基于气相沉积等离激元纳米粒子/三维石墨烯-镍泡沫复合结构的高灵敏度表面增强拉曼检测

本文提出一种基于气相沉积银纳米粒子和三维石墨烯-镍泡沫的复合等离激元结构.该结构是利用气相纳米团簇束流技术将高密度的银纳米粒子直接沉积于三维石墨烯-镍泡沫的表面制备而成.与传统银纳米结构相比,复合三维等离激元纳米结构具有"热点"数量多,局域场更强的特点,可作为基于表面增强拉曼技术的高灵敏度化学传感器.拉曼测试实验结果表明,该三维纳米结构在表面增强拉曼检测中可获得灵敏度高,重复性好的探针拉曼信号.通过进一步的理论模拟,发现该三维等离激元结构中增强的拉曼信号主要归因于纳米粒子与纳米粒子之间以及纳米粒子与石墨烯-镍泡沫衬底之间的多重近场耦合效应.     

径向偏振光激发氧化石墨烯/金纳米棒复合基底的表面增强拉曼散射性能

探究径向偏振矢量光与氧化石墨烯/金纳米棒复合结构的相互作用,以提高表面增强拉曼散射性能。基于FDTD Solutions软件,得到氧化石墨烯/单金纳米棒复合基底在径向偏振光激发下的表面增强拉曼散射增强因子达到10~8,比相同条件下线偏振光激发的大6个数量级。这种性能提高的物理机制源于径向偏振光激发金纳米棒的电磁增强与氧化石墨烯产生的本征化学增强。进一步详细讨论了径向偏振光激发下氧化石墨烯厚度、金纳米棒数量和排列方式对表面增强拉曼散射性能的影响。基于径向矢量光场激发多功能基底的表面增强拉曼散射性能调控在生物化学、食品安全与传感检测等领域具有巨大的应用潜力。     

氧化石墨烯负载金纳米颗粒SERS活性基底的制备与研究

本文采用湿化学方法制备具有表面增强拉曼散射活性的氧化石墨烯负载纳米金溶胶:通过以柠檬酸三钠为还原剂,在没有稳定剂、温和的液相反应条件下,同时还原氯金酸和深度氧化的石墨烯,原位制备氧化石墨烯负载金纳米颗粒复合物。利用紫外可见分光光度计、激光粒度分析仪、傅里叶变换红外吸收光谱仪、透射电子显微镜对所制得的氧化石墨烯负载金纳米颗粒复合物进行了表征和分析,并且采用拉曼光谱研究其作为增强试剂的性能。结果表明:所得溶胶在波长为540nm左右存在较强的吸收峰,粒径分布在50nm附近范围内;生成的金纳米粒子的大小及其分布受氯金酸用量的影响,并且粒径分布均匀,金纳米颗粒的平均尺寸为20nm,大量金纳米颗粒均匀地附着在氧化石墨烯的片层之间;氧化石墨烯的含氧官能团大幅降低,氧化石墨烯表面基团大部分被还原;以R6G为探针分子验证其拉曼增强效应,在浓度低至10nmol/L时依然具有较强的拉曼信号,增强因子达到2.4×10~5。所以高分散性、高稳定性的氧化石墨烯负载金颗粒溶胶,可作为SERS活性基底(增强试剂),用于快速检测。     

基于气相沉积等离激元纳米粒子/三维石墨烯-镍泡沫复合结构的高灵敏度表面增强拉曼检测（英文）

本文提出一种基于气相沉积银纳米粒子和三维石墨烯-镍泡沫的复合等离激元结构.该结构是利用气相纳米团簇束流技术将高密度的银纳米粒子直接沉积于三维石墨烯-镍泡沫的表面制备而成.与传统银纳米结构相比,复合三维等离激元纳米结构具有"热点"数量多,局域场更强的特点,可作为基于表面增强拉曼技术的高灵敏度化学传感器.拉曼测试实验结果表明,该三维纳米结构在表面增强拉曼检测中可获得灵敏度高,重复性好的探针拉曼信号.通过进一步的理论模拟,发现该三维等离激元结构中增强的拉曼信号主要归因于纳米粒子与纳米粒子之间以及纳米粒子与石墨烯-镍泡沫衬底之间的多重近场耦合效应.     

