高质量高取向(100)面金刚石膜的可控性生长

应用微波等离子体化学气相沉积技术, 在低气压下对(100)晶面金刚石膜的表面形貌、质量、取向和生长率进行了可控性生长研究. 结果表明: 基片温度与甲烷浓度对(100)晶面金刚石膜的生长存在耦合规律. 为了获得表面形貌相似的(100)晶面金刚石膜, 在沉积过程中, 增加碳源浓度的同时需要同时升高基片温度; 当甲烷浓度为3.0%, 基片温度从740 ℃上升至1100 ℃ 的过程中, 金刚石膜的晶面取向变化可分为五个阶段, 其中当基片温度在860 ℃至930 ℃时, 很适合高取向(100)晶面金刚石膜生长; 另外, 金刚石膜的质量和生长速率分别与基片温度和甲烷浓度成正比. 为了获得高质量高取向(100)晶面金刚石膜, 应当选择合适的基片温度和甲烷浓度.     

CVD金刚石膜的结构分析

利用x射线广角衍射和低角掠入射散射谱、正电子湮没谱、定性分析软件和Positronfit程序，研究了生长在Si（100）基底上的金刚石膜微结构.研究发现，在样品邻近基底区域为纳米 多晶结构，具有弱的［111］织构；在邻近表面区域为微米多晶结构，具有强的［220］织构 .金刚石膜样品有空位、空位团和空洞3种缺陷，其中主要缺陷是大约10个空位形成的空位团 . 关键词： 金刚石膜 化学气相沉积 x射线掠入射 正电子湮没谱     

氧化铝基片上沉积金刚石薄膜的Raman光谱分析

分别采用微波等离子体化学汽相沉积法和热丝化学汽相沉积法在氧化铝陶瓷基片上沉积金刚石薄膜．通过谱线拟合，定量比较了不同沉积方法、不同基片上沉积金刚石薄膜的质量，计算了沉积膜的结构完整性及沉积层的应变，其结果与X射线衍射的结果符合良好 关键词：     

不同方法测量铜薄膜厚度的比较

利用磁致溅射方法在玻璃基片上沉积不同厚度的铜膜。利用台阶仪、反射光谱法、四探针电阻法分别测量铜薄膜的形状膜厚、光学膜厚、电阻膜厚。总结了三种方法的测量精度、测量范围和局限性。     

微喇曼和红外光谱法研究化学气相沉积金刚石多晶膜结晶质量特性

研究了化学气相沉积多晶膜的宏观性能（颜色和透光性）与微观性能（结晶质量、相纯度和氢杂质含量）之间的关系,喇曼谱与金刚石膜中氢杂质含量（红外光谱测得）的关联性.给出了根据颜色和透明度来区分样本膜质量的实验依据,颜色较深的膜的结晶质量差、相纯度低、氢杂质含量高,1 332 cm－1金刚石特征喇曼峰强度低,半峰宽大.由于多晶膜生长不均匀性、多晶以及粗糙度的影响,生长面的微喇曼光谱随采样点变化会产生较大的偏差,而光滑生长界面的喇曼光谱随采样点的变化偏差较小,因此生长界面的喇曼光谱更能反映化学气相沉积法制备金刚石膜的整体质量.     

刚性衬底上铜铟硒纳米棒阵列的合成与表征

在覆盖有钨电极的硅衬底上利用多孔阳极氧化铝模板为生长掩膜电沉积合成垂直排列的铜铟硒纳米棒阵列. 多孔阳极氧化铝模板由阳极氧化磁控溅射制备的铝膜制成. 扫描电子显微镜结果表明,该纳米棒阵列结构致密,直径约100 nm长度约1μm,纵横比为10. X射线衍射、微区拉曼光谱和高分辨透射电子显微镜结果表明,真空条件下450 oC退火处理的铜铟硒纳米棒是多晶纯相的黄铜矿结构的铜铟硒,在纳米棒轴向方向上有比较大的晶粒尺寸. 能量色散X射线光谱表明,铜铟硒纳米棒的化学组成接近InSe₂的化学计量比,由吸收光谱分析推算铜铟硒纳米棒带隙为0.96 eV.     

