紫外光固化聚丙烯酰/SiO2有机/无机杂化气凝胶制备

 采用自制的甲基丙烯酰多羟基倍半硅氧烷制备了UV固化的有机/无机杂化湿凝胶。湿凝胶经CO₂超临界干燥后即得到相应的杂化气凝胶,气凝胶经场发射扫描电子显微镜,高分辨透射电镜分析表明：构成气凝胶3维珍珠链结构的骨架的颗粒尺寸为20～30 nm,骨架上具有5～10 nm的孔洞结构,骨架颗粒有机、无机组分间没有明显的相界面。气凝胶的比表面积、吸附特性和微观孔结构采用经典的N₂吸附法获得,结果表明气凝胶比表面积为520.9 m²/g,孔洞结构主要由50 nm以下的介孔所构成。     

溶剂对块体La基气凝胶性能的影响

采用溶胶-凝胶工艺,以氯化镧(LaCl3·7H2O)为前驱体,以甲醇和乙醇为溶剂,聚丙烯酸为分散剂,环氧丙烷为凝胶促进剂,分别合成两种性能不同的稀土La基气凝胶。采用扫描电子显微镜、傅里叶红外光谱仪、比表面积与孔径分析仪、力学性能测试仪对不同溶剂制备的两种稀土La基气凝胶的微观结构、成分、比表面积、孔径分布和力学性能进行了研究表征。结果表明,以甲醇和乙醇为溶剂制备的稀土La基气凝胶都具有纳米多孔材料的典型特征,由大量nm量级的球形和长条形颗粒胶连而成,孔洞结构丰富。以乙醇为溶剂制备的稀土La基气凝胶的网络骨架更纤细,孔洞更大,比表面积达到220m2·g-1,密度约为160mg·cm-3,但力学性能较差。而以甲醇为溶剂制备的稀土La基气凝胶的网络骨架更强壮,孔洞更小,比表面积达到95m2·g-1,密度约为350mg·cm-3,力学性能较好。样品性能上的差异可能是由甲醇的极性比乙醇的极性强引起的。     

低密度稀土氧化物基气凝胶靶的研制

低密度的高原子序数元素氧化物气凝胶由于前驱体形成端基双键而易于收缩和开裂。通过调控配位环境结合无机分散溶胶凝胶法,制备了稀土氧化物气凝胶。氧化镧基气凝胶和氧化钇基气凝胶块体的成型性好,最低密度分别为0.05g·cm-3和0.06g·cm-3。其成分分别为六方相的La(OH)3和六方相的Y(OH)3,而聚丙烯酸中的羧基与稀土离子之间以桥接的方式进行配位。两种气凝胶均存在明显的多级结构,氧化镧基和氧化钇基气凝胶的初级粒子分别为纤维状和片/球混合形貌,而其二级粒子均为球形。两种气凝胶的比表面积分别为229.1m2·g-1和229.6m2·g-1。该方法制备的稀土氧化物气凝胶具有低的密度和纳米尺度的均匀性,在背光源中有潜在的应用。     

浸渍过程对纳米纤维素/二氧化硅复合气凝胶结构与性能研究

纳米纤维素(CNF)气凝胶兼具传统气凝胶的优异特性和自身优良的生物相容性和可降解性,在很多领域应用前景广阔。然而纤维素自身的超亲水性严重限制了其更广泛的应用,为改善纤维素气凝胶的亲水性能,提高其综合应用性能,采用简单浸渍法在纤维素气凝胶基体中引入二氧化硅(SiO₂)颗粒制备纳米纤维素/二氧化硅复合气凝胶,利用傅里叶红外光谱仪(FTIR)分析纤维素气凝胶和复合气凝胶的化学结构;用扫描电镜(SEM)观察气凝胶的微观结构;测定气凝胶的物理、力学性能和接触角。结果表明,复合气凝胶在3 340 cm-1处-OH吸收峰较纤维素气凝胶均有所减弱,表明SiO₂的引入促使Si-OH形成,也降低了气凝胶的亲水性,同时有Si-CH₃和Si-O-Si吸收振动峰出现,表明三甲基氯硅烷(TMCS)的改性作用以及纤维素与SiO₂颗粒之间形成稳定化学键连接。浸渍时间影响硅含量,进而影响气凝胶的密度、比表面积和孔隙率。当浸渍时间为10 min时制备的复合气凝胶性能较好,其微观结构分布均匀,具有疏水性能,接触角可达152°,同时气凝胶仍具有较好的力学性能和较低密度,其压缩模量和压缩性能分别为5.91和1.38 MPa,密度为0.1 g·cm-3。     

