不同晶相结构和形貌TiO2负载Ru催化剂的CO选择甲烷化

用水热法得到的钛酸纳米纤维前体,通过不同后处理方法合成了多种纳米结构的TiO₂．采用N₂等温吸附和BET比表面、X射线衍射、透射电镜和能量分散X射线分析表征了TiO₂及负载Ru催化剂的微结构,包括比表面、晶相结构和形貌以及Ru纳米颗粒尺寸分布等．对负载Ru催化剂在富氢条件下CO选择甲烷化反应活性测试表明：金红石相TiO₂和TiO₂-B为载体负载的Ru催化剂比锐钛矿相TiO₂负载的Ru催化剂表现出更高的反应性能．其活性区别说明了不同晶相结构和形貌TiO₂载体与Ru纳米颗粒的相互作用存在差异．     

二氧化钛修饰的微结构聚合物光纤预制棒制备及其在光催化中应用的探索研究

首次用二氧化钛(TiO₂)纳米材料修饰的547孔微结构聚合物光纤(MPOF)二次预制棒作为阵列化微管式光催化反应器对亚甲基兰的光催化分解进行研究.将高光催化活性的P25型二氧化钛纳米粒子均匀分散在TiO₂溶胶中,对547孔微结构聚合物光纤孔洞内壁进行铺膜,得到了负载光催化剂的阵列化微管材料.该TiO₂MPOF有序复合的阵列化微管不仅对二氧化钛纳米粒子起到负载作用,还可以作为光波导介质(rolling-up薄膜波导,聚光、导光进入二氧化钛薄膜层)、污染物反应流体通道.以有机染料亚甲基兰为模拟污染物,研究了TiO₂负载量、亚甲基兰的初始浓度及溶液pH值等因素对光降解效果的影响.该反应器547个孔道的内表面用于负载光催化剂,不仅增加了固-液接触面积,也提高了光的吸收效率,从而提高了光催化效率.迄今为止,这种兼具导光、聚光、传质、负载功能于一体的光催化反应器还未见报道.     

基于薄膜电极溶胶修饰的染料敏化太阳电池光电特性研究

染料敏化太阳电池(DSC)中的纳米薄膜电极 是决定太阳电池光电转换性能的重要组成部分. 为改善薄膜电极特性, 采用了不同浓度的TiO₂溶胶对DSC光阳极导电玻 璃和纳米TiO₂多孔薄膜进行不同方式的界面处理. 利用X射线衍射方法对制备得到的多孔薄膜以及溶胶经高温处理 后致密层中纳米TiO₂颗粒的尺寸及晶型进行了测试. 采用高分辨透射电子显微镜和场发射扫描电子 显微镜观察了纳米颗粒及薄膜微结构形貌. 采用强度调制光电流谱/光电压谱分析了TiO₂溶 胶的不同处理方式对电子传输和复合的影响. 在100 mW· cm^-2光强以及暗环境下分别测试了DSC的伏安输出性能以及暗电流. 结果表明, 不同浓度和处理方式均能较好地抑制暗电流. 溶胶处理后光生电子寿命τ_n延长, 电子传输平均时间τ_d相应缩短. 采用浓度为0.10 mol·L^-1的 溶胶对导电玻璃和多孔膜同时处理, DSC的宏观输出特性最佳, 短路电流密度J_sc提高了10.9%, 光电转换效率η提高了11.9%.     

硼(氮、氟)掺杂对TiO2纳米颗粒光学性能的影响

利用X射线衍射谱、拉曼光谱和紫外-可见光吸收光谱研究了硼(氮、氟)掺杂对TiO₂纳米颗粒光学性能的影响.X射线衍射谱和拉曼光谱结果表明,掺硼(氮、氟)对TiO₂纳米颗粒的锐钛矿相晶体结构无明显影响,而其锐钛矿晶格出现畸变(c/a值增大),这被归因于掺杂原子对TiO₂纳米颗粒表面氧原子缺位沿晶格c轴方向的占据.另外,掺硼(氮、氟)TiO₂纳米颗粒吸收带红移与TiO相似文献   

