基于PTCDA的有机/无机光敏二极管结构优化

以p型硅和苝四甲酸二酐 （perylene-3,4,9,10-tetracarboxylic acid dianhydride,PTCDA）为异质结,梳状金（Au）薄膜作为顶电极和光入射窗口制备了光敏二极管。研究表明,PTCDA的厚度和Au电极的厚度对光敏二极管的光响应度有很大的影响。对比不同PTCDA厚度的器件性能,在PTCDA厚度为100 nm时,光响应度最高达到0.3 A/W。进而采用最优化的100 nm厚的PTCDA薄膜制备硅基光敏二极管,对比不同Au电极厚度的器件性能。在Au厚度为20 nm时,器件的光响应度达到最优化的0.5 A/W。     

Au电极厚度对MgZnO紫外探测器性能的影响

利用分子束外延设备(MBE)制备了MgZnO薄膜.X射线衍射谱、紫外-可见透射光谱和X射线能谱表明薄膜具有单一六角相结构,吸收边为340 nm,Zn/Mg组分比为62:38.采用掩膜方法使用离子溅射设备,在MgZnO薄膜上制备了Au电极,并实现了Au-MgZnO-Au结构的紫外探测器.通过改变溅射时间,得到具有不同Au电极厚度的MgZnO紫外探测器.研究结果表明:随着Au电极厚度的增加,导电性先缓慢增加,再迅速增加,最后缓慢增加并趋于饱和;而Au电极的透光率则随厚度的增加呈线性下降.此外,随着Au电极厚度的增加,器件光响应度先逐渐增大,在Au电极厚度为28 nm时达到峰值,之后逐渐减小.     

基于酞菁铜的有机光敏场效应管

制备了基于酞菁铜(CuPc)的有机光敏场效应晶体管,对器件的光敏特性进行了研究。实验结果表明,基于金源漏电极的器件,在波长655 nm,光强100 mW/cm²的光照下,明/暗电流比约为0.4,光响应度约为2.55 mA/W;而铝为源漏电极的器件,可以获得高达10⁴的明/暗电流比,但光响应度降低为0.39 mA/W。     

多环类苝四甲酸二酐插入层对ZnO纳米棒和聚合物复合太阳电池性能的影响

以ZnO纳米棒和聚[2-甲氧基-5-(2-乙基-己氧基)-1,4-苯撑乙烯撑](MEH-PPV)的复合体系作为光敏层制备了太阳电池.为了增大电池的光吸收,在ZnO纳米棒与MEH-PPV之间插入了有机n型小分子多环类苝四甲酸二酐(PTCDA),制备了不同厚度的PTCDA、结构为ITO/ZnO纳米棒/PTCDA/MEH-PPV/Au的太阳电池.实验发现,插入PTCDA后,电池在可见光区的吸收增强,光生激子数量增大,光电流密度增大.当蒸镀的PTCDA厚度为40 nm时,薄膜的粗糙度适中,表面形貌较为平滑,器件性 关键词： 有机太阳电池 ZnO纳米棒 聚合物     

基于立方相MgZnO薄膜的高响应度深紫外探测器

在超过相变临界厚度的立方相Mg0.29Zn0.71O薄膜上制备了Au插指电极MSM结构探测器件,30 V偏压下的峰值响应度可达27.9 A/W(268 nm),对应的外量子效率为12900%。分析认为原位生长在立方相MgZnO薄膜上的极薄的结构相变层引入了高密度的界面态,在立方相薄膜表面电极接触中起到了降低势垒、减小耗尽层宽度、增强电极注入电子的能力的作用,使得器件形成高的光导增益。     

ZnO/Ag/ZnO多层结构薄膜的光电性质

通过磁控溅射方法生长了不同银层厚度的ZnO/Ag/ZnO多层结构的薄膜,并对其形貌、光吸收谱、光致发光和光响应特性进行了比较研究.结果表明ZnO薄膜中银薄层的加入使得光致发光的强度增强.银层厚度为6 nm样品制成的器件在350 nm处的光响应度为0.06 A/W,相对于ZnO薄膜提高了一个数量级.而当银层厚度达到15 ...     

基于MoO_3/Au/MoO_3透明电极的有机太阳能电池

以透明导电薄膜Mo O3/Au/Mo O3代替铟锡氧化物(ITO)作为有机太阳能电池(OSCs)的阳极,研究了一系列结构为Mo O3/Au/Mo O3的透明电极和Mo O3(y nm)/Au(x nm)/Mo O3(y nm)/Cu Pc(25 nm)/C60(40nm)/BCP(8 nm)/Al(100 nm)的有机太阳能电池。研究表明,Mo O3/Au/Mo O3电极的光电特性可通过改变各层薄膜厚度加以调控,在Mo O3薄膜厚度为40 nm、Au薄膜厚度为10 nm时性能最优,且以该薄膜为电极的有机太阳能电池器件的性能接近于电极为ITO的有机太阳能电池器件。     

基于PBDT-TT-F∶PCBM体异质结红光探测器的光电特性

采用旋涂工艺与蒸镀工艺结合的方法制备了PBDT-TT-F∶PCBM体异质结红光探测器,研究了活性层的混合比例和厚度、退火温度等因素对器件光电特性的影响。实验结果表明:活性层PBDT-TT-F∶PCBM的混合质量比为1∶1.5、厚度为150 nm、退火温度为100℃、时间为15 min时制备的器件性能最佳,在波长为650nm、功率为6.6 m W/cm~2的光照下,探测器光电流密度可达到0.85 m A/cm~2,光响应度达到128 m A/W。     

飞秒激光微构造硅光电二极管的光电响应

在一定条件SF6气体氛围中,硅可在飞秒激光辐照区产生m量级的尖峰结构。针对不同尖峰高度的微构造硅,在不同温度下退火,采用电子蒸发的方法在正反面分别镀上铝电极,制备出了飞秒激光微构造光电二极管,并测试了其光电响应。实验结果表明:飞秒激光微构造光电二极管的响应随微构造硅光电二极管的尖峰高度和退火温度的不同而不同。尖峰高度为3～4 m的样品在973 K温度退火30 min后,响应度可达0.55 A/W。即使在1100 nm波长处,这种新型的硅光电二极管的响应仍可高达0.4 A/W。     

电极间距对ZnO基MSM紫外光电探测器性能的影响

利用金属有机物化学气相沉积法在蓝宝石衬底上制备了ZnO薄膜。利用Au电极,在ZnO薄膜上制备电极间距不同的金属-半导体-金属结构紫外光电探测器。发现随着电极间距从150μm降至5μm,探测器响应度呈现出从15 mA/W到75 mA/W的明显提高。同时,随着电极间距的减小,器件的I-V曲线线形发生了显著改变。这被归结为电极间距变化改变了器件耗尽区宽度和电极间电阻造成的结果。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.