Influence of interstitial air holes in index-guiding photonic crystal fibers on their basic properties

The modal properties of index-guiding photonic crystal fibers (IGPCFs) with and without interstitial air holes (IAHs) are numerically investigated by the multipole method. It is shown that the IAHs can favorably decrease the confinement loss and the effective mode area of IGPCFs, and simultaneously increase the nonlinear coefficient in the IGPCFs. In addition, at the same air hole diameter d and pitch Λ, IGPCFs with IAHs can shift the position of the zero-dispersion wavelengths to the shorter wavelengths and make the group-velocity dispersion more flattened in the region of anomalous dispersion. By comparing the optical properties of the PCFs in the presence/absence of IAHs and at the same air-filling fractions, it is shown that the change in the optical properties induced by the presence of IAHs is different from those achieved by a simple increase of the air-filling fraction, a result attributed to stronger scattering by IAHs. PACS 42.81.-I; 42.81.Bm; 42.81.Qb     

波长间隔可调的可开关双波长掺铒光纤激光器

对两种波长间隔可调的可开关双波长掺铒光纤激光器结构进行了实验研究。一种结构应用保偏光纤中布拉格光栅作为波长选择器件，另一种结构则利用侧向压力下的常规单模光纤光栅作为波长选择器件。两种结构均利用了光纤光栅的双折射特性。在室温下，通过调整偏振控制器的状态可使两激光器工作在稳定的双波长状态或在两单波长之间转换。通过改变加在光纤光栅上侧向应力的大小和方向，可有效控制双波长激射的波长间隔。     

椭圆空气孔微结构光纤限制损耗的分析

以完美匹配层为边界条件,用复有限元法分析了椭圆空气孔三角形微结构光纤中基模的限制损耗.数值结果表明: 当孔间距,空气填充率和空气孔环数增大时,基模的限制损耗减小.从计算结果还可以得出:限制损耗与基模的偏振有关,随着孔间距,空气填充率和孔的椭圆率的增大,y偏振模与x偏振模的限制损耗比也增大.最后,提出了两种可实现光单偏振,单模传输的高非线性微结构光纤. 关键词： 微结构光纤 限制损耗 复有限元法 完美匹配层     

色散补偿光子晶体光纤结构参数对其色散的影响

光子晶体光纤由于其灵活可调的色散特性用作色散补偿具有极大的应用潜力. 设计了一种色散补偿光子晶体光纤, 并运用频域有限差分法模拟了其色散特性,从理论上分析了其结构参数孔间距Λ和空气占空比d/Λ对该光子晶体光纤的色散系数的影响, 并且实际制备出了3种不同结构参数的光子晶体光纤. 通过对其色散曲线对比分析表明: 当光子晶体光纤孔间距在1 μm附近时, 其色散系数随着孔间距Λ和占空比d/Λ的增大而增加, 但对于孔间距Λ的变化比占空比d/Λ更为敏感, 并且随着孔间距Λ的增加,其对色散系数的影响能力逐渐减小. 设计并制备的光子晶体光纤在1550 nm处的色散系数为-241.5 ps·nm^-1·km^-1, 相对色散斜率为0.0018, 具有较好的色散补偿能力. 关键词： 色散 色散补偿 光子晶体光纤 结构参数     

Temperature and strain discrimination using a single tilted fibre Bragg grating

A fibre optic sensor capable of discriminating between temperature and strain, using a single fibre Bragg grating, is presented. The technique exploits the core-cladding mode coupling of a tilted fibre Bragg grating (TFBG). The core and cladding modes exhibit different thermal sensivities, while the strain sensivities are approximately equal. Monitoring the core-core mode coupling resonance and the core-cladding mode coupling resonance of the TFBG spectrum allows the separation of the temperature and strain induced wavelength shifts.     