铁和镧共掺杂纳米二氧化钛光催化剂的制备、表征及其光催化活性

以葡聚糖为模板,钛酸四正丁酯、硝酸铁和硝酸镧为前驱体采用模板法制备了一系列铁、镧单掺杂及共掺杂纳米TiO₂光催化剂. 利用SEM、XRD、BET比表面积测定和UV-Vis等技术对其形貌、晶体结构及表面结构、光吸收特性等进行了表征. 以甲基橙溶液的光催化降解为模型反应,考察了不同掺杂的样品在紫外和可见光下的光催化性能. TiO₂材料具有较大的比表面积(约150 m²/g),铁和镧共掺杂纳米TiO₂在可见光区域有较强的吸收,在紫外和可见光条件下较纯TiO₂和单掺杂TiO₂对甲基橙溶液具有更好的光催化降解效果,且铁和镧的掺杂量显著影响该材料的催化性能. 当铁掺杂量为0.5mol%、镧掺杂量为0.3mol%,在500 ℃焙烧2 h所得光催化材料的催化性能最佳,焙烧4 h即可使甲基橙的降解率达98.8%,且该复合材料有较高的循环回收利用率,重复使用4次仍可使甲基橙的降解率保持在88%以上.     

5(6)羧基荧光素敏化TiO2纳米粒子的光致电子转移的荧光特性研究

通过水解TiCl₄制备了锐钛矿结构TiO₂纳米粒子, 并用时间分辨荧光光谱研究了5(6)CFL(5(6)-Carboxyfluorescein, 简称5(6)CFL)染料敏化TiO₂纳米粒子体系的光致电子转移动力学. 5(6)CFL染料敏化TiO₂纳米粒子能形成电荷转移复合物, 这归因于染料分子的激发电子态波函数Ψ(D^*)与电荷分离态波函数Ψ(D⁺ +e^-)之间的耦合作用. 当激发5(6)CFL染料敏化TiO₂纳米粒子体系时, 电子以两种不同方式注入TiO₂纳米粒子导带: 第一, 通过5(6)CFL染料分子的激发态注入; 第二, 从电荷转移复合物(5(6)CFL/TiO₂)直接注入. 时间分辨荧光光谱表明, 在水溶液中纯5(6)CFL染料的荧光以寿命为τ₁=41 ps (74.4%) 和τ₂=3.22 ns (25.6%) 的双e指数衰减, 而5(6)CFL染料敏化TiO₂纳米粒子体系的荧光分别以时间常数为τ₁=44 ps (90.4%), τ₂=478 ps (8.6%) 和τ₃=2.41 ns (1.0%) 的三e指数衰减. 本文的研究工作能够为染料敏化太阳能电池的光致电子转移机理提供有价值的参考.     

光沉积Ru和RuO2的锐钛矿TiO2纳米片的光解水产氧

采用水热法以HF作为结构调控剂合成了主要暴露（001）面的锐钛矿TiO₂纳米片,通过光沉积方法分别合成了负载Ru和RuO₂物种的光催化剂。利用X射线衍射、透射电镜和氢气程序升温还原等分析表征了催化剂的结构性质。通过光解水产氧反应来研究催化剂的催化性能,详细考察了Ru含量、负载方式以及氧化和还原处理等因素的影响,光解水产氧速率的差异证明了Ru物种在不同晶面的电荷-空穴分离效应。与负载单一助催化剂的Ru/TiO₂和RuO₂/TiO₂样品相比,活性最优的0.5%Ru-1.0%RuO₂/TiO₂样品由于负载了双助催化剂,其催化活性得到更大的提高,证实了在锐钛矿TiO₂上的晶面电荷-空穴分离效应.     

