High-quality CdS quantum dots sensitized ZnO nanotube array films for superior photoelectrochemical performance

The surface characteristics of ZnO were synthetically optimized by a self-designed simultaneous etching and W-doping hydrothermal method utilizing as-prepared ZnO nanorod (NR) array films as the template. Benefiting from the etching and regrowth process and the different structural stabilities of the various faces of ZnO NRs, the uniquely etched and W-doped ZnO (EWZ) nanotube (NT) array films with larger surface area, more active sites and better energy band structure were used to improve the photoelectrochemical (PEC) performance and the loading quality of CdS quantum dots (QDs). On the basis of their better surface characteristics, the CdS QDs were uniformly loaded on EWZ NT array film with a good coverage ratio and interface connection; this effectively improved the light-harvesting ability, charge transportation and separation as well as charge injection efficiency during the PEC reaction. Therefore, all the CdS QD-sensitized EWZ NT array films exhibited significantly enhanced PEC performance. The CdS/EWZ-7 composite films exhibited the optimal photocurrent density with a value of 12 mA· cm^-2, 2.5 times higher than that of conventional CdS/ZnO-7 composite films under the same sensitization times with CdS QDs. The corresponding etching and optimizing mechanisms were also discussed.     

流延法制备高锂离子电导Li_(1.4)Al_(0.4)Ti_(1.6)(PO_4)_3固态电解质及其环氧树脂改性

以溶胶凝胶法合成的高纯Li_(1.4)Al_(0.4)Ti_(1.6)(PO_4)_3(LATP)纳米晶体粉末为原料,通过流延法成膜,在950℃下煅烧5 h合成LATP固态电解质片;对其进行环氧树脂改性后,能量色散X射线光谱元素图像表明环氧树脂完全浸入LATP内部,可以有效防止水渗透.研究发现流延法合成的LATP固态电解质在25℃?C时电导率高达8.70×10~(-4)S·cm~(-1)、活化能为0.36 eV、相对密度为89.5%.经过环氧树脂改性后电导率仍高达3.35×10-4S·cm-1、活化能为0.34 e V、相对密度为93.0%.高电导隔水的环氧树脂改性LATP固态电解质可作为锂金属保护薄膜用于新型高比容量电池.     

胆甾液晶掺杂活性层对有机太阳能电池性能的影响

以poly(3-hexylthiophene)(P3HT)为电子给体,indene-C60bisadduct(ICBA)为电子受体,通过掺杂不同浓度胆甾液晶氯化胆甾醇制备了有机体异质结太阳能电池.结果表明,适当浓度掺杂使器件的开路电压提高到了0.78 V,但短路电流密度却有所降低,填充因子几乎不变,能量转换效率提高了10%.利用X射线、光致发光、原子力显微镜及紫外-可见吸收光谱进行表征,发现液晶掺杂对活性层的结晶度、分子内部排列情况、薄膜表面形貌和光吸收特性等都有明显影响.     

铟锡氧化物薄膜表面等离子体损耗降低的研究

本文采用直流磁控溅射方法在普通浮法玻璃基底上制备了立方多晶铁锰矿结构的铟锡氧化物(indium tin oxide, ITO)薄膜,并对其进行了结晶性、表面粗糙度、紫外-可见吸收光谱、折射率、介电常数及霍尔效应的测试.研究了溅射时基底温度的改变对于ITO薄膜的光电、表面等离子体性质的影响.随着基底温度由100?C升高至500?C,其光学带隙(3.64—3.97eV)展宽,减少了电子带间跃迁的概率,有效降低了ITO薄膜的光学损耗.与此同时,对应ITO薄膜的载流子浓度(4.1×10~(20)-—2.48×10~(21)cm~(-3))与迁移率(24.6—32.2 cm~2·V~(-1)·s~(-1))得到提高,电学损耗明显降低.     

