纳米碳管的电化学贮锂性能

用透射电镜、高分辨透射电镜、X射线衍射和拉曼光谱表征了用催化热解法制备的纳米碳管的结构,研究了纳米碳管的电化学嵌脱锂性能。以纳米级铁粉为催化剂热解乙炔气得到的纳米碳管石墨化程度较低,结构中存在褶皱的石墨层、乱层石墨和微孔等缺陷,具有国交高的贮锂容量,初始容量为640mAh/g,但循环稳定性较差。而以纳米级氧化铁粉为催化剂热解乙烯得到的纳米碳管结构比较规则,循环稳定性较好,但贮锂容量较低,初始容量为282mAh/g。讨论了纳米碳管的结构对其温度特性和不同电流密度下的充放电容易的影响。     

表面修饰SrTiO3光催化剂纳米碳管的光电化学嵌锂特性

采用直接水解沉淀的方法制备了钙钛矿型SrTiO3纳米粒子,并将其修饰在纳米碳管表面形成SrTiO3/CNTs纳米复合材料,研究了SrTiO3/CNTs电极在氙灯照射下的光电化学嵌锂特性．实验结果表明,光照射对CNTs电极的嵌锂容量影响不大,而SrTiO3/CNTs电极受光照时的嵌锂容最高达251 mAh/g,远高于无光照下的嵌锂容量(170 mAh/g)．循环伏安测试也表明光照射可显著提高嵌脱锂反应电流．这可归因于SrTiO3光催化剂受光照射而诱发的纳米碳管嵌锂反应．     

离子束辅助沉积硅薄膜负极材料的研究

采用离子束辅助沉积法制备了锂离子电池硅薄膜负极材料,研究了硅薄膜的晶体结构、表面形貌和电化学性能.研究结果表明：硅薄膜是非晶态的结构;非晶态硅薄膜发生嵌脱锂反应的电位分别为0.03 V与0.34 V和0.16 V与0.49 V;硅薄膜表现出很高比容量和充放电效率,其可逆比容量和库仑效率分别为3134.4 mAh/g和87.1％;硅薄膜具有优异的循环性能,在0.5C倍率下200次循环后容量保持率为92.2%. 关键词： 硅薄膜 离子束辅助沉积 锂离子电池 负极材料     

纳米氧化锡负极材料锂化反应机理的原位透射电镜研究

二氧化锡(SnO_2)材料因具有储量丰富、理论容量高、嵌脱锂电位安全等一系列优点,在锂离子电池负极材料研究中受到广泛关注.然而, SnO_2纳米材料在锂化反应过程中的机理,尤其是第一步转化反应是否可逆尚存在争议.本文利用常规水热法成功制备了平均粒径为4.4 nm的SnO_2纳米颗粒,并在透射电子显微镜中构建了微型锂离子电池原型器件,对SnO_2纳米颗粒在充放电过程中的微观形貌和物相演变进行原位表征.实验结果表明, SnO_2纳米颗粒在嵌锂过程中率先生成了纳米尺寸的中间相Sn,随后发生了合金化反应转变为Li_(22)Sn_5相.脱锂反应后, Li_(22)Sn_5相转变为SnO_2.分析认为,纳米晶界阻碍了Sn颗粒的聚集长大,使得Sn和Li_2O能够充分接触,进而使脱锂反应能够完全进行,生成SnO_2.研究结果对于如何提高SnO_2基电极材料可逆比容量和循环性能具有一定的指导意义.     

硅纳米团簇与石墨烯复合结构储锂性能的第一性原理研究

本文采用第一性原理计算方法, 研究了不同晶向硅纳米团簇与石墨烯复合结构稳定性及其储锂性能. 计算了不同高度、大小硅团簇与石墨烯复合结构的结合能, 复合结构中嵌锂吸附能和PDOS. 分析表明, 硅团簇和石墨烯之间形成较强的Si—C键, 其中[111]晶向硅团簇与石墨烯作用的形成能最高, 结构最为稳定. 进一步计算其嵌锂吸附能, 发现硅团簇中靠近石墨烯界面处的储锂位置更加有利于锂的吸附, 由于锂和碳、硅之间有较强电荷转移, 其吸附能明显大于其他储锂位置. 同时在锂嵌入过程中, 由于石墨烯的引入, 明显减小了界面处硅的形变, 有望提高其作为锂电池负极材料的可逆容量.     

以LiCoO2为阴极的全固态薄膜锂电池的研究

采用射频磁控溅射技术制备了非晶态和不同取向的多晶LiCoO2薄膜,利用XRD和SEM研究了不同温度退火后LiCoO2薄膜的结构和形貌.以具有不同结构的LiCoO2薄膜为阴极、含氮磷酸锂薄膜为电解质以及金属锂薄膜为阳极,成功地制备了电化学性能不同的全固态薄膜锂电池.由电化学研究结果表明,LiCoO2薄膜的结构和多晶取向决定了薄膜电池的电化学性能.采用具有一定取向的多晶LiCoO2薄膜制备的全固态薄膜锂电池具有最佳的性能,稳定放电容量达到55.4μAh/cm2μm,充放电循环次数超过450次.     