对苯二酚-甲醛碳气凝胶的制备

 溶胶-凝胶法制备了高HC比（10~40，对苯二酚与催化剂(Na₂CO_{3/sub>)的物质的量之比）的对苯二酚-甲醛有机气凝胶，并经高温碳化处理得到其碳气凝胶。借助有机气凝胶的红外光谱研究了其化学结构，说明其网孔结构形成的可能性；研究了有机气凝胶的扫描电镜图像、比表面积及孔径分布等，并得到碳化前后的一些对比数据：有机气凝胶颗粒大小30~50 nm，碳化后约为10 nm，比表面积从341.77 m²/g增大到452.75 m²/g，密度从0.170 8 g/cm^{3/sup>增大到0.335 6 g/cm3/sup>。}}     

共水解法制备GeO_2/SiO_2复合气凝胶初步研究

采用先共水解正硅酸乙酯和乙醇锗混合溶液、后以胺类化合物作为凝胶催化剂的方法制备了GeO2/SiO2复合氧化物湿凝胶,再将湿凝胶经超临界流体干燥获得了相应的复合氧化物气凝胶。对气凝胶的场发射扫描电镜和高分辨透射电镜分析表明,气凝胶为存在致密纳米团簇的网络结构。电子能谱分析表明,致密的纳米颗粒由富含GeO2的溶胶颗粒堆积而成,网络结构则主要以SiO2为主,这说明在"一锅法"制备复合气凝胶的过程中,GeO2将优先形成nm量级的颗粒而掺杂到SiO2气凝胶网络中。     

辐照还原法制备Au掺杂MF气凝胶

利用辐照还原法在500 kGy辐照剂量下制备了Au掺杂MF有机气凝胶。通过X射线衍射（XRD）、能量色散光谱仪（EDX）和透射电子显微镜（TEM）测试证实了辐照法成功地制备出Au掺杂MF有机气凝胶复合物。EDX和TEM照片表明辐照处理后Au纳米颗粒均匀地分布在MF气凝胶骨架中,并且Au纳米颗粒的平均尺寸为5.8 nm。N2吸附数据分析表明掺入Au纳米颗粒后,MF气凝胶的比表面积、总孔体积、微孔体积和介孔体积都有所下降。     

超高比表面积碳气凝胶常压干燥制备与结构分析

以间苯二酚(R)-甲醛(F)为原料,加入表面活性剂P123以增强材料的骨架强度的方法,采用常压干燥技术制备了RF碳气凝胶,并进行了二氧化碳活化以调节其孔结构。扫描电子显微镜(SEM)测试表明,常压干燥的碳气凝胶结构中具有更大的纳米颗粒,骨架结构变粗,活化使碳气凝胶骨架结构更加致密;红外吸收光谱(FTIR)表明,表面活性剂P123中的醚键与RF苯环中的羟基存在强的相互作用,碳化后P123特征峰消失;热重曲线(TG和DTG)分析说明P123在440 ℃左右分解完全,不会对碳气凝胶的成分产生影响,并能起到良好的造孔作用;氮气吸附表明常压干燥制备的碳气凝胶比表面积约为570 m2/g,活化之后的比表面积高达3 500 m2/g左右。     