Oscillation wavelength of fiber Bragg grating semiconductor lasers

Based on the physical fact that a laser containing a gain medium with homogenous line broadening oscillates at the wavelength which requires the smallest threshold gain due to the mode competition effect, after taking into account the wavelength-depended reflectivity distribution profile of a fiber Bragg grating, the oscillation wavelength λ_l of fiber Bragg grating semiconductor lasers has been investigated theoretically. The results show that the laser oscillation wavelength λ_B is not fixed at the Bragg reflection wavelength λ_l of fiber Bragg grating, and the offset between λ_B and λ_l depends on the reflectivity distribution profile of fiber Bragg grating and the gain profile of semiconductor gain medium.     

Impact of interstitial air holes on a wide-bandwidth rejection filter made from a photonic crystal fiber

We have investigated the spectral properties of a band rejection filter made with a long-period fiber grating written in photonic crystal fiber that has interstitial air holes. Experiments showed that only one mode was coupled strongly to the fundamental core mode over a 600 nm spectral range. The central wavelength of the filter could be tuned over that range without being appreciably affected by any other mode. By using the multipole method, we found that the interstitial air holes of the photonic crystal fiber played a critical role in limiting the number of modes that could strongly interact with the fundamental mode and in obtaining well-separated resonance peaks. Excellent agreement between theory and experiment was obtained.     

Optimization of highly nonlinear dispersion-flattened photonic crystal fiber for supercontinuum generation

A simple type of photonic crystal fiber (PCF) for supercontinuum generation is proposed for the first time. The proposed PCF is composed of a solid silica core and a cladding with square lattice uniform elliptical air holes, which offers not only a large nonlinear coefficient but also a high birefringence and low leakage losses. The PCF with nonlinear coefficient as large as 46 W 1 · km-1 at the wavelength of 1.55 μm and a total dispersion as low as ±2.5 ps · nm-1 · km-1 over an ultra-broad waveband range of the S-C-L band (wavelength from 1.46 μm to 1.625 μm) is optimized by adjusting its structure parameter, such as the lattice constant Λ , the air-filling fraction f , and the air-hole ellipticity η. The novel PCF with ultra-flattened dispersion, highly nonlinear coefficient, and nearly zero negative dispersion slope will offer a possibility of efficient super-continuum generation in telecommunication windows using a few ps pulses.     

Study on pulse compression in tapered holey fibres

This paper proposes three kinds of tapered holey fibres with a multi-layer of holes whose pitch of air holes at the end of untapered and tapered are 5.8 μm and 1.8 μm. The central wavelength which locates in the anomalous dispersion region is 1.55 μm. An adaptive split-step Fourier method is numerically used to study the pulse propagation in tapered holey fibres. For the considered convex tapered holey fibre, at a wavelength of 1.55 μm, a compression factor of 136.7 can be achieved by initial width of 800 fs propagation through a length of 0.8 m. It demonstrates that in anomalous dispersion region, pulse can be compressed with the increase of nonlinearity coefficient and the decrease of dispersion coefficient.     

Broad and ultra-flattened supercontinuum generation in the visible wavelengths based on the fundamental mode of photonic crystal fibre with central holes

By coupling a train of femtosecond pulses with 100 fs pulse width at a repetition rate of 76 MHz generated by a mode-locked Ti:sapphire laser into the fundamental mode of photonic crystal fibre(PCF) with central holes fabricated through extracting air from the central hole,the broad and ultra-flattened supercontinuum(SC) in the visible wavelengths is generated.When the fundamental mode experiences an anomalous dispersion regime,three phases in the SC generation process are primarily presented.The SC generation(SCG) in the wavelength range from 470 nm to 805 nm does not emerge significant ripples due to a higher pump peak power and the corresponding mode fields at different wavelengths are observed using Bragg gratings.The relative intensity fluctuations of output spectrum in the wavelength ranges of 530 nm to 640 nm and 543 nm to 590 nm are only 0.028 and 0.0071,respectively.     