多孔TiO2/Al/SiO2纳米复合结构的紫外光吸收特性研究

在SiO₂玻璃衬底上用脉冲激光沉积(PLD)技术，分别沉积Ti和Ti/Al膜，经电化学阳极氧化成功制备了多孔TiO₂/SiO₂和TiO₂/Al/SiO₂纳米复合结构. 其中TiO₂薄膜上的微孔阵列高度有序，分布均匀. 实验研究了Al过渡层对多孔TiO₂薄膜光吸收特性的影响. 结果表明：无Al过渡层的多孔TiO₂薄膜其紫外吸收峰在27     

氮掺杂TiO2的冲击合成及可见光催化活性研究

 冲击相变及冲击诱导化学反应可导致材料的物理、化学性能发生显著改变。采用炸药爆轰驱动飞片高速碰撞产生冲击波的方法,对富氮掺杂物双氰胺（C₂N₄H₄）与P25 TiO₂或偏钛酸（H₂TiO₃）的粉末混合物进行冲击加载,对回收产物进行X射线粉末衍射、透射电子显微镜、X光电子能谱、比表面积及紫外-可见漫反射光谱表征,通过亚甲基蓝和罗丹明B评价了回收产物的可见光催化降解活性。结果表明：以P25 TiO₂为原料的冲击氮掺杂浓度可达8.88%,掺杂样品具有明显的可见光吸收,能带宽度减小到1.75 eV,样品中形成了少量Srilankite高压相;而以偏钛酸为原料的冲击氮掺杂浓度为3%～4%,能带宽度变化较小,但是由于其独特的冲击脱水膨胀机理,比表面积剧增。冲击氮掺杂样品对亚甲基蓝和罗丹明B染料有较好的吸附和可见光催化降解作用,其中高飞片速度处理的样品有更高的光催化降解活性。     

多种金属/TiO2核壳纳米棒阵列的通用制备方法

使用了一种具有较大通用性的方法制备了金属/二氧化钛(TiO₂)核壳纳米结构. 采用电沉积方法在多孔氧化铝模板(AAO)孔洞中沉积壁厚均一的TiO₂纳米管,TiO₂纳米管的壁厚可以通过沉积时间来控制,而纳米管的直径和长度则由模板孔洞大小和模板厚度决定. 采用这种方法制备的TiO₂纳米管顶端是开放的,而底端连接在电沉积前溅射在AAO模板背面的金膜上. 这种TiO₂纳米管阵列结构适合进行二次电沉积,以它为模板将Pd、Cu、Fe等金属沉积到纳米管中形成核壳纳米棒结构. 这是一种可以用于制备多种金属/TiO₂核壳纳米结构的通用方法,采用这种方法制备的金属/TiO₂核壳纳米棒结构具有填充率高和取向性好的特点,而且它们的壁厚和长度可以通过分别改变两步电沉积的时间来控制.     

Bi2MoO6纳米片/TiO2纳米棒阵列复合材料的制备及其可见光响应光电催化性能研究

Novel Bi₂MoO₆/TiO₂ heterojunction was fabricated by growing Bi₂MoO₆ nanosheets arrays on the vertically aligned TiO₂ nanorods arrays via a two-step solvothermal method. The obtained Bi₂MoO₆/TiO₂ hierarchical heterojunction showed excellent visible light photoelectrochemical performance. Compared with the pure TiO₂ and Bi₂MoO₆, the photocurrent density of the heterojunction was increased 57 and 29 times, respectively. Furthermore, the hydrogen generation rate of the Bi₂MoO₆/TiO₂ for photoelectrocatalytic water-splitting was about 6 times higher than that of the pure Bi₂MoO₆. The improved performance can be attributed to the synergistic effects of enhanced absorption of visible light, increase of migration rate and separation efficiency of photo-induced carriers.     

银/二氧化钛核壳纳米颗粒对碲化镉纳米晶的荧光增强研究

利用新合成的复合纳米结构银/二氧化钛核壳纳米颗粒,研究了金属银纳米颗粒对碲化镉纳米晶层荧光的增强情况.结果表明,这种新型复合金属纳米结构能极大地增强发光纳米晶层的荧光强度.银/二氧化钛核壳纳米颗粒是以水合肼、硝酸银和四异丙氧基钛为原材料,利用胶体化学法在水溶液中合成.透射电子显微镜图片表明这种新合成的银/二氧化钛纳米材料基本上呈球形,有较为明显的核壳结构,中间黑色的核是银纳米颗粒,外层颜色较浅部分是二氧化钛壳层.另外,包裹二氧化钛壳层后,银纳米颗粒的表面等离子吸收带从409 nm红移至430 nm,也证实了这种新型核壳纳米材料的形成.将此合成方法得到的银/二氧化钛纳米颗粒和碲化镉纳米晶用旋转涂覆方法进行直接组合后,得到了银纳米颗粒对碲化镉纳米晶荧光的明显增强,并对其增强的物理过程进行了讨论.这种能够增强荧光团发光的新型复合银纳米结构将在发光器件、荧光成像、生物探测等方面具有一定的应用价值.     