三聚氰胺-甲醛气凝胶模板的结构与热稳定性

采用溶胶-凝胶法合成出三聚氰胺-甲醛（MF）有机气凝胶,并通过N2吸附、红外光谱以及热重-质谱联用等实验技术对该气凝胶的多孔形态、结构特性和热稳定性进行了表征。结果表明:MF气凝胶是一种连续的、相互贯通的3维多孔网络结构材料,比表面积约842 m2/g,平均孔径为16 nm左右;热解产生了NO, H2O, NH3, NO2, CO2和CH4气体,很好地诠释了各阶段失重,其总失重高达97%,有望作为制备3维nm级多孔材料的模板。     

镍掺杂三聚氰胺-甲醛气凝胶的浸渍-还原法制备

以PdCl2为活化敏化液,水合肼为还原剂,采用化学浸渍-还原法在常温下制得了磁性金属Ni掺杂三聚氰胺-甲醛(MF)气凝胶,为金属掺杂气凝胶的制备寻得了新的途径。利用X-射线粉末衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)等对Ni掺杂MF气凝胶进行表征,SEM和TEM均表明,经浸渍-还原处理后的MF气凝胶骨架中较均匀地分布着粒径约100nm的金属Ni颗粒,其中部分颗粒生长连结形成较大团簇。N2吸-脱附实验数据显示,掺入金属Ni后,MF气凝胶的比表面积、总孔体积、微孔体积均减小,表明浸渍-还原处理后得到的金属Ni颗粒均匀分布于MF气凝胶孔隙中,其中少量大孔的出现是由形成团簇的Ni颗粒填充了部分纯MF气凝胶的孔隙撑开了孔隙结构所致。     

Preparation of mesoporous poly (acrylic acid)/SiO2 composite nanofiber membranes having adsorption capacity for indigo carmine dye

Mesoporous poly (acrylic acid)/SiO₂ (PAA/SiO₂) composite nanofiber membranes functionalized with mercapto groups were fabricated by a sol-gel electrospinning method, and their adsorption capacity for indigo carmine was investigated. The membranes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, x-ray powder diffraction (XRD), and nitrogen adsorption–desorption measurement. SEM and TEM observation results showed that the PAA/SiO₂ fibers had diameters between 400–800 nm and mesopores with an average pore size of 3.88 nm. The specific surface area of the mesoporous nanofiber membranes was 514.89 m²/g. The characteristic peaks for mercapto group vibration in FTIR and Raman spectra demonstrated that the mercapto groups have been incorporated into the silica skeleton. The adsorption isotherm data of indigo carmine on the membranes fit well with Redlich–Peterson model, and the maximum adsorption capacity calculated was 523.11 mg/g. It was found that the removal rate of indigo carmine by the membranes reached a maximum of 98% in 90 min and the adsorption kinetics followed a pseudo-second-order model. The high adsorption capacity of PAA/SiO₂ nanofiber membrane makes it a promising adsorbent for indigo carmine removal from the wastewater.     

Synthesis of dimethyl carbonate from methyl carbamate and methanol catalyzed by mixed oxides from hydrotalcite-like compounds

A series of mixed oxides calcined from hydrotalcite-like compounds with different cations were prepared and their catalytic activities were studied by the synthesis of dimethyl carbonate (DMC) from methyl carbamate and methanol. Among them, ZnFe mixed oxide possessed the best catalytic ability. Furthermore, the zinc-based mixed oxides as well as the corresponding hydrotalcite-like compounds were characterized by using ICP, TGA, CO₂-TPD and N₂ adsorption/desorption techniques.     

Studies on the performances of silica aerogel electrodes for the application of supercapacitor

Silica aerogel (SiO₂ aerogel) was prepared by sol–gel method from tetraethyl orthosilicate hydrolyzation and has been characterized by scanning electron microscopy and N₂ adsorption for its surface structure, surface area, and pore-size distribution. Constant current charge–discharge technique, cyclic voltammetry, and electrochemical impedance spectrum were employed for its specific capacitance and equivalent series resistance. The results showed that the maximum specific capacitance of SiO₂ aerogel electrode in 1 M Et₄NBF₄/PC electrolyte was 62.5 F g⁻¹. In addition, the SiO₂ aerogel capacitor exhibits excellent long-term stability with no significant degradation after 500 charging and discharging cycles. Therefore, the application of high surface area SiO₂ aerogel as electrodes in supercapacitor devices is promising.     

