激光等离子体效应对薄膜损伤特性的影响

高能激光的发展对光学元件的抗损伤能力要求越来越高,其中光学薄膜是最薄弱的环节之一。实验研究了激光的聚焦位置对石英基片上HfO2/SiO2减反射薄膜损伤形貌的影响,研究发现:激光等离子体的高压冲击波对薄膜产生强烈的冲击剥离效应,其压强随膨胀半径的增加而迅速减小。激光等离子体光谱的辐射波长小于入射激光波长,这会增强薄膜对辐射光能量的吸收;位于深紫外波段、能量大于HfO2薄膜带隙的光子能量,将被薄膜直接吸收,从而加剧薄膜的电离破坏。激光等离子体的辐射效应和冲击波效应的共同作用决定了薄膜的损伤形貌。当激光聚焦到薄膜表面时,冲击波压强极大会使薄膜发生大面积的电离去除,同时基底发生击穿;当两者距离大到一定距离时,冲击波只会使得中心处小面积薄膜发生剥离,基底未出现断裂。     

退火对EBE,IBS和ALD沉积HfO2薄膜的抗激光损伤性能影响

结合自身实验条件采用电子束蒸发(EBE)、离子束溅射(IBS)和原子层沉积(ALD)三种工艺制备了HfO2薄膜,对其进行退火实验,采用1064 nm Nd:YAG激光测定了即时沉积和退火后各HfO2薄膜的抗激光损伤能力。研究发现,ALD HfO2薄膜的激光损伤阈值最高,EBE HfO2薄膜次之,IBS HfO2薄膜的损伤阈值最低;300℃退火对各工艺薄膜抗激光损伤能力的影响均为负面,500℃退火则会显著降低ALD HfO2薄膜的抗激光损伤能力。     

HfO_2单层膜的吸收和激光损伤阈值测试

薄膜吸收是降低膜层激光损伤阈值的重要原因,为了研究薄膜吸收对激光损伤阈值的影响,对HfO2单层膜在1 064 nm处的吸收及其在不同波长激光辐照下的损伤阈值进行了测试和分析。研究结果表明:薄膜的激光损伤阈值由薄膜吸收平均值(决定于薄膜中缺陷的种类和数量)和吸收均匀性(决定于薄膜中缺陷的分布)共同决定;根据HfO2单层膜在1064 nm波长处的吸收值,不但可以定性判断薄膜在1 064 nm波长,而且还可以判断在其它波长激光辐照下的抗激光损伤能力。     

原子层沉积HfO_2薄膜的激光损伤特性分析

以目前激光惯性约束聚变中应用最广泛的高折射率材料二氧化铪(HfO2)为研究对象,在熔石英基底上分别采用TEMAH和HfCl4前驱体制备了HfO2薄膜,沉积温度分别为100,200和300℃。采用椭偏仪和激光量热计对薄膜的光学性能进行了测量分析,采用X射线衍射仪(XRD)对薄膜的微结构进行了测量。最后在小口径激光阈值测量平台上按照1-on-1测量模式对薄膜的损伤阈值进行了测试,并采用扫描电子显微镜(SEM)对损伤形貌进行了分析。研究表明,用同一种前驱体源时,随着沉积温度升高,薄膜折射率增加,吸收增多,损伤阈值降低。在相同温度下,采用有机源制备的薄膜更容易在薄膜内部形成有机残留,导致薄膜吸收增加,损伤阈值降低。采用HfCl4作为前驱体源在100℃制备氧化铪薄膜时,损伤阈值能够达到31.8J/cm2(1064nm,3ns)。     

PECVD技术制备单层光学薄膜抗激光损伤特性研究

采用PECVD技术在BK7玻璃基底上沉积了不同厚度的单层SiO2（折射率为1.46）和SiNx（折射率为1.84）光学薄膜,并对这2种膜层进行抗激光损伤阈值（LIDT）测试,分析讨论了PECVD技术制备的单层光学薄膜与抗激光损伤特性之间的关系。实验结果表明:PECVD技术制备的单层SiO2薄膜有较高的LIDT,薄膜光学厚度在o/4~o/2之间时,在光学厚度为350 nm时,LIDT有最小值21.7 J/cm2,光学厚度为433 nm时,LIDT有最大值27.9 J/cm2。SiNx薄膜的LIDT随着光学厚度增加而减小,在光学厚度为o/4时,LIDT有最大值29.3 J/cm2,光学厚度为o/2时,LIDT有最小值4.9 J/cm2。     

激光诱导击穿光谱在薄膜损伤分析中的应用

提出了应用激光诱导击穿光谱技术对薄膜损伤特性进行表征的方法,研究了纳秒脉冲激光作用下薄膜损伤时的等离子体光谱特征,并应用该技术对薄膜的抗激光损伤特性进行了测量.实验测得,HfO2单层膜在78mJ的激光能量的辐照下,薄膜损伤时的等离子体温度为2 807.4K,且电子密度为7.4×1017cm-3.利用识别薄膜损伤时的等离子体光谱的特征,准确地判断了薄膜是否损伤,避免了薄膜损伤的误判现象.结果表明,激光诱导击穿光谱技术适用于薄膜的激光损伤测试中,并且是一种非常有效的测试分析方法.     

