表明,当偏振光的入射角设定在20?—70?时,入射的TM光发生强烈的负反射,而TE光的负反射很弱,并随着波长的增加而急剧下降.分析可得偏振分束光栅的理想负反射点和反射面的完美对称响应效果.通过仿真得到了理想负反射点的取值范围.结合严格耦合波法软件,计算不同偏振光入射时负反射和镜面反射条件下的反射率,其消光比高达10~6.