Dye-sensitized solar cells based on ZnO nanowire array/TiO2 nanoparticle composite photoelectrodes with controllable nanowire aspect ratio

The ZnO nanowire (NW) array/TiO₂ nanoparticle (NP) composite photoelectrode with controllable NW aspect ratio has been grown from aqueous solutions for the fabrication of dye-sensitized solar cells (DSSCs), which combines the advantages of the rapid electron transport in ZnO NW array and the high surface area of TiO₂ NPs. The results indicate that the composite photoelectrode achieves higher overall photoelectrical conversion efficiency (η) than the ZnO NW alone. As a result, DSSCs based on the ZnO NW array/TiO₂ NP composite photoelectrodes get the enhanced photoelectrical conversion efficiency, and the highest η is also achieved by rational tuning the aspect ratio of ZnO NWs. With the proper aspect ratio (ca. 6) of ZnO NW, the ZnO NW array/TiO₂ NP composite DSSC exhibits the highest conversion efficiency (5.5 %). It is elucidated by the dye adsorption amount and interfacial electron transport of DSSCs with the ZnO NW array/TiO₂ NP composite photoelectrode, which is quantitatively characterized using the UV-Vis absorption spectra and electrochemical impedance spectra. It is evident that the DSSC with the proper aspect ratio of ZnO NW displays the high dye adsorption amount and fastest interfacial electron transfer.     

Methylene blue photoelectrodegradation under UV irradiation on Au/Pd-modified TiO2 films

In this work TiO₂ thin films were modified with gold/palladium (Au/Pd) bimetallic paticles by sputtering method. TiO₂ films were deposited on ITO (SnO₂:In) by Doctor Blade method and post-anneling. The properties of the films were studied through measurements of XRD (X-ray diffraction) and AFM (atomic force microscopy). The degradation of methylene blue was studied by UV-irradiated pure TiO₂ and Au/Pd-modified TiO₂ in aqueous solution. Langmuir-Hinshelwood model was used to obtain kinetic information. Photocatalytic study indicated that Au/Pd-modified TiO₂ photocatalytic activity was better than TiO₂ pure; the best half-life time for Au/Pd-modified TiO₂ in photodegradation was 2.8 times smaller than TiO₂ pure; finally the efficiency in methylene blue photodegradation was improved from 23% to 43% when Au/Pd-modified TiO₂ films were used.     

Preparation and characterization of amine-functionalized SiO2/TiO2 films for formaldehyde degradation

This paper investigated the gaseous formaldehyde degradation by the amine-functionalized SiO₂/TiO₂ photocatalytic films for improving indoor air quality. The films were synthesized via the co-condensation reaction of methyltrimethoxysilane (MTMOS) and 3-aminopropyltrimethoxysilane (APTMS). The physicochemical properties of prepared photocatalysts were characterized with N₂ adsorption/desorption isotherms measurement, X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FT/IR). The effect of amine-functional groups and the ratio of MTMOS/APTMS precursors on the formaldehyde adsorption and photocatalytic degradation were investigated. The results showed that the formaldehyde adsorption and photocatalytic degradation of the APTMS-functionalized SiO₂/TiO₂ film was higher than that of SiO₂/TiO₂ film due to the surface adsorption on amine sites and the relatively high of the specific surface area of the APTMS-functionalized SiO₂/TiO₂ film (15 times higher than SiO₂/TiO₂). The enhancement of the formaldehyde degradation of the film can be attributed to the synergetic effect of adsorption and subsequent photocatalytic decomposition. The repeatability of photocatalytic film was also tested and the degradation efficiency was 91.0% of initial efficiency after seven cycles.     