衬底温度对ZnO薄膜的结构和光学特性的影响

利用等离子体辅助分子束外延(P-MBE)设备在蓝宝石衬底上通过改变生长温度,制备了不同的ZnO样品.研究了衬底温度对ZnO的结构、光学和电学性质的影响.样品的晶体结构利用X射线衍射谱进行表征.X射线衍射谱表明,所有的ZnO样品都是(002)取向的六角纤锌矿结构.随着生长温度的升高,X射线的(002)衍射峰的半峰全宽逐渐...     

Investigation of reduced graphene oxide effects on ultra-violet detection of ZnO thin film

The reduced graphene oxide (rGO) incorporated ZnO thin films were fabricated by dip-coating method. The Raman and FT-IR spectra of 0.075 wt% incorporated composite film showed reduction of GO in composite film. The transmittanceProd. Type: FTP spectra have shown that rGO incorporation increase the visible light absorption of ZnO thin film while the calculated band gaps of samples were decreased from 3.28 to 3.25 eV by increasing the rGO content. The linear trend of I–V curve suggests an ohmic contact between ZnO and rGO. Besides, it was found that by increasing the rGO content, the electrical resistivity was decreased from 4.32×10² Ω cm for pure ZnO film to 2.4×10¹ Ω cm for 0.225 wt% rGO incorporated composite film. The composite photodetectors not only possessed a desirable UV photosensitivity, but also the response time of optimum sample containing 0.075 wt% rGO was reduced to about one-half of pure ZnO thin film. Also, the calculated signal to noise (SNR) showed that highly conductive rGO in composite thin films facilitate the carrier transportation by removing the trapping centers. The mechanism of photoresponsivity improvement of composite thin films was proposed by carrier transportation process.     

镧掺杂BaSnO3薄膜的电学和光学特性

利用射频磁控溅射法在(LaAlO₃)_0.3(SrAl_0.5Ta_0.5O₃)_0.7 (001)单晶基底上生长了镧掺杂BaSnO₃外延薄膜. 通过Hall效应和热电势测量证实了镧掺杂BaSnO₃薄膜具有n型简并半导体特征, 并且基于载流子浓度和Seebeck系数计算出电子的有效质量为0.31m₀ (m₀为自由电子质量). 镧掺杂BaSnO₃薄膜在可见波段具有良好的透明性(透过率大于73%). 基于介电模型对薄膜的透过率曲线进行拟合, 从拟合结果中不仅得到了薄膜的厚度为781.2 nm, 能带宽度为3.43 eV、 带尾宽度为0.27 eV和复光学介电常数随波长的变化规律, 而且也强力地支持了基于电学参数计算电子有效质量的正确性.     

过渡金属与F共掺杂ZnO薄膜结构及磁、光特性

采用溶胶-凝胶法在玻璃衬底上制备了过渡金属元素与F共掺杂Zn_0.98-xTM_xF_0.02O (TM_x=Cu_0.02, Ni_0.01, Mn_0.05, Fe_0.02, Co_0.05)薄膜, 进而利用X射线衍射仪、扫描电子显微镜、紫外-可见透过谱、光致发光及振动样品磁强计等研究了薄膜的表面形貌、微结构、禁带宽度及光致发光(PL)和室温磁学特性. 研究表明: 掺杂离子都以替位的方式进入了ZnO晶格, 掺杂不会破坏ZnO的纤锌矿结构. 其中Zn_0.93Co_0.05F_0.02O薄膜样品的颗粒尺寸最大, 薄膜的结晶度最好且c轴择优取向明显; Zn_0.93Mn_0.05F_0.02O薄膜样品的颗粒尺寸最小, 薄膜结晶度最差且无明显的c轴择优取; Cu, Ni, Fe与F共掺杂样品的颗粒尺寸大小几乎相同. TM掺杂样品均表现出很高的透过率, 同时掺杂后的薄膜样品的禁带宽度都有不同程度的红移. PL谱观察到Zn_0.98-xTM_xF_0.02O薄膜的发射峰主要由较强的紫外发射峰和较弱的蓝光发射峰组成. Zn_0.93Mn_0.05F_0.02O薄膜样品的紫外发光峰最弱, 蓝光发射最强, 饱和磁化强度最大; 与之相反的是Zn_0.96Cu_0.02F_0.02O薄膜, 其紫外发光峰最强, 蓝光发射最弱, 饱和磁化强度最小. 结合微结构和光学性质对Zn_0.98-xTM_xF_0.02O薄膜的磁学性质进行了讨论.     