微波等离子体化学气相沉积金刚石膜

微波等离子体化学气相沉积是制备金刚石膜的一个重要方法，能制备出表面光滑平整的大面积均匀金刚石膜，文章概述了ＭＰＣＶＤ制备金刚石膜的情况，介绍了ＭＰＣＶＤ制备金刚石膜装置的典型类型及其特点，在国内研制成功天线耦合石英钟罩式ＭＰＣＶＤ制备金刚石膜装置，并在硅片上沉积出大面积均匀的优质金刚石膜。     

金刚石膜/多孔硅复合材料的性能表征

提出了一种新颖的多孔硅表面钝化技术,即采用微波等离子体辅助的化学气相沉积（MPCVD）方法在多孔硅上沉积金刚石薄膜。采用原子力显微镜（AFM）、扫描电子显微镜（SEM）、X射线衍射仪（XRD）、拉曼光 谱仪和荧光分光度计对多孔硅及金刚石膜的表面形貌、结构和发光特性进行了表征。结果表明采用微波等离子体化学气相沉积法可在多孔硅基片上形成均匀、致密、性能稳定且对可见光具有全透性的金刚石膜。金刚石膜与多孔硅的复合,大大稳定了多孔硅的发光波长和强度,同时增强了多孔硅的机械强度。     

硅基籽晶上化学气相沉积金刚石薄膜及其场发射特性

通过控制电泳沉积(EPD)时间,在硅基片上沉积不同密度的金刚石籽晶。再用热丝化学气相沉积(HFCVD)设备,在硅基籽晶上合成多晶金刚石薄膜。薄膜中通常含有非金刚石相碳成分。用扫描电子显微镜(SEM)和Raman光谱对样品的表面形貌和成分进行了表征,测量了样品的场发射特性。比较并分析了样品的表面形貌和非金刚石成分上的差异对金刚石薄膜场发射特性的影响。     

拉丝成品模用生长型多晶金刚石

人造多晶金刚石是研制大颗粒人造金刚石的一种重要途径,它制作方便,易于直接成型.目前在高温高压下有两种研制方法:一是由石墨合成金刚石,再由金刚石微粉烧结成多晶金刚石,即烧结型多晶金刚石(也称烧结型聚晶);另一就是由石墨直接一次生长成多晶金刚石,即生长型多晶金刚石(也称生长型聚晶). 人造多晶金刚石已在机械、地质、冶金、石油工业中广泛应用.近几年在电线、电缆行业中,也开始以人造金刚石拉丝模代替天然金刚石拉丝模和硬质合金模。天然金刚石模价格贵,资源少.硬质合金模耐磨性差,使用寿命短.所以,人造多晶金刚石拉丝模有着广阔的应…     

Study of microwave plasma-assisted chemical vapor deposition of poly-and single-crystalline diamond films

We study conditions for microwave plasma-assisted chemical vapor deposition of high-quality single-crystal diamond films in a CVD reactor. These conditions are studied using the results of homoepitaxial growth of polycrystalline diamond films on diamond substrates and on the basis of numerical simulation of the microwave discharge in a CVD reactor. A high-quality single-crystal diamond layer is synthesized on a synthetic, type Ib diamond substrate. The properties of the obtained monolayer are studied by means of Raman and X-ray diffraction spectroscopy as well as optical and atomic-force microscopy.     