The chemisorption of N2 on the (110) surface of iridium

The molecular chemisorption of N₂ on the reconstructed Ir(110)-(1 × 2) surface has been studied with thermal desorption mass spectrometry, XPS, UPS, AES, LEED and the co-adsorption of N₂ with hydrogen. Photoelectron spectroscopy shows molecular levels of N₂ at 8.0 (5σ + 1π) and 11.8 (4σ) eV in the valence band and at 399.2 eV with a satellite at 404.2 eV in the N(1s) region, where the binding energies are referenced to the Ir Fermi level. The kinetics of adsorption and desorption show that both precursor kinetics and interadsorbate interactions are important for this chemisorption system. Adsorption occurs with a constant probability of adsorption of unity up to saturation coverage (4.8 × 10¹⁴ cm^?2), and the thermal desorption spectra give rise to two peaks. The activation energy for desorption varies between 8.5 and 6.0 kcal mole^?1 at low and high coverages, respectively. Results of the co-adsorption of N₂ and hydrogen indicate that adsorbed N₂ resides in the missing-row troughs on the reconstructed surface. Nitrogen is displaced by hydrogen, and the most tightly bound state of hydrogen blocks virtually all N₂ adsorption. A p1g1(2 × 2) LEED pattern is associated with a saturated overlayer of adsorbed N₂ on Ir(110)-(1 × 2).     

二氧化钛纳米晶/石墨烯复合物的制备及其光催化性能 (cited: 1)

以氧化石墨和TiO₂溶胶为前驱物,结合絮凝与水热技术制备了TiO₂纳米晶/石墨烯复合物,表征了产物的结构、形貌、孔隙率、光谱吸收性质. 结果表明：TiO₂纳米晶的存在一定程度上阻止了石墨烯片层的重组,TiO₂纳米晶/石墨烯复合物较单纯TiO₂材料具有更强的吸光性能、对亚甲基蓝分子更强的吸附性能以及更高的电荷分离效率. 在紫外光和太阳光下,TiO₂纳米晶/石墨烯复合物对亚甲基蓝的光催化降解效率均高于P25和纯TiO₂.     

NH3 adsorption on Ni(110) and the production of the NH2 species by electron irradiation

The adsorption of NH₃ on Ni(110) has been examined using electron stimulated desorption ion angular distribution (ESDIAD), low energy electron diffraction (LEED) and thermal desorption spectrometry (TDS). At ～ 85 K the NH₃ molecule enters into a series of chemisorption and physisorption states whose structures have been partially characterized by means of ESDIAD and LEED. Upon heating, these NH₃ states desorb without dissociation; for adsorption below 300 K there is essentially no thermal decomposition. The ammonia adiayer was found to be extremely sensitive to electron irradiation effects. Evidence was found to support the irradiation induced conversion of NH₃(ads) to an amido intermediate, nh_2(ads). The NH₂ adsorbs with its C_2v axis normal to the surface and its NH bonds aligned along the [001] and [001?] directions. In the absence of further electron irradiation the nh_2(ads) species is stable to 375 K whereupon it dissociates to N_(ads)and H_2(g). The remaining N_(ads) desorbs near 750 K with significant attractive N…N interaction. No evidence is found for an imido intermediate, nh_(ads). nh_2(ads) also undergoes a disproportionation/recombination reaction upon heating to produce an additional NH₃ desorption state. A significant isotope effect for NH versus ND scission, sensitive to the adsorption state of the ammonia, is found to occur upon electron irradiation.     