缺陷对HfO2薄膜的激光弱吸收与损伤阈值的影响

激光弱吸收是导致光学薄膜损伤的重要原因。在(5~43)mPa的氧分压下制备并测试了一组HfO2薄膜。实验发现,当氧分压小于20mPa时,薄膜弱吸收越大,损伤阈值越低;当氧分压大于20mPa时,薄膜的损伤阈值与弱吸收并不一一对应,具有较高弱吸收的薄膜可能同时具有较高的损伤阈值。建立了缺陷模型,采用有限元法模拟了缺陷对弱吸收测量和损伤阈值测量的影响,分析了缺陷尺寸、密度、吸收系数对弱吸收和损伤阈值的影响。研究结果显示,吸收系数高于薄膜1 000倍的缺陷可以降低薄膜的损伤阈值1 000倍,却并不影响薄膜的弱吸收。缺陷对HfO2薄膜的激光弱吸收与损伤阈值测试有完全不同的影响,是导致某些薄膜弱吸收与损伤阈值背离的原因。     

1064 nm激光对中性密度滤光片的损伤机理研究

中性密度滤光片的典型结构是在K9玻璃上镀金属膜,来实现对激光的有效吸收.由于损伤阈值较低,严重限制了其在高能激光系统中的应用.实验研究了较高激光能量密度下滤光片的损伤形貌和损伤机理.损伤形貌的变化特征是:随着激光能量密度的增加,滤光片先出现损伤点,后以损伤点为中心产生裂纹,且裂纹长度逐渐变长,最终连接成线状和块状,导致大面积的薄膜脱落.建立了缺陷吸收激光能量升温致中性密度滤光片表面薄膜损伤的模型,计算了薄膜表面的温度和应力分布,讨论了薄膜表面不均匀温升造成的径向、环向和轴向热应力分布.理论分析显示:环向应力是造成薄膜沿径向产生裂纹的主要原因.当激光能量密度大于约2.2 J/cm²,杂质粒子半径大于140 nm且相邻杂质粒子之间的距离小于10 μ m时,裂纹才能大量连接起来引起薄膜的大面积脱落.     

激光诱导多层光学薄膜损伤分析与仿真

提出一种全面分析光学薄膜损伤特性的方法,根据热传导理论与电子增殖理论建立激光辐照下多层介质膜的损伤理论模型。以HfO₂/SiO₂多层高反膜为例,计算红外纳秒脉冲激光作用下膜系内部的温度场、应力场以及自由电子数密度分布,对其热学特性与电子增殖特性进行综合评估后,得到不同输入条件下膜系的损伤阈值。结果表明,薄膜材料的损伤特性会受到驻波场的影响,在1064 nm波长的激光辐照下HfO₂/SiO₂ 多层介质薄膜的热致应力损伤效应先于热熔融效应先于场效应发生,且薄膜中SiO₂层发生热损伤,而薄膜并未发生场损伤,此外薄膜的损伤阈值随着激光脉宽的增大而增大。     

单脉冲和多脉冲飞秒激光对单层光学薄膜的损伤

 利用掺钛的蓝宝石飞秒激光系统输出的单脉冲和多脉冲飞秒激光(中心波长800 nm，脉宽50 fs，靶面聚焦直径Ф 40 μm)，分别对BK7玻璃基底上厚约500 nm的单层HfO₂和单层ZrO₂薄膜进行辐照，得到了这两种薄膜在1-on-1和1 000-on-1测试方法下的激光损伤阈值。实验发现，两种方法下HfO₂单层膜的阈值均比ZrO₂单层膜的阈值高。从简化的Keldysh多光子离化理论出发，认为HfO₂薄膜材料的带比ZrO₂的宽是导致上述结果的主要原因。同时，同一种薄膜的多脉冲下的阈值比单脉冲下的低，原因是多脉冲下，飞秒激光对光学薄膜的损伤存在累积效应。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.