Oxygen vacancies and V co-doped Co_3O_4 prepared by ion implantation boosts oxygen evolution catalysis

Introducing heteroatoms and defects is a significant strategy to improve oxygen evolution reaction(OER) performance of electrocatalysts. However, the synergistic interaction of the heteroatom and defect still needs further investigations. Herein, we demonstrated an oxygen vacancy-rich vanadium-doped Co_3O_4(V–O_v–Co_3O_4), fabricated by V-ion implantation, could be used for high-efficient OER catalysis. X-ray photoelectron spectra(XPS) and density functional theory(DFT) calculations show that the charge density of Co atom increased, and the reaction barrier of reaction pathway from O*to HOO*decreased. V–O_v–Co_3O_4 catalyst shows a low overpotential of 329 mV to maintain current density of 10 m A·cm~(-2), and a small Tafel slope of 74.5 m V·dec~(-1). This modification provides us with valuable perception for future design of heteroatom-doped and defect-based electrocatalysts.     

不同生长条件下ZnO薄膜电学性质的研究

ZnO薄膜中的高的背景电子浓度能够对p型掺杂形成补偿,从而对p型掺杂造成障碍,了解高背景电子浓度的来源有助于对p型掺杂的研究。本文采用分子束外延技术在不同真空度下在a面蓝宝石衬底上生长了一系列氧化锌薄膜,发现在低真空度下生长的样品的载流子浓度较高,为10¹⁹ cm^-3量级;而高真空度下生长的样品,其载流子浓度比低真空生长的样品显著降低,降低了3个数量级。在相同条件下生长的样品,通过不同的后处理手段进行处理后,其电子浓度未发生明显变化,说明氧空位等本征缺陷不是ZnO薄膜中电子的主要来源,高背景电子浓度应该与生长过程中非故意引入的杂质相关。通过低温光致发光表征,发现低真空度下生长的样品在低温下3.366 eV处有强的施主束缚激子发光峰,而高真空度下生长的样品的此发光峰显著变弱。由此,高电子浓度被归结为与生长过程中非故意引入的氢杂质相关。     

Observation of positive and small electron affinity of Si-doped AlN films grown by metalorganic chemical vapor deposition on n-type 6H–SiC

We have investigated the electron affinity of Si-doped AlN films(N_(Si)= 1.0 × 10~(18)–1.0 × 10_(19)cm~(-3)) with thicknesses of 50, 200, and 400 nm, synthesized by metalorganic chemical vapor deposition(MOCVD) under low pressure on the ntype(001)6H–SiC substrates. The positive and small electron affinity of AlN films was observed through the ultraviolet photoelectron spectroscopy(UPS) analysis, where an increase in electron affinity appears with the thickness of AlN films increasing, i.e., 0.36 eV for the 50-nm-thick one, 0.58 eV for the 200-nm-thick one, and 0.97 e V for the 400-nm-thick one.Accompanying the x-ray photoelectron spectroscopy(XPS) analysis on the surface contaminations, it suggests that the difference of electron affinity between our three samples may result from the discrepancy of surface impurity contaminations.     

通过交替生长气氛调控N掺杂ZnO薄膜电学特性

使用分子束外延方法在c面蓝宝石衬底上生长了系列氮掺杂ZnO薄膜样品。在连续的富锌气氛环境中生长的样品,由于存在大量的施主缺陷,呈现n型电导。为了抑制施主缺陷带来的补偿效应,在生长过程中,通过周期性补充氧气,形成周期性的富氧气氛,缓解了氮掺杂浓度和施主缺陷浓度之间的矛盾。光致发光测量表明,通过交替生长气氛,氧空位和锌间隙等缺陷在薄膜中得到了显著抑制。通过交替生长气氛生长的外延薄膜的结晶质量也有所提高。样品显示出重复性较高的p型电导,载流子浓度可达到10¹⁶ cm^-3。周期性补氧调节生长气氛的生长方式是一种有效实现p型掺杂ZnO的方法。     