One-pot synthesis of hybrid nanospheres with multistructure for selective adsorption of Hg<Superscript>2+</Superscript>

Novel complex nanospheres with core/shell structure for selective adsorption of Hg²⁺ have been prepared by a simple one-pot method. Scanning electron microscopy (SEM) and transmission electron microscope (TEM) images showed the nanospheres had perpendicularly thiol-functionalized mesoporous SiO₂ hybrid shell and Fe₃O₄@SiO₂ core (Fe₃O₄@nSiO₂@mSiO₂–SH). XRD patterns of as-synthesized nanospheres confirmed the observation of the SEM and TEM. The size of the nanospheres is about 100 nm. Based on the analysis of N₂ sorption–desorption isotherm, the surface area and pore volume of the adsorbent are 861 m²/g and 0.48 cm³/g, respectively. The saturation magnetization value for Fe₃O₄@nSiO₂@mSiO₂–SH is as high as 6.87 emu g⁻¹. The nanospheres showed more accessible active sites and high dispersibility in water, exhibited excellent performance for selective Hg²⁺ adsorption, had a stable structure, and could be recycled easily with magnet.     

Functionalized SBA-15 materials for bilirubin adsorption

To investigate the driving force for bilirubin adsorption on mesoporous materials, a comparative study was carried out between pure siliceous SBA-15 and three functionalized SBA-15 mesoporous materials: CH₃-SBA-15 (MS), NH₂-SBA-15 (AS), and CH₃/NH₂-SBA-15 (AMS) that were synthesized by one-pot method. The obtained materials exhibited large surface areas (553-810 m²/g) and pore size (6.6-7.1 nm) demonstrated by XRD and N₂-ad/desorption analysis. The SEM images showed that the materials had similar fiberlike morphology. The functionalization extent was calculated according to ²⁹Si MAS NMR spectra and it was close to the designed value (10%). The synthesized mesoporous materials were used as bilirubin adsorbents and showed higher bilirubin adsorption capacities than the commercial active carbon. The adsorption capacities of amine functionalized samples AMS and AS were larger than those of pure siliceous SBA-15 and MS, indicating that electrostatic interaction was the dominant driving force for bilirubin adsorption on mesoporous materials. Increasing the ionic strength of bilirubin solution by adding NaCl would decrease the bilirubin adsorption capacity of mesoporous material, which further demonstrated that the electrostatic interaction was the dominant driving force for bilirubin adsorption. In addition, the hydrophobic interaction provided by methyl groups could promote the bilirubin adsorption.     

One-step synthesis of Fe3O4@C/reduced-graphite oxide nanocomposites for high-performance lithium ion batteries

In this paper, we propose a facile one-step strategy to prepare Fe₃O₄@amorphous carbon/reduced graphite oxide nanocomposites (FCRGs) under hydrothermal conditions. A transmission electron microscopy image has shown that the as-formed Fe₃O₄ nanoparticles coated with a layer of amorphous carbon are wrapped by reduced graphite oxide (r-GO) sheets. The diameter of Fe₃O₄ nanoparticles is less than 50 nm. N₂ adsorption/desorption isotherms indicate that the specific surface area of FCRG is 31.6 m²/g with porous structure. FCRG exhibits improved cycling stability and rate performances as a potential anode material for high-performance lithium ion batteries.     

Triple point of the first monolayer of nitric oxide adsorbed on the cleavage face of magnesium bromide

This paper is the first of three articles devoted to the CO/Mo(110) chemisorption. The experimental study of adsorption and desorption kinetics was performed by several methods: thermal desorption, low energy electron diffraction and Auger electron spectroscopy. The adsorption of CO on Mo(110) presents two different states. For these two states the desorption kinetics are first order ones, the desorption energies and frequency factors have been determined (E₁ = 99 kcal mole^?1, E₂ = 50 kcal mole^?1, v₁ = 10¹⁹ s^?1, v₂, = 5 × 10¹⁰ s^?1). The dependence of sticking coefficient on surface coverage θ was investigated and was found different for the two states of adsorption. LEED shows that the adsorption is not ordered. AES investigation suggests that in the two states C and O have different positions with respect to MO atoms.