The system of L-band 2×10 Gb/s WDM transmission over conventional single mode fibre with 600 km by chirped fibre Bragg gratings dispersion compensation

A chirped fibre Bragg grating according to ITU-T suggested L-band (2nd channel $\lambda _{1}=1570.83$~nm; 80th channel $\lambda _{2}=1603.57$ nm) with more than 1800 ps/nm single channel dispersion compensation is presented in this paper, of which the cladding mode loss, the delay curve ripple and the power fluctuation of the reflected spectrum are less than 0.5 dB, 50 ps and 0.25 dB, respectively. With this new FBG as dispersion compensation device, a $2\times 10$ Gb/s wavelength division multiplexing (WDM) L-band transmission of 600 km based on conventional single mode fibre (G.652 fibre) is performed without forward error correction. The bit error rate (BER) is less than 10$^{ - 12}$ and the power penalties of the 2{nd} and 80{th} channel of L-band are 1.8~dB and 2.0~dB, respectively.     

相位修正的耦合模理论用于计算光纤Bragg光栅法布里-珀罗腔透射谱

基于光纤Bragg光栅(FBG)反射复振幅相移对FBG法布里-珀罗腔透射谱的影响,分析了传统耦合模理论计算均匀FBG反射复振幅相移产生误差的原因.引入折射率分布初始相位参数描述FBG折射率分布纵向的微小偏移,用真实的反透射系数代替简明形式的反透射系数,对传统耦合模理论进行了修正,增加了与折射率分布初始相位参数有关而与波长无关的相位因子.在此基础上进一步对计算非均匀FBG的传输矩阵法的相位进行了修正.修正后的快速计算结果用于FBG法布里-珀罗腔透射谱的计算,可反映折射率分布初始相位参数对透射峰波长位置的影响,与Rouard 算法及实验值均有较好的一致性. 关键词： 光纤Bragg 光栅 法布里-珀罗腔 耦合模理论     

Operation of Tm3+ fiber laser at λ = 2.3 μm coupled to a silica fiber Bragg grating

A wavelength tunable all fibre laser which utilizes Tm³⁺-doped fluoride fibre as a gain mechanism emitting around a wavelength of = 2.3 m is reported. Tm³⁺-doped fluoride fibre was coupled to a fibre Bragg grating inscribed in silica. This laser was evaluated by employing it as a wavelength tunable source in a methane gas optical sensor. A minimum gas detectivity of 100 ppm m limited by the ability to prepare low concentrations of gases was achieved. Emission wavelength control was implemented by thermally tuning the grating, although this method may prove to be too slow and cumbersome for practical use. A model describing the coupling between the silica fibre Bragg grating and the Tm³⁺-doped fibre was developed and integrated with a fibre laser model. This theoretical framework was used to examine the optimum silica and fluoride fibre parameters to achieve the maximum coupling between the fibres, with the aim of further reducing the fibre laser threshold.     

Hetero-core fiber Bragg grating for simultaneous measurement of strain and bending based on cladding mode ratiometric detection

A simple but practical method using multimode-single mode fiber Bragg grating (FBG) for cladding mode based simultaneous measurement of strain and bending is proposed and investigated experimentally. Experimental results show that the intensity ratio between cladding mode and FBG resonance of hetero-core FBG show monotonous changes following with the increase of deflection, by which strain and bending discrimination can be achieved by measuring the wavelength shift of FBG resonance and ratiometrically detecting the intensity changes between cladding modes and FBG resonance.     