金银纳米粒子的电化学性质及联苯胺的SERS研究

采用柠檬酸钠还原氯金酸,硼氢化钠还原硝酸银分别制备了较小粒径的金、银纳米粒子。运用紫外可见吸收光谱(UV-Vis)、扫描电子显微镜(SEM)、循环伏安法(CV)对金、银纳米粒子进行了表征。结果表明：所得金、银纳米粒子粒径分别约为16和10 nm,并能以亚单层形式组装于导电玻璃(ITO)表面;CV图显示金、银纳米粒子分别有一对不对称的氧化还原峰,而且纳米粒子的浓度对其氧化还原电位存在一定的影响。采用自组装方法,以联苯胺为偶联分子, 在粗糙金基底表面构筑了金/银纳米粒子的双层有序结构。表面增强拉曼光谱研究表明, 在有序金银纳米粒子组装体中偶联分子的拉曼散射得到了增强。     

用于低丰度添加剂检测的具有表面增强拉曼光谱活性的Au@Au@Ag双壳核纳米粒子的制备

本文合成了Au@Au@Ag双壳核纳米粒子,并利用透射电子显微镜、扫描电子显微镜和紫外可见光谱进行了表征. 以结晶紫作为拉曼探针,并与相同方法制备的Au、Au@Ag和Au@Au核壳纳米粒子比较,发现其表面增强拉曼光谱活性明显增强. 通过引入氯化钠,发现所得材料的表面增强拉曼光谱活性进一步增强,氯化钠浓度在表面增强拉曼光谱检测中起着关键作用. 在适当的氯化钠浓度下,检测限可低至10^-10 mol/L,并讨论了其中可能的增强机制. 通过简单的样品预处理,利用该材料作为基底可以检测辣椒粉中罗丹明B,检出限可达5 μg/g. 该研究表明Au@Au@Ag 双壳核纳米粒子在检测低浓度非法食品添加剂方面具有潜在用途.     

纳米Ag材料表面等离子体激元引起的表面增强拉曼散射光谱研究

用热蒸发的方法制备了纳米Ag材料,并用扫描电子显微镜对纳米粒子进行了形貌的表征,通过紫外—可见分光光度计得到Ag纳米粒子的透过谱,得到了Ag纳米粒子的表面等离子体共振的峰值位置.以罗丹明6G为探针分子测定Ag纳米粒子衬底的表面增强拉曼散射效应,通过拉曼散射光谱与透过谱研究了由表面等离子体激元的强极化场引起的表面增强拉曼散射效应,结合透过谱与拉曼增益因子提出了一种描述表面等离子体光学和电学特性的方法,并结合扫描电镜的结果给出了不同结构的纳米Ag材料对表面等离子体激元强度的影响. 关键词： 热蒸发 纳米Ag材料 表面等离子体 表面增强拉曼散射     

不同粒径、超均匀球形金纳米粒子合成及其表面增强拉曼散射效应研究

以氯金酸为原料,抗坏血酸为还原剂,柠檬酸钠为保护剂,用化学还原(种子生长)法制备了不同粒径、超均匀的球形金纳米粒子溶胶,并通过紫外可见吸收光谱(UV-Vis)和扫描电子显微镜(SEM)进行表征。结果表明,随着金纳米粒子粒径的增大,其UV-Vis光谱中的吸收峰发生红移并出现四极峰。为进一步研究金纳米粒子表面增强拉曼散射(SERS)效应的作用机理并优化其灵敏度,我们以罗丹明6G(R6G)为探针分子,对不同粒径的金纳米粒子进行SERS表征,发现R6G的SERS信号随着金纳米粒子的增大先增强后减弱。当金纳米粒子的平均粒径达到120 nm时,产生最强SERS信号增强,增强因子约为1.1×107。三维时域有限差分法(3D-FDTD)理论模拟纳米粒子阵列电磁场分布结果与实验数据的趋势一致。     