阴极电沉积ZnO薄膜的取向控制生长

采用阴极电沉积法,在Zn(NO3)2水溶液中,以304不锈钢为衬底制备了ZnO薄膜,研究了Zn2+浓度和电流密度对ZnO薄膜择优取向的影响规律。XRD结果表明:随着Zn2+浓度和电流密度增大,ZnO薄膜逐渐由(002)面择优取向生长转变为(101)面择优取向生长;当Zn2+浓度为0.005mol.L-1、电流密度为2.0mA.cm-2或Zn2+浓度为0.05mol.L-1、电流密度为0.5mA.cm-2时,可以得到(002)面择优取向生长的ZnO薄膜;当Zn2+浓度为0.05mol.L-1、电流密度为2.0mA.cm-2时,可以得到(101)面择优取向生长的ZnO薄膜。根据二维晶核理论,通过分析不同生长条件下的过饱和度及其对ZnO的(002)型和(101)型二维晶核形核活化能的影响,对这一规律进行了解释。可见,通过改变Zn2+浓度和电流密度能够实现阴极电沉积ZnO薄膜的取向可控生长。     

A two-component model for the electron distribution function in ahigh-current pseudospark or back-lighted thyratron

Temperature, energy, and densities of two electron distribution function components, including an isotropic bulk part and an anisotropic beam, are analyzed for a hydrogen pseudospark and/or back-lighted thyratron switch plasma with a peak electron density of 1-3×10¹⁵ cm^-3 and peak current density of ≈10⁴ A/cm². Estimates of a very small cathode-fall width during the conduction phase and high electric field strengths lead to the injection of an electron beam with energies ⩾100 eV and density of 10¹³-10¹⁴ cm^-3 into a Maxwellian bulk plasma. Collisional and radiative processes of monoenergetic beam electrons, bulk plasma electrons and ions, and atomic hydrogen are modeled by a set of rate equations, and line intensity ratios are compared with measurements. Under these high-current conditions, for an initial density n_H2=10¹⁶ cm^-3 and electron temperature of 0.8-1 eV, the estimated beam density is ≈10¹³ -10¹⁴ cm^-3. These results suggest the possibility of producing in a simple way a very high-density electron beam     

Influence of oxygen pressure of ZnO/glass substrate produced by pulsed filtered cathodic vacuum arc deposition

The effects of oxygen pressure on the structural and optical properties of high quality transparent conductive ZnO thin films were studied in detail. ZnO thin films were prepared by pulsed filtered cathodic vacuum arc deposition system under various oxygen pressures on glass substrate at room temperature. With increasing oxygen pressure, the structure and optical properties of films change. The structural and optical properties of the ZnO thin films were investigated using X-ray diffraction, transmittance spectrometry, refractive index, oscillator parameters, energy band gap and Urbach tail. The films show c-axis oriented (0 0 2) hexagonal wurtize crystal structure. It has been found that the grain size of ZnO thin films increases from 16.9 to 22.6 nm with the increase of oxygen pressure from 3.8×10⁻⁴ to 6.9×10⁻⁴ Torr and the crystallinity is enhanced. Average transmittance is about 90% in the visible region of the ZnO thin films. From optical transmittance spectra of ZnO films, the absorption edge shifts towards the taller wavelength with an increase in oxygen pressure. The energy band gap decreases from 3.31 to 3.20 eV with an increase in oxygen pressure. The packing density investigation shows in ZnO films high packing densities (above 0.78) can be obtained.     