光子晶体光纤拉制中工艺参数的控制

分析了光子晶体光纤拉制中各工艺参数之间的相互影响,建立了工艺参数与最终光纤结构之间的对应关系.在温度和送料速度的协调控制下,通过调节气压参数可有效控制气孔结构.实验拉制出孔径孔距比分别为0.45和0.8的单模以及高占空比光子晶体光纤.在制备非均匀孔径光子晶体光纤时,仅靠调控工艺参数往往难以拉制出理想结构,本文以一种单偏振单模PCF结构为例,对预制棒结构进行了优化设计.计算表明可由此拉制出满足要求的光子晶体光纤. 关键词： 光子晶体光纤 工艺参数 气压控制 气孔结构     

Fibre Bragg Gratings Inscribed in Homemade Microstructured Fibres

Fibre Bragg gratings （FBGs） are inscribed in homemade microstructured fibres by the standard phase mask method. Enhanced couplings between the forward fundamental mode and backward cladding modes are obtained. The mode coupling and spectral characteristics are investigated experimentally. The cladding mode resonances can be affected by filling active materials into the air holes, which will be useful for the implementation of tunable photonic devices in optical fibre communication and sensing systems.     

Novel tunable fiber-optic edge filter based on modulating the chirp rate of a π-phase-shifted fiber Bragg grating in transmission

We propose and experimentally demonstrate a novel fiber-optic edge filter based on modulating the chirp rate of a π-phase-shifted fiber Bragg grating (FBG) operating in transmission mode. The phase shift induced passband in the transmission spectrum is utilized as the edge filter. The dependence of the π-phase-shifted FBG’s transmitted spectral response on the chirp rate has been numerically studied in detail and experimentally confirmed, to the best of our knowledge, for the first time. The linear wavelength range of the proposed edge filter can be tuned by changing the chirp rate of FBG. The edge filter is further tested as a wavelength interrogator, and the experimental results are in good agreement with numerical results. The proposed fiber-optic edge filter has several unique advantages which include simple structure, cost effectiveness, high sensitivity, flexible tunability, and optical circulator is not required, and thus has interesting potential applications, especially as a wavelength interrogator in FBG foot sensors, FBG ultrasound and vibration sensors, and FBG distributed sensors, where the required wavelength ranges are very small (<0.4 nm).     

Development of tilted fibre Bragg gratings using highly coherent 255 nm radiation

This paper reports the study on development of tilted fibre Bragg gratings using highly coherent 255 nm radiation, obtained from the second harmonic generation (SHG) of copper vapour laser (CVL). The transmission and reflection spectra of the tilted fibre Bragg gratings (TFBG) were studied for the tilt angles of 0° (normal FBG), 1°, 3° and 4° between the fibre axis and the interference fringe plane. It was observed that as the angle of fibre axis and phase mask increased, the main Bragg peak shifted towards the higher wavelength and transmission dip decreased. The transmission dip of the cladding mode first increased and then decreased after reaching a maximum with the increase in the tilt angle.     

High resolution instrumentation system for fibre-Bragg grating aerospace sensors

A passive technique for high-resolution detection of the wavelength of peak reflection from fibre Bragg grating (FBG) sensors is presented. The approach, based on a de-convolution of the FBG spectrum and the spectrometer resolution, essentially overcomes the low spectral resolution (≈0.1 nm) associated with commercial spectrometers employing CCD detection. The performance of two algorithms, the Centroid Detection algorithm (CDA) and the least squares method (LSQ), are compared. The LSQ algorithm offers resolution enhancement of at least two orders of magnitude and is shown to be independent of the FBG intensity and bandwidth over a broad range.     

Acoustic longitudinal mode coupling in w-shaped Al/Ge Co-doped fibre

This paper proposes a novel fibre structure aiming at distributed temperature and strain sensing. Utilizing Al₂O₃ and GeO₂ as dopants to form a w-shaped acoustic waveguide, it realizes modal coupling between longitudinal acoustic modes of its inner and outer core layers, leading to a dual-peak or multi-peak Brillouin gain spectrum. The relationship between the acoustic mode coupling properties and the fibre materials, doping concentrations and structural parameters are investigated, showing that the positions of mode coupling points in acoustic dispersion curves and the coupling intensities can be designed flexibly. A specific fibre design for the discriminative sensing of temperature and strain under a pump wavelength of 1.55 μm is given. The responses of its Brillouin gain properties on temperature and strain are analysed theoretically, demonstrating its potential for distributed fibre Brillouin sensing.