TiO_2/石墨烯/Ag复合结构SERS实验

基于氧化物半导体的光催化特性,能够降解有机物分子,使表面增强拉曼散射基底得以重复使用。提出了银纳米颗粒有效修饰覆盖有石墨烯的二氧化钛纳米棒阵列(TiO_2/石墨烯/Ag)复合结构作为表面增强拉曼散射基底,并对其进行了实验研究。利用水热法制备了二氧化钛纳米棒阵列;采用湿法转移石墨烯和光照还原方法制备了TiO_2/石墨烯/Ag复合结构。用罗丹明6G(R6G)分子作为探测分子,结果表明:随着紫外光照沉积时间增加,探针分子的拉曼信号先增强后减弱;计算得到最大增强因子值约为2.6×106。此外,还对TiO_2/石墨烯/Ag复合结构的紫外自清洁特性进行了初步实验,结果表明,紫外光照射20min后,其拉曼强度下降到42.3%,具有一定的紫外清洁效果。     

基于“热点”效应的表面增强拉曼散射光谱研究

本文利用罗丹明6G在银胶体粒子聚集点上的表面增强拉曼光谱的强度变化,采用逐点扫描获得拉曼光谱的"Mapping"方法,获得了不同的银胶体粒子聚集点对吸附的R6G表面增强拉曼光谱强度的影响。分析了"热点"对拉曼散射的增强的作用,表明"热点"的增强强度和纳米粒子的聚集程度有关。     

Reduction of silver nanoparticles onto graphene oxide nanosheets with <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethylformamide and SERS activities of GO/Ag composites

Silver nanoparticles (Ag NPs) have been homogeneously deposited onto graphene oxide (GO) nanosheets by an optimal method, in which N,N-dimethylformamide (DMF) as a co-dispersant of GO and reductant of sliver ions is added to an aqueous suspension of GO and AgNO₃. GO nanosheets are uniformly covered by Ag NPs with a narrow size distribution and inter-particle gap. Raman signals of GO are greatly enhanced after deposition owing to the charge transfer interaction of GO with Ag NPs. The GO/Ag composite can be further utilized as an effective surface-enhanced Raman scattering (SERS) active substrate. Several new Raman bands and frequency shifts are clearly observed in using 4-aminothiophenol (4-ATP) as a Raman probe on GO/Ag compared to the normal Raman spectrum of solid 4-ATP. The Raman enhancement arises from a major electromagnetic effect and a minor chemical effect.     

Elucidating synthesis of noble metal nanoparticles/graphene oxide in free-scavenger γ-irradiation

Three representative noble metal (Ag, Au and Pt) nanoparticles decorated graphene oxide (NMNPs/GO) composites were fabricated via γ-irradiation without scavenger. The NMNPs/GO composites exhibited the pure and well-dispersed particles structure, which directly illustrated that the GO could be acted as scavenger to benefit reduction and growth of NMNPs. Compared with irradiated GO (IGO), the GO substrate of composites had the lower relative content of hydroxyl groups, meanwhile, the relative contents of carbonyl groups (Pt > Au > Ag) were increased with increasing valence of noble metal. Such results illustrated that the abundant hydroxyl groups could convert the hydrated electrons, hydroxyl and hydrogen radicals to promote the growth of NMNPs on the surface of GO. In addition, the Raman signals of Ag NPs/GO composites were significantly enhanced (6.18 fold more than pristine GO, respectively), exhibiting obvious surface-enhanced Raman scattering activity. Therefore, this paper revealed that the GO could convert the hydrated electrons and radicals to synthetizing NMNPs/GO composites during γ-ray irradiation.     