Co_2SnO_4/Graphene复合材料的制备与电化学性能研究

实验首先采用改进的Hummers法制备氧化石墨,然后以氧化石墨烯为前驱体,通过水热法将锡酸钴纳米颗粒均匀镶嵌在石墨烯薄膜基片上,最终获得Co2SnO4/Graphene镶嵌复合材料.采用X射线衍射(XRD)、扫描电子显微镜(SEM)对材料的结构和形貌进行表征,通过恒电流充放电(CC)、循环伏安法(CV)与交流阻抗法(EIS)测试了材料的电化学性能.实验结果表明,石墨烯良好的分散性及较高的电子导电率,可以提高锡酸钴材料的电化学性能,材料首次可逆容量达到1415.2 mA·h/g,50次循环后仍能保持469.7 mA·h/g的放电比容量.     

Li-Sn合金负极材料的嵌脱锂机理研究

采用基于密度泛函理论的第一性原理平面波赝势方法计算了Li-Sn各种合金相的物理性质和电化学性质,计算发现Li₅Sn₂相对膨胀率小、对可逆容量贡献大,是理想的合金电极相.同时采用直流和射频磁控溅射方法制备了纳米Sn薄膜电极,并将测得的电化学特性与计算得到的性能进行了比较,发现理论计算的嵌锂电位与实验测得的嵌锂电位具有较好的一致性. 关键词： 锂离子电池 Li-Sn合金 体积膨胀率 第一性原理     

Co$lt;sub$gt;2$lt;/sub$gt;SnO$lt;sub$gt;4$lt;/sub$gt;/Graphene复合材料的制备与电化学性能研究

实验首先采用改进的Hummers法制备氧化石墨,然后以氧化石墨烯为前驱体,通过水热法将锡酸钴纳米颗粒均匀镶嵌在石墨烯薄膜基片上,最终获得Co₂SnO₄/Graphene镶嵌复合材料. 采用X射线衍射（XRD）、扫描电子显微镜（SEM）对材料的结构和形貌进行表征,通过恒电流充放电（CC）、循环伏安法（CV）与交流阻抗法（EIS）测试了材料的电化学性能. 实验结果表明,石墨烯良好的分散性及较高的电子导电率,可以提高锡酸钴材料的电化学性能,材料首次可逆容量达到1415.2 mA·h/g,50次循环后仍能保持469.7 mA·h/g的放电比容量. 关键词： 2SnO₄')" href="#">Co₂SnO₄ 石墨烯 电化学性能 锂离子电池     

4A碳纳米管及相关结构的嵌锂特性(英文)

碳纳米管独特的一维结构和强烈的卷曲效应为外来原子提供了理想的嵌入通道。本文全面总结了近年来我们对直径仅为4A的三种单壁碳纳米管嵌锂特性的密度泛函研究工作。我们具体讨论了体系嵌锂后的结构、能量、电子、电化学等特性。由于这些超小直径的碳纳米管最初合成于沸石晶体的纳米管道,我们也讨论了碳纳米管?沸石晶体复合体系的嵌锂特性。另外,我们还研究了由(5,0)和(14,0)碳纳米管组成的双壁碳纳米管体系的嵌锂特性。我们的理论计算表明,超小直径碳纳米管及相关结构作为锂离子电池负极材料具有很好的应用前景。     

Self-organization of five species in a cyclic competition game

Cyclic competition game models, particularly the “rock–paper–scissors” model, play important roles in exploring the problem of multi-species coexistence in spatially ecological systems. We propose an extended “rock–paper–scissors” game to model cyclic interactions among five species, and find that two of the five can coexistent when biodiversity disappears, which is different from the “rock–paper–scissors” game. As the number of fingers is five, we named the new model the “fingers” game, where the thumb, forefinger, middle finger, ring finger, and little finger cyclically dominate their subsequent species and are dominated by their former species. We investigate the “fingers” model in two ways: direct simulations and nonlinear partial differential equations. An important finding is that the number of species in a cyclic competition game has an influence on the emergence of biodiversity. To be specific, the “rock–paper–scissors” model is in favor of maintaining biodiversity in comparison with the “fingers” model when the variables (population size, reproduction rate, selection rate, and migration rate) are the same. It is also shown that the mobility and reproduction rate can promote or jeopardize biodiversity.     