Synthesis, structure and optical properties of Eu/TiO2 nanocrystals at room temperature

The nanocrystal samples of titanium dioxide doped with europium ion (Eu³⁺/TiO₂ nanocrystal) are synthesized by the sol-gel method with hydrothermal treatment. The Eu³⁺ contents (molar ratio) in the samples are 0, 0.5%, 1%, 2%, 3% and 4%. The X-ray diffraction, UV-Vis spectroscopy data and scanning electron microscope image show that crystallite size is reduced by the doping of Eu³⁺ into TiO₂. Comparing the Raman spectra of TiO₂ with Eu³⁺/TiO₂ (molar ratio Eu³⁺/TiO₂=1%, 2% and 4%) nanocrystals at different annealing temperatures indicates that the anatase-to-rutile phase transformation temperatures of Eu³⁺/TiO₂ nanocrystals are higher than that of TiO₂. This is due to the formation of Eu-O-Ti bonds on the surface of the TiO₂ crystallite, as characterized by the X-ray photoelectron spectroscopy. The photoluminescence spectra of TiO₂ in Eu³⁺/TiO₂ nanocrystals are interpreted by the surface self-trapped and defect-trapped exciton relaxation. The photoluminescence of Eu³⁺ in Eu³⁺/TiO₂ nanocrystals has the strongest emission intensity at 2% of Eu³⁺ concentration.     

Hydrothermal synthesis of flower-like TiO2 nanocrystals/graphene oxide nanocomposites

A facile hydrothermal method has been developed to be capable of decorating graphene oxide (GO) with flower-like TiO₂ nanocrystals without using any bridging species. The flower-like TiO₂ nanocrystals were uniformly self-assembled on the surface of GO nanosheets. The photocatalytic activity experiment indicated that the prepared TiO₂/GO nanocomposites exhibited a higher photocatalytic activity for the photocatalytic degradation of rhodamine B (RB) aqueous solution under the UV illumination, this methodology made the synthesis of TiO₂/GO nanocomposites possible and may be further extended to prepare more complicated nanocomposites based on GO for technological applications.     

One-step solvothermal preparation of TiO2/C composites and their visible-light photocatalytic activities

Preparation of anatase type titania nanoparticles and their carbon modification were synchronously achieved by the solvothermal method with glycerol as the carbon source. The as-prepared samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and diffuse reflectance spectra (DRS). It was found that the glycerol/ethanol ratio affected significantly the morphology and properties of TiO₂/C composites. The TiO₂/C composite which was obtained in the solution with the glycerol/ethanol ratio of 5/75, contained 1.2 mass% carbon and exhibited both superior adsorption capability and visible-light photocatalytic activity. Contrary to this, samples prepared in the solution with higher glycerol/ethanol ratio, exhibited lower photocatalytic activity similar to that of the titania without carbon modification. It was suggested that excess addition of glycerol might contribute to large amounts of carbonaceous species and severe aggregation of the as-prepared samples, and thus reduced the surface area. As a result, the adsorption capability and visible-light photocatalytic activity increased at first and then decreased with the increase of glycerol addition. Present study provided a facile one-step method to obtain TiO₂/C composites with a controllable carbon content and photocatalytic performance under mild temperature.     

Structure and photoluminescence properties of Er3+-doped TiO2-SiO2 powders prepared by sol-gel method

Er 3+-doped TiO 2-SiO 2 powders are prepared by the sol-gel method,and they are characterized by high resolution transmission electron microscopy (HR-TEM),X-ray diffraction (XRD) spectra,and Raman spectra of the samples.It is shown that the TiO 2 nanocrystals are surrounded by an SiO 2 glass matrix.The photoluminescence (PL) spectra are recorded at room temperature.A strong green luminescence and less intense red emission are observed in the samples when they are excited at 325 nm.The intensity of the emission,which is related to the defect states,is strongest at the annealing temperature of 800 C.The PL intensity of Er 3+ ions increases with increasing Ti/Si ratio due to energy transfer between nano-TiO 2 particles and Er 3+ ions.