Surface‐enhanced Raman scattering of silylated graphite oxide sheets sandwiched between colloidal silver nanoparticles and silver piece

Graphite oxide (GO) was successfully silylated by 3‐mercaptopropyltrimethoxysilane. The surface‐enhanced Raman scattering spectrum of the silylated GO sheets sandwiched between colloidal silver nanoparticles and silver piece is presented. The Raman signal shows a 10⁴ enhancement compared to that of bulk GO. The large Raman enhancement is most likely a result of electromagnetic (EM) coupling between the colloidal silver nanoparticles (localized surface plasmon) and the silver piece (surface plasmon polariton), creating large localized EM fields at their interface, where the silylated GO sheets reside in this sandwich architecture. Copyright © 2009 John Wiley & Sons, Ltd.     

NiCoP/rGO复合材料的合成及其性能研究

以六水合氯化镍、七水合硫酸钴、氧化石墨烯(GO)和赤磷为原料,利用原位水热法,在不添加任何表面活性剂的情况下,合成了磷化钴镍/还原氧化石墨烯(NiCoP/rGO)纳米复合材料,并通过XRD、SEM、TEM、IR、Raman等对该复合材料进行了表征.结果表明,所得复合材料由NiCoP纳米颗粒和还原氧化石墨烯片层结构组成,NiCoP纳米颗粒尺寸大约为20 nm,均匀分布在rGO片层结构表面上,同时探讨了复合材料的形成过程.另外,复合材料的吸附脱除实验表明,所得复合材料对多种染料都具有非常好的吸附作用,因此,在污水处理方面有较大的应用价值.     

pH‐dependent surface‐enhanced Raman scattering of aromatic molecules on graphene oxide

Graphene has become an ideal substrate for surface‐enhanced Raman scattering (SERS) to study the chemical enhancement mechanism. In comparison with mechanically exfoliated graphene, graphene oxide (GO) has been found to be a better substrate due to its highly negatively charged oxygen functional groups. In this work, the pH‐dependent SERS effect of aromatic molecules on GO are investigated. The results demonstrate that the Raman enhancement of dyes deposited on GO performs differently over a wide range of pH values (2 to 10). Adsorption experiments show that the pH‐dependent SERS effect is closely related to the adsorption of aromatic molecules on GO, which is dominated by the electrostatic interaction. Thus, the influence of pH in GO‐mediated SERS should be carefully considered, especially in its biomedical application. Copyright © 2012 John Wiley & Sons, Ltd.     

Preparation and electrochemical properties of LiFePO<Subscript>4</Subscript>/graphene composites from tailoring graphene oxides

LiFePO₄/graphene composites have been prepared by using tailoring graphene oxide (GO) nanosheets as precursors. The structure and electrochemical properties of the composites were investigated by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), Raman microscopy, and a variety of electrochemical testing techniques. The decrease in graphene size reduces the contact resistance between activated materials, and enhances the lithium-ion transport in LiFePO₄/graphene composites. With low weight fractions of small-size graphene sheets, the composites show better electrochemical performance than those with large size graphene sheets.     

Self-assembly of metal–organic frameworks and graphene oxide as precursors for lithium-ion battery applications

We fabricated composites of Fe₂O₃/reduced graphene oxide as lithium-ion batteries anode material with controlled structures by employing self-assembly of metal–organic frameworks (MOFs) and polymer-functionalized graphene oxide as precursors. By electrostatic interaction, the negatively charged MOFs, Prussian Blue (PB), are assembled on poly(diallyldimethylammonium chloride) (PDDA)-functionalized graphene oxide (positive charge). Then the PB cubes become FeOOH nanosheets when treated with sodium hydroxide. Upon further annealing, the FeOOH nanosheets transform to Fe₂O₃ nanoparticles while the graphene oxide become reduced graphene oxide simultaneously. It was found that the composites have good performance as anode of lithium-ion battery. This work shows a new way for self-assembling MOFs and 2D materials.     