Wettability and crystalline orientation of Cu nanoislands on SiO<Subscript>2</Subscript> with a Cr underlayer

Cu thin films were grown by sputter deposition on SiO₂ substrates with a Cr underlayer that is known to improve the adhesion between Cu and SiO₂. The initial stage of Cu growth was investigated using transmission electron microscopy. Results showed that non-wetting spherical Cu nanoislands were formed with a random crystalline orientation on Cr/SiO₂, and evolved into a randomly oriented polycrystalline thin film. These results were then compared with our previous results on the initial growth of Cu on SiO₂ with and without a Ti underlayer. A quantitative model was proposed to explain the difference in dependence of the wettability of microscopic nanoislands and that of the adhesion of macroscopic thin films on interfacial interactions and surface energies. PACS 61.46.+w; 68.35.Md; 68.35.Np     

Fabrication of aligned carbon nanotubes on Cu catalyst by dc plasma-enhanced catalytic decomposition

Aligned multi-walled carbon nanotubes (ACNTs) are deposited using copper (Cu) catalyst on Chromium (Cr)-coated substrate by plasma-enhanced chemical vapor deposition at temperature of 700 °C. Acetylene gas has been used as the carbon source while ammonia is used for diluting and etching. The thicknesses of Cu films on Cr-coated Si (100) substrates are controlled by deposition time of magnetron sputtering. The growth behaviors and quality of ACNTs are investigated by scanning electron microscopy (SEM) and transmission electron microscopy. The different performance of ACNTs on various Cu films is explained by referring to the graphitic order as detected by Raman spectroscopy. The results indicate that the ACNTs are formed in tip-growth model where Cu is used as a novel catalyst, and the thickness of Cu films is responsible to the diameter and quality of synthesized CNTs.     

Enhanced diamond nucleation on copper substrates by graphite seeding and CO2 laser irradiation

Diamond nucleation on copper (Cu) substrates was investigated by graphite seeding and CO₂ laser irradiation at initial stages of the combustion-flame deposition. A graphite aerosol spray was used to generate a thin layer of graphite powders (less than 1 μm) on Cu substrates. The graphite-seeded Cu substrates were then heated by a continuous CO₂ laser to about 750 °C within 1 min. It was found that diamond nucleation density after this treatment was more than three times as much as that on the virgin Cu substrates. As a consequence, diamond films up to 4 μm were obtained in 5 min. The enhancement of diamond nucleation on the graphite-seeded Cu substrates was attributed to the formation of defects and edges during the etching of the seeding graphite layers by the OH radicals in the flame. The defects and edges served as nucleation sites for diamond formation. The function of the CO₂ laser was to rapidly heat the deposition areas to create a favorable temperature for diamond nucleation and growth.     

衬底对Cu(In,Ga)Se2薄膜织构的影响

分别在苏打石灰玻璃、Mo箔、无择优取向的Mo薄膜以及(110)择优取向的Mo薄膜四种不同衬底上，采用共蒸发工艺沉积约2 μm厚的Cu(In,Ga)Se₂薄膜，用X射线衍射仪测量薄膜的织构，研究衬底对Cu(In,Ga)Se₂薄膜织构的影响.在以上四种衬底上沉积的Cu(In,Ga)Se₂薄膜的(112)衍射峰强度依次逐渐减弱，(220/204)衍射峰从无到有且强度逐渐增强.在苏打石灰玻璃和Mo箔衬底上的Cu(In,Ga)Se_{2关键词： 择优取向 Cu(In 2}薄膜')" href="#">Ga)Se₂薄膜 太阳电池     

Growth and Characteristics of Freestanding Hemispherical Diamond Films by Microwave Plasma Chemical Vapor Deposition

Freestanding hemispherical diamond films have been fabricated by microwave plasma chemical vapor deposition using graphite and molybdenum （Mo） as substrates. Characterized by Raman spectroscopy and scanning electron microscopy, the crystalline quality of the films deposited on Mo is higher than that on graphite, which is attributed to the difference in intrinsic properties of the two substrates. By decreasing the methane concentration, the diamond films grown on the Mo substrate vary from black to white, and the optical transparency is enhanced. After polishing the growth side, the diamond films show an infrared transmittance of 35-60% in the range 400-4000 cm^- 1.     