Contrastive analysis on tone between Putonghua and Taiwan Mandarin

The differences of the pitch and duration of Chinese syllables between Putonghua （PTH） and Taiwan Mandarin （TM） were studied. The speech materials to be used are not only isolated syllables, but also sentences. The results reveal that： For the isolated syllables, T1 and T2 in TM are influenced by Minnan dialect, therefore their pitch are lower than those in PTH. T3 is fall-rise in PTH, while it is fall in TM. Moreover, the syllable duration sequence for different tone is T3〉T2〉T1〉T4 in PTH, while it is T1〉T2〉T3〉T4 in TM. For the syllables in sentences, T2 is mid-rise in PTH, while it is mid-level in TM. And the T3 is longer than T4 but shorter than T1 or T2 in PTH, while it is the shortest in TM. Furthermore the effects of prosodic phrase boundary on duration for different tones are almost the same in PTH, but the lengthening part of T1 or T2 is longer than that of T3 or T4 in TM.     

Experimental study on downstep in Chinese intonation

Downstep in pitch contour of Chinese Putonghua is examined using subtly designed sentences by controlling tone combinations. The results show both automatic and nonautomatic downstep phenomena exist in Chinese. In non-automatic downstep, low tones compress downwards the pitch range of the following syllables. and the main influence of downstep is on topline. Low tone not only lower the topline behind it, but also raise the high tones before it, the effects are compatible with each other. In automatic downstep, the topline of pitch contour in intonational phrase is presented as a linear downtrend, but it differs among speakers due to the effect of personal stress practice. In comparison with downstep phenomenon in other tone or non-tone languages, the downstep ratio in Chinese is not constant, and the domain of downstep is not limited within the adjacent tones.     

Abelian-Higgs phase of SU(2) QCD and glueball energy

It is shown that SU(2) QCD admits an dual Abelian-Higgs phase, with a Higgs vacuum of a type-Ⅱ superconductor. This is done by using a connection decomposition for the gluon field and the random-direction approximation. Using a bag picture with soft wall, we presented a calculational procedure for the glueball energy based on the recent proof for wall-vortices [Nucl. Phys. B 741(2006)1].     

Signal generation in an isotropic medium in scanning electron acoustic microscope

Based on the research in Ref. [5][Materials Science and Engineering, 1989; A122： 57 63], an improved model of heat source is set up, the different modes of Lamb wave in an isotropic sample generated by a chopped electron beam at frequency f are obtained with integral transform and normal function expansion method, and the output signal of PZT coupled at the back surface of the sample is found out. The generation mechanism of SEAM （Scanning Electron Acoustic Microscopy） signal is discussed. It shows that the SEAM is a near field imaging technique with high spatial resolution and its best lateral spatial resolution is about 2√2α （α is the radius of the focused electron beam）. Some of experimental results of SEAM images are presented in the paper and it shows that the spatial resolution of SEAM is better than 0.5 μm and smaller than the thermal diffusion length of the sample. Therefore the character of near field imaging in SEAM is also proved experimentally.     

High efficiency filtering using two-dimensional photonic crystal coupled cavity structures

Transmission spectra of coupled cavity structures (CCSs) in two-dimensional (2D) photonic crystals (PCs) are investigated using a coupled mode theory, and an optical filter based on CCS is proposed. The performance of the filter is investigated using finite-difference time-domain (FDTD) method, and the results show that within a very short coupling distance of about 3λ, where λ is the wavelength of signal in vacuum, the incident signals with different frequencies are separated into different channels with a contrast ratio of 20 dB. The advantages of this kind of filter are small size and easily tunable operation frequencies.     

Real-time restoration of rotational blurred image using gradient-loading

The key to the restoration of rotational motion blurred image is how to restore the image under a low cost and to correct the irreversibility of the degradation function matrix.Based on the special qualities of degradation function matrix and precise deduction in space-domain, we present a new approach using gradient-loading for restoration of rotational blurred image.By easily adding a gradient operator, the irreversibility of the original matrix is corrected and can be applied for inverse filtering then.Gradientloading is the optimized approach which combines the advantages of both the approaches using constrained least square filtering and traditional diagonal-loading.Compared with the approach using least square filtering, its peak signal-to-noise ratio (PSNR) is improved from 3.18 to 6.46dB, while the computing time is reduced to 1/2-1/3.Experimental results demonstrate the effectiveness, noise-resistibility, robustness, and low complexity of this approach, which make it more suitable for real-time environment.     

All-Optical Logic Device Using Bent Nonlinear Tapered Y-Junction Waveguide Structure

We propose an all-optical logic device made of a bent tapered Y-junction waveguide with a Kerr-type nonlinear interface. It could provide an AND gate, OR gate, and exclusive-OR (XOR) gate. We could obtain different transmission results by adjusting the bending angle. The numerical simulation results show that the device functions as AND, OR, and XOR gates.     

Real-time, continuous-wave terahertz imaging by a pyroelectric camera

Real-time, continuous-wave terahertz (THz) imaging is demonstrated. A 1.89-THz optically-pumped farinfrared laser is used as the illumination source, and a 124 × 124 element room-temperature pyroelectric camera is adopted as the detector. With this setup, THz images through various wrapping materials are shown. The results show that this imaging system has the potential applications in real-time mail and security inspection.