退火法制备石墨烯-银纳米粒子及其增强拉曼实验

针对目前SERS基底上金属颗粒制备过程中存在的分布不均匀、易氧化和稳定性差等缺点,通过热蒸镀和高温退火获得分布均匀的SERS基底;同时结合石墨烯优良的光学性能、化学惰性、荧光猝灭以及本身的SERS增强等优点,制备了稳定的石墨烯-银纳米颗粒（GE/AgNPs）复合结构SERS基底。通过GE/AgNPs复合结构的拉曼光谱稳定性试验证明了石墨烯在GE/AgNPs结构中起到隔绝银纳米颗粒与空气直接接触及催化氧化银脱氧的作用,有利于SERS基底的时间稳定性。(1) 石墨烯、Ag纳米颗粒及其复合结构的制备。首先采用热蒸镀和高温退火的方法使Ag纳米颗粒均匀地沉积在SiO₂/Si基底上,再采用化学气相沉积法在Cu箔上制备少层石墨烯,并用湿法转移法将石墨烯转移到目标基底上,并实验研究了以不同的退火顺序对GE/AgNPs基底造成的影响。(2) 石墨烯、Ag纳米颗粒及其复合基底的表征。分别采用光学显微镜、扫描电子显微镜和拉曼光谱进行表征,得到转移后的纯石墨烯较完整地覆盖在SiO₂/Si基底上面,表面比较平整,但在少数地方仍然存在褶皱和杂质;SEM表征结果表明对于不同制备流程的GE/AgNPs复合结构上的Ag纳米颗粒基本呈球形。基本符合Ostwald熟化理论,通过对退火温度和时间的控制能获得平均粒径在40~60 nm的银颗粒,且分布较均匀。此外,在不同退火顺序中,石墨烯的加入对银纳米颗粒的扩散形成扩散势垒,从而出现较大的不规则的颗粒。(3) 基底稳定性试验和仿真分析。通过基底本身的Raman mapping测试,分析了石墨烯拉曼特征峰峰值和半高宽的变化,得知基底对石墨烯本身的拉曼增强效果主要来源于银纳米颗粒间的电磁场增强。同时采用浓度为10-6 mol·L-1的罗丹明6G (R6G)水溶液作为探针分子,对转移了石墨烯的GE/AgNPs复合基底和未转移石墨烯的Ag纳米颗粒基底进行了SERS稳定性实验。结果表明GE/AgNPs复合基底在1~33 d内衰减较缓慢,30 d后仍能探测到拉曼信号约为原来信号的35.1%~40.6%;而纯Ag基底上随着Ag纳米颗粒在空气中迅速氧化,基底的SERS性能显著下降,在30 d后只有原来信号的5.9%~11.3%。此外,通过实验得到覆盖了石墨烯之后的增强因子约为6.05×105。最后采用时域有限差分算法（FDTD）计算了复合结构的电磁场分布和理论增强因子,其理论增强因子可以达到5.7×105。实验和仿真结果的差异,主要是源于石墨烯的化学增强作用。     

Preparation of graphene-glass fiber-resin composites and its electromagnetic shielding performance

The surface of the glass fiber (GF) was modified by silane coupling agent (KH550) and bovine serum albumin (BSA), and then the graphene oxide (GO) was coated onto the modified surface of the glass fiber. Followed by a reduction reaction, the reduced graphene oxide (RGO) coated on glass fiber was obtained. Finally, the reduced graphene oxide-glass fibers (RGO-GF) were combined with unsaturated resins. The interfacial morphology of reduced graphene oxide-glass fibers was investigated by scanning electron microscopy (SEM). The structure of the materials was analyzed by Fourier transform infrared spectroscopy (FT-IR). The crystal phases of the material were identified by X - ray diffraction (XRD). The mechanical properties and electromagnetic shielding effectiveness of the sample were tested. The results showed that the interface between glass fibers and graphene binds more closely after the glass fibers was treated by KH550. The tensile strength of the RGO-GF composites reached 85.05 MPa. Compared with the GF composites, it increased by 51.4% when the glass fibers content was 30%. The shielding effectiveness of the composites reached 21.3 dB at the frequency range of 8.2–12.4 GHz (x-band). Therefore, by coating the surface with reduced graphene oxide, the glass fibers can make a great shielding effect on the electromagnetic wave.