多孔硅发光峰温度行为的研究

实验研究了多孔硅（Ｐｏｒｏｕｓ Ｓｉｌｉｃｏｎ）光致发光峰随测量温度的变化,发现发光峰位随温度的移动与发光峰的能量有关。随温度升高,发光峰波长较长的样品它们的发光峰都移向高能,面发光峰能量较高的样品它们的发光峰都移向低能,发光峰波长位于７４０ｎｍ附近的样品,它们的发光峰与测量温度无关。对上术结果的起源作了讨论。     

多孔硅的制备条件对其光致发光特性的影响

不同的实验条件下制备的多孔硅的光致发光(PL)特性是不同的,这是许多研究产生分歧的主要原因。对比分析了阳极氧化电流密度、阳极氧化时间、溶液浓度以及自然氧化时间对多孔硅光致发光光谱的影响。认为在一定的范围内,多孔硅的发光峰位会随电流密度的增大而蓝移,要获得较强的发光,需要选择合适的电流密度;随着腐蚀时间的延长,多孔硅的发光峰位也发生蓝移。当HF酸的浓度较小时,峰位随浓度的增大表现为向低能移动;而当HF酸的浓度较大时,峰位随浓度的增大则表现为移向高能。多孔硅在空气中自然氧化,其发光峰位发生蓝移,而发射强度随放置时间的延长而降低。并用量子限制模型和发光中心模型对实验结果进行解释。     

多孔硅衬底上溅射沉积SiC:Tb薄膜的光致发光行为

在多孔硅衬底上用射频溅射法沉积了非晶的SiC:Tb薄膜. 对样品在N2中进行了不同温度的退火处理. 用傅里叶红外变换谱分析了样品的结构.用荧光光谱仪测试了样品的光致发光，在紫外、可见光区域观测到了强的发光峰.发现随着衬底加热温度和样品退火温度的变化，发光峰有明显的强度变化和微弱的蓝移现象.分析了产生这种现象的机理，得出了紫外区域的发光峰是由于氧缺乏中心引起的，而可见区的发光是由于Tb离子产生的. 关键词： 碳化硅 光致发光 氧缺乏中心 多孔硅     

不同退火条件对纳米多孔氧化铝薄膜光致发光的影响

以草酸为电解液,采用二次阳极氧化法制备出了纳米多孔氧化铝薄膜,经不同退火温度和退火气氛处理氧化铝薄膜后,通过分析其光致发光光谱得出：相同的退火气氛中, 退火温度T≤600 ℃ 时,T=500 ℃具有最大的光致发光强度;退火温度T≥700 ℃时,随着退火温度的升高,样品的发光强度增大。在不同的退火气氛中,多孔氧化铝薄膜随着退火温度的升高,发光峰位改变不同,即在空气中退火处理后,随着退火温度的升高,发光峰位蓝移,而在真空中退火处理后,发光峰位并不随退火温度的升高而变化;通过对1 100 ℃高温退火处理后的氧化铝薄膜的光致发光曲线的高斯拟合,可以看出,经退火处理后的多孔氧化铝,主要存在三个发光中心,发光曲线在350～600 nm范围内对应三个发射峰, 发射波长分别为387,410,439 nm。相同的退火温度下,空气中退火得到的氧化铝薄膜的光致发光强度大于真空中退火处理后的氧化铝薄膜。基于实验结果,结合X射线色散能谱(EDS)、红外反射光谱等表征手段,探讨了多孔氧化铝薄膜的发光机制,并对经过不同退火条件得到的多孔氧化铝薄膜的光致发光特性的改变做出了合理的解释。     

多孔硅在30~180℃温区光致发光谱的研究

对长期存放在空气中的多孔硅样品和即时制备的多孔硅样品分别在室温~180℃下进行了光致发光（PL）温度效应的研究.两类样品的PL呈现不同的变化规律.前者的PL还表现为双峰,且长波PL峰随温度升高蓝移;后者的PL表现为单峰,且PL峰位随温度升高红移.基于量子限制效应对后者进行了解释;而前者难以用分立的量子限制和表面发光中心模型来解释,实验结果表明两种机制之间可能有较复杂的耦合效应发生.     