MgxZn1-xO合金制备及MgZnO/ZnO异质结构的光学性质

利用射频等离子体辅助的分子束外延(P-MBE)技术在c面的蓝宝石衬底上生长了具有不同Mg含量(0≤x≤0.28)的六方相MgZnO合金薄膜,研究了该系列样品Raman频移的幅度与合金组分的对应关系,为MgZnO合金中Mg含量的确定提供了新的方法。在此基础上选择具有合适带宽的MgZnO合金作为垒层,制备了MgZnO/ZnO量子阱结构。在较高的光激发密度下,观测到了发光强度随激发密度的超线性增加,并将之归因于激子-激子碰撞引起的超辐射过程。     

Optoelectronic properties of SnO_2 thin films sprayed at different deposition times

This article presents the elaboration of tin oxide(SnO_2) thin films on glass substrates by using a home-made spray pyrolysis system. Effects of film thickness on the structural, optical, and electrical film properties are investigated. The films are characterized by several techniques such as x-ray diffraction(XRD), atomic force microscopy(AFM), ultravioletvisible(UV–Vis) transmission, and four-probe point measurements, and the results suggest that the prepared films are uniform and well adherent to the substrates. X-ray diffraction(XRD) patterns show that SnO_2 film is of polycrystal with cassiterite tetragonal crystal structure and a preferential orientation along the(110) plane. The calculated grain sizes are in a range from 32.93 nm to 56.88 nm. Optical transmittance spectra of the films show that their high transparency average transmittances are greater than 65% in the visible region. The optical gaps of SnO_2 thin films are found to be in a range of 3.64 e V–3.94 e V. Figures of merit for SnO_2 thin films reveal that their maximum value is about 1.15 × 10-4-1?atλ = 550 nm. Moreover, the measured electrical resistivity at room temperature is on the order of 10-2?·cm.     

Synthesis and thermoelectric properties of Bi-doped SnSe thin films

Bi doped n-type SnSe thin films were prepared by chemical vapor deposition (CVD) and their structure and thermoelectric properties were studied. The x-ray diffraction patterns, x-ray photoelectron spectroscopy, and microscopic images show that the prepared SnSe thin films were composed of pure SnSe crystals. The Seebeck coefficients of the Bi-doped SnSe were greatly improved compared to that of undoped SnSe thin films. Specifically, Sn_0.99Bi_0.01Se thin film exhibited a Seebeck coefficient of -905.8μV·K^-1 at 600 K, much higher than 285.5 μV·K^-1 of undoped SnSe thin film. Further first-principles calculations reveal that the enhancement of the thermoelectric properties can be explained mainly by the Fermi level lifting and the carrier pockets increasing near the Fermi level due to Bi doping in the SnSe samples. Our results suggest the potentials of the Bi-doped SnSe thin films in thermoelectric applications.     

基于电场调控的高性能紫外无机-有机复合结构光电探测器

通过溶液旋涂制备了结构为ITO/ZnO/P3HT:ITIC/Ag的紫外无机-有机复合结构光电探测器,混合膜中聚合物给体(P3HT)和非富勒烯小分子受体(ITIC)的质量比为100:1.由于载流子传输通道不连续,器件在零偏压下的暗电流密度很小,为5.8×10-10 A·cm-2,为器件实现外加电场可调和光电流倍增提供了条...     

Investigation of Zn_(1-x)Cd_xO films bandgap and Zn_(1-x)Cd_xO/ZnO heterojunctions band offset by x-ray photoelectron spectroscopy

A series of Zn_(1-x)Cd_xO thin films have been fabricated on sapphire by pulsed-laser deposition(PLD), successfully. To investigate the effect of Cd concentration on structural and optical properties of Zn_(1-x)Cd_xO films, x-ray diffraction(XRD),ultraviolet-visible spectroscopy(UV-vis), and x-ray photoelectron spectroscopy(XPS) are employed to characterize the films in detail. The XRD pattern indicates that the Zn_(1-x)Cd_xO thin films have high single-orientation of the c axis. The energy bandgap values of ZnCdO thin films decrease from 3.26 eV to 2.98 eV with the increasing Cd concentration(x)according to the(αhν)~2–hν curve. Furthermore, the band offsets of Zn_(1-x)Cd_xO/ZnO heterojunctions are determinated by XPS, indicating that a type-I alignment takes place at the interface and the value of band offset could be tuned by adjusting the Cd concentration.