富勒烯作为过渡层生长金刚石薄膜研究

采用微波等离子体化学气相淀积法，以Ｃ６０膜过渡层，在光滑的单晶Ｓｉ衬底（１００）表面的研磨的石英衬底表面等光学衬底上，首次在无衬底负偏压条件下生长出多晶金刚石薄膜，通过扫描电镜观察到生长膜晶粒呈莱花状，生长表面为金刚石（１００）界面。     

Optical and structural properties of polycrystalline CVD diamond films grown on fused silica optical fibres pre-treated by high-power sonication seeding

In this paper, the growth of polycrystalline chemical vapour deposition (CVD) diamond thin films on fused silica optical fibres has been investigated. The research results show that the effective substrate seeding process can lower defect nucleation, and it simultaneously increases surface encapsulation. However, the growth process on glass requires high seeding density. The effects of suspension type and ultrasonic power were the specific objects of investigation. In order to increase the diamond density, glass substrates were seeded using a high-power sonication process. The highest applied power of sonotrode reached 72 W during the performed experiments. The two, most common diamond seeding suspensions were used, i.e. detonation nanodiamond dispersed in (a) dimethyl sulfoxide and (b) deionised water. The CVD diamond nucleation and growth processes were performed using microwave plasma assisted chemical vapour deposition system. Next, the seeding efficiency was determined and compared using the numerical analysis of scanning electron microscopy images. The molecular composition of nucleated diamond was examined with micro-Raman spectroscopy. The sp³/sp² band ratio was calculated using Raman spectra deconvolution method. Thickness, roughness, and optical properties of the nanodiamond films in UV–vis wavelength range were investigated by means of spectroscopic ellipsometry. It has been demonstrated that the high-power sonication process can improve the seeding efficiency on glass substrates. However, it can also cause significant erosion defects at the fibre surface. We believe that the proposed growth method can be effectively applied to manufacture the novel optical fibre sensors. Due to high chemical and mechanical resistance of CVD diamond films, deposition of such films on the sensors is highly desirable. This method enables omitting the deposition of an additional adhesion interlayer at the glass–nanocrystalline interface, and thus potentially increases transmittance of the optical system.     

Formation of two-dimensional periodic nanostructures on fused quartz,polyimide, and polycrystalline diamond by pulsed four-wave interference laser modification

Atomic force microscopy is used to examine the topography of submicron periodic structures formed on the surfaces of synthetic polycrystalline diamond and polyimide films. The films are deposited on fused quartz substrates by four-wave interference modification using a pulsed 308-nm UV XeCl excimer laser. It is demonstrated that a two-dimensional periodic relief with a submicron period can be formed on the diamond surface directly by laser evaporation in the absence of a photoresist. Depending on the exposure, two mechanisms of polyimide film modification are observed. At exposures less than 100 mJ/cm², the relief is formed due to swelling at the positions of interference maxima. At exposures greater than 100 mJ/cm², holes are formed in the films. A periodic relief on the fused quartz surface is formed by using a UV photoresist exposed to pulsed interference laser radiation and subsequent Ar ion etching.     

Effect of copper surface morphology on grain size uniformity of graphene grown by chemical vapor deposition

The graphene grain boundaries (GGBs) of polycrystalline graphene grown by chemical vapor deposition (CVD) typically constitute a major reason of deterioration of the electrical properties of graphene-based devices. To reduce the density of GGB by increasing the grain size, CVD growth conditions with a reduced CH₄ flow rate have been widely applied and, recently, electropolishing of copper (Cu) foil substrates to flatten the surface has been undertaken prior to graphene growth. In this study, we show that polycrystalline graphene layer grown on typical Cu foil features two heterogeneous regions with different average grain sizes: small-grain regions (SGRs) and large-grain regions (LGRs). Statistical analysis of the grains of the graphene layers grown under different process conditions showed that SGRs (which form on Cu striations) limit the average grain size, the ability to control the grain size through adjustment of growth conditions, and global grain-size uniformity. Analysis showed that the surface-flattening process significantly improves grain-size uniformity, and monolayer coverage, as well as the average grain size. These results suggest that a process for flattening the surfaces of Cu substrates is critical to controlling the quality and uniformity of CVD-grown graphene layers for practical device applications.