包含硅量子点的富硅SiNx 薄膜结构与发光特性

采用等离子体增强化学气相沉积法, 以NH₃与SiH₄为反应气体, n型单晶硅为衬底, 低温(220 ℃)沉积了富硅氮化硅(SiN_x)薄膜. 在N₂氛围中, 于500–1100 ℃ 范围内对样品进行了热退火处理. 采用Raman 光谱技术分析了薄膜内硅量子点的结晶情况, 结果表明, 当退火温度低于950 ℃时, 样品的晶化率低于18%, 而当退火温度升为1100 ℃, 晶化率增加至53%, 说明大部分硅量子点都由非晶态转变为晶态. 实验通过Fourier 变换红外吸收(FTIR)光谱检测了样品中各键的键合结构演变, 发现Si–N键和Si–H键随退火温度升高向高波数方向移动, 说明了薄膜内近化学计量比的氮化硅逐渐形成. 实验还通过光致发光(PL)光谱分析了各样品的发光特性, 发现各样品中均有5个发光峰, 讨论了它们的发光来源, 结合Raman光谱与FTIR光谱表明波长位于500–560 nm的绿光来源于硅量子点, 其他峰则来源于薄膜内的缺陷态. 研究了硅量子点的分布和尺寸对发光带移动的影响, 并根据PL峰位计算了硅量子点的尺寸, 其大小为1.6–3 nm, 具有良好的限域效应. 这些结果有助于制备尺寸不同的硅量子点和基于硅量子点光电器件的实现. 关键词： 硅量子点 氮化硅薄膜 光致发光 Fourier 变换红外吸收     

非桥氧空穴发光中心对铁钝化多孔硅光致发光的影响

采用水热腐蚀法制备了铁钝化多孔硅样品,样品光致发光谱的荧光峰位于2.0eV附近,半峰宽约为0.40eV。激发波长从240nm增大到440nm的过程中,荧光峰先红移再蓝移,最后基本稳定,变化曲线呈勺型。通过分析15片发光多孔硅样品的统计结果,发现荧光峰逆转所对应的激发波长位于330nm附近,相应的激发光子能量约为3.8eV。样品光致发光谱随激发波长的勺型变化过程与≡Si—O↑和≡Si—O↑…H—O—Si≡两类非桥氧空穴发光中心共同作用时的发光行为一致。     

发光不衰减的多孔硅

用一种新的方法制备出了具有不同衰减的光致发光特性的多孔硅。如此制备的多孔硅新鲜样品,其发光峰位强度比普通多孔硅高２￣２．５倍,将样品在室温下暴露于空气中,其发光强度在前４个月中单调增加,然后达到饱和。在随后的８个月中,没有观察到发光衰减,发光峰位也没有发生变化,这种发光稳定性被归因子于多孔硅表面所形成的稳定的Ｆｅ－Ｓｉ键。文章探讨了发光不衰减、峰位不蓝移的机理,并为多孔硅发光的量子限域模型提供了强     

有机吸附物对多孔硅微腔发光的影响

理论上,采用Bruggeman有效介质近似,研究了有机吸附物对多孔硅微腔的折射率及其光致发光谱的影响.实验上,采用计算机控制的电化学腐蚀法制备了多孔硅微腔样品,并利用机械泵油的蒸气分子与该微腔样品进行相互作用.研究发现,多孔硅微腔发射的窄化光致发光谱对泵油蒸气分子的吸附与脱附很敏感,与之伴随的是该窄化光致发光谱发生明显的峰位移动(可达71nm)和强度变化.结合Bruggeman近似和表面态对多孔硅发光的影响,对实验结果进行了定性解释.实验结果与理论模拟结果符合较好. 关键词： Bruggeman近似 吸附物 多孔硅微腔 光致发光谱     

高温氧化多孔硅的电子束辐照效应

通过高温氧化处理得到的多孔硅,其阴极射线发光谱呈现明显的三峰结构。峰强随电子束辐照时间而下降。对光致发光很弱的样品,电子束辐照后光致发光明显地增强。红外透射谱及Raman谱分析表明样品基本上成为SiO_x.进一步分析指出三峰可能来源于SiO_x中的缺陷中心发光。电子束辐照在SiO_x禁带中引进了一些缺陷能级,通过这些能级使得紫外线可激发样品发光,出现光致发光增强的现象。     

Anomalous photoluminescence of InAs quantum dots implanted by Mn ions

The photoluminescence (PL) of Mn-implanted quantum dot (QD) samples after rapid annealing is studied. It is found that the blue shift of the PL peak of the QDs, introduced by the rapid annealing, decreases abnormally as the implantation dose increases. This anomaly is probably related to the migration of Mn atoms to the InAs QDs during annealing, which leads to strain relaxation when Mn atoms enter InAs QDs or to the suppression of the inter-diffusion of In and Ga atoms when Mn atoms surround QDs. Both effects will suppress the blue shift of the QD PL peaks. The temperature dependence of the PL intensity of the heavily implanted QDs confirms the existence of defect traps around the QDs.     

Photoluminescence in powdered crystalline GeSe2

The decrease of photoluminiscence (PL) intensity under continuous excitation in powdered crystalline GeSe₂ was observed at 77 K. The intensity of PL decreased by ～ 50 % in 2.10³s. The characteristics of the PL band for the powdered samples at 77 K are identical with those for crystals, but the temperature dependence of the PL intensity and the peak of the PL spectrum in the temperature range 77–200 K for powdered and bulk crystalline samples are different.     

Optoelectronic characterization of ZnS/PS systems

ZnS thin films are deposited on porous silicon （PS） substrates with different porosities by pulsed laser deposition （PLD）. The photoluminescence （PL） spectra of the samples are measured at room temperature. The results show that the PL intensity of PS after deposition of ZnS increases and is associated with a blue shift. With the increase of PS porosity, a green emission at about 550 nm is observed in the PL spectra of ZnS/PS systems, which may be ascribed to the defect-center luminescence of ZnS films. Junction current- voltage （I-V） characteristics were studied. The rectifying behavior of I-V characteristics indicates the formation of ZnS/PS heterojunctions, and the forward current is seen to increase when the PS porosity is increased.     

Effect of different electrolytes on porous GaN using photo-electrochemical etching

This article reports the properties and the behavior of GaN during the photoelectrochemical etching process using four different electrolytes. The measurements show that the porosity strongly depends on the electrolyte and highly affects the surface morphology of etched samples, which has been revealed by scanning electron microscopy (SEM) images. Peak intensity of the photoluminescence (PL) spectra of the porous GaN samples was observed to be enhanced and strongly depend on the electrolytes. Among the samples, there is a little difference in the peak position indicating that the change of porosity has little influence on the PL peak shift, while it highly affecting the peak intensity. Raman spectra of porous GaN under four different solution exhibit phonon mode E₂ (high), A₁ (LO), A₁ (TO) and E₂ (low). There was a red shift in E₂ (high) in all samples, indicating a relaxation of stress in the porous GaN surface with respect to the underlying single crystalline epitaxial GaN. Raman and PL intensities were high for samples etched in H₂SO₄:H₂O₂ and KOH followed by the samples etched in HF:HNO₃ and in HF:C₂H₅OH.     

Anomalous optical transitions in AlInGaN/GaN heterostructures grown by metalorganic chemical vapor deposition

Using temperature-dependent photoluminescence (PL) measurements, we report a comprehensive study on optical transitions in Al_yIn_xGa_1−x−yN epilayer with target composition, x=0.01 and y=0.07 and varying epilayer thickness of 40, 65 and 100 nm. In these quaternary alloys, we have observed an anomalous PL temperature dependence such as an S-shape band-edge PL peak shift and a W-shape spectral broadening with an increase in temperature. With an increase in excitation power density, the emission peak from the AlInGaN epilayers shows a blue shift at 100 K and a substantial red shift at room temperature. This is attributed to the localization of excitons at the band-tail states at low temperature. Compared to 40 and 65 nm thick epilayers, the initial blue shift observed with low excitation power from 100 nm thick AlInGaN epilayer at room temperature is caused by the existence of deeper localized states due to confinement effects arising from higher In and Al incorporation. The subsequent red shift of the PL peak can be attributed by free motion of delocalized carriers that leads to bandgap renormalization by screening. Due to competing effects of exciton and free carrier recombination processes, such behavior of optical transitions leads to two different values of exponent ‘k’ in the fitting of PL emission intensity as a function of excitation power.     

不同厚度CdSe阱层的表面上自组织CdSe量子点的发光性质

利用变温和变激发功率分别研究了不同厚度CdSe阱层的自组织CdSe量子点的发光。稳态变温光谱表明:低温下CdSe量子阱有很强的发光,高温猝灭,而其表面上的量子点发光可持续到室温,原因归结于量子点的三维量子尺寸限制效应;变激发功率光谱表明:量子点激子发光是典型的自由激子发光,且在功率增加时。宽阱层表面上的CdSe量子点有明显的带填充效应。通过比较不同CdSe阱层厚度的样品的发光,发现其表面上量子点的发光差异较大,这可以归结为阱层厚度不同导致应变弛豫的程度不同,直接决定了所形成量子点的大小与空间分布^[1]。     

Luminescence study of Si/Ge quantum dots

We present a photoluminescence (PL) study of Ge quantum dots embedded in Si. Two different types of recombination processes related to the Ge quantum dots are observed in temperature-dependent PL measurements. The Ge dot-related luminescence peak near 0.80 eV is ascribed to the spatially indirect recombination in the type-II band lineup, while a high-energy peak near 0.85 eV has its origin in the spatially direct recombination. A transition from the spatially indirect to the spatially direct recombination is observed as the temperature is increased. The PL dependence of the excitation power shows an upshift of the Ge quantum dot emission energy with increasing excitation power density. The blueshift is ascribed to band bending at the type-II Si/Ge interface at high carrier densities. Comparison is made with results derived from measurements on uncapped samples. For these uncapped samples, no energy shifts due to excitation power or temperatures are observed in contrast to the capped samples.     

磁控溅射制备ZnO薄膜的受激发射特性的研究

用射频磁控反应溅射法在二氧化硅衬底上制备ZnO薄膜。得到了在不同温度下ZnO薄膜的吸收与光致发光。观测到了纵光学波 (LO)声子吸收峰与自由激子吸收峰 ;室温 (30 0K)下 ,PL谱中仅有自由激子发光峰。这些结果证实了ZnO薄膜具有较高的质量。探讨了变温ZnO薄膜的发光特性。研究了ZnO薄膜的受激发射特性。