基于气相沉积等离激元纳米粒子/三维石墨烯-镍泡沫复合结构的高灵敏度表面增强拉曼检测（英文）

本文提出一种基于气相沉积银纳米粒子和三维石墨烯-镍泡沫的复合等离激元结构.该结构是利用气相纳米团簇束流技术将高密度的银纳米粒子直接沉积于三维石墨烯-镍泡沫的表面制备而成.与传统银纳米结构相比,复合三维等离激元纳米结构具有"热点"数量多,局域场更强的特点,可作为基于表面增强拉曼技术的高灵敏度化学传感器.拉曼测试实验结果表明,该三维纳米结构在表面增强拉曼检测中可获得灵敏度高,重复性好的探针拉曼信号.通过进一步的理论模拟,发现该三维等离激元结构中增强的拉曼信号主要归因于纳米粒子与纳米粒子之间以及纳米粒子与石墨烯-镍泡沫衬底之间的多重近场耦合效应.     

界面自组装的金/氧化石墨烯复合材料的表面增强拉曼散射行为研究

采用Frens法制备金纳米粒子溶胶,通过界面自组装技术在掺磷的非晶碳衬底表面构筑三维的金/氧化石墨烯/金复合结构.以罗丹明B为探针分子,考察金/氧化石墨烯/金复合材料的表面增强拉曼散射活性.结果表明,由于氧化石墨烯的化学增强和金纳米粒子的电磁场增强的协同作用,在该三维复合材料上获得了很强的罗丹明B拉曼信号.所设计的三维金/氧化石墨烯/金复合材料在生物分析、环境监测、疾病防控、食品安全等领域具有潜在的应用价值.     

银纳米颗粒阵列的表面增强拉曼散射效应研究

利用具有高密度拉曼热点的金属纳米结构作为表面增强拉曼散射(SERS)基底,可以显著增强吸附分子的拉曼信号.本文通过阳极氧化铝模板辅助电化学法沉积制备了高密度银(Ag)纳米颗粒阵列;利用扫描电子显微镜和反射谱表征了样品的结构形貌和表面等离激元特性;用1, 4-苯二硫醇(1, 4-BDT)为拉曼探针分子,研究了Ag纳米颗粒阵列的SERS效应.通过优化沉积时间,制备出高SERS探测灵敏度的Ag纳米颗粒阵列,检测极限可达10~(-13)mol/L;时域有限差分法模拟结果证实了纳米颗粒间存在强的等离激元耦合作用,且发现纳米颗粒底端的局域场增强更大.研究结果表明Ag纳米颗粒阵列可作为高效的SERS基底.     

银纳米粒子修饰三维碳纳米管阵列SERS实验

为了使表面增强拉曼散射(SERS)基底的三维聚焦体积内包含更多的“热点”,能吸附更多探针分子和金属纳米颗粒,以便获得更强的拉曼光谱信号,提出了银纳米粒子修饰垂直排列的碳纳米管阵列三维复合结构作为SERS基底,并对其进行了实验研究。利用化学气相沉积(CVD)方法制备了垂直排列的碳纳米管阵列;采用磁控溅射镀膜方法先在碳纳米管阵列上形成一层银膜,再通过设置不同的高温退火温度,使不同粒径的银纳米粒子沉积在垂直有序排列碳纳米管阵列的表面和外壁。SEM结果表明：在有序碳纳米管阵列的表面和外壁都均匀地负载了大量银纳米粒子,并且银纳米颗粒的粒径、形貌及颗粒间的间距随退火温度的不同而不同。采用罗丹明6G(R6G)分子作为探针分子,拉曼实验结果表明：R6G浓度越高,拉曼强度越强,但是R6G浓度的增加与拉曼强度增强并不呈线性变化;退火温度为450 ℃,银纳米颗粒平均粒径在100～120 nm左右,退火温度为400 ℃,银纳米颗粒平均粒径在70 nm左右,退火温度为450 ℃的拉曼信号强度优于退火温度400和350 ℃。     

TiO_2/石墨烯/Ag复合结构SERS实验

基于氧化物半导体的光催化特性,能够降解有机物分子,使表面增强拉曼散射基底得以重复使用。提出了银纳米颗粒有效修饰覆盖有石墨烯的二氧化钛纳米棒阵列(TiO_2/石墨烯/Ag)复合结构作为表面增强拉曼散射基底,并对其进行了实验研究。利用水热法制备了二氧化钛纳米棒阵列;采用湿法转移石墨烯和光照还原方法制备了TiO_2/石墨烯/Ag复合结构。用罗丹明6G(R6G)分子作为探测分子,结果表明:随着紫外光照沉积时间增加,探针分子的拉曼信号先增强后减弱;计算得到最大增强因子值约为2.6×106。此外,还对TiO_2/石墨烯/Ag复合结构的紫外自清洁特性进行了初步实验,结果表明,紫外光照射20min后,其拉曼强度下降到42.3%,具有一定的紫外清洁效果。     

贵金属纳米结构为敏感层的锥形光纤探针及其SERS活性

表面等离激元纳米结构与便携式光纤拉曼系统相结合,在液体样品和生物活体组织的快速、实时监测上有较好的应用前景。其核心技术是将具有表面增强拉曼散射(SERS)活性的贵金属纳米结构耦合到光纤探针表面。本文基于共价键结合原理,将3-巯丙基三甲氧基硅烷通过与锥形光纤探针表面的硅羟基形成共价键修饰在光纤上;同时,硅烷偶联剂末端的巯基与金或银纳米结构形成Au-S或Ag-S共价键,将金纳米粒子和银纳米立方体牢牢吸附到光纤探针表面。这种SERS光纤探针具有很高的稳定性(SERS信号相对标准偏差低于3%),对农残甲基对硫磷的敏感度达到10纳摩尔,对污染物的远程、便携式在线检测具有重要意义。     

纳米结构表面形貌成型机理及其对石墨烯拉曼光谱的影响

通过真空热蒸镀和高温退火法制备的金属纳米复结构SERS基底因其具有良好的灵敏度,稳定性和均匀性而广泛应用于各种检测领域。石墨烯具有优良的光学特性,化学惰性以及荧光猝灭效应,自被发现以后一直是光学微纳器件中的一大热门材料。石墨烯还可以有效分离探针分子与基底,优化拉曼光谱质量,因此广泛应用于SERS研究领域。同时石墨烯可以有效隔绝金属纳米结构与空气的直接接触防止金属纳米结构被氧化而失效,也可以催化氧化银的脱氧反应提升SERS基底的稳定性。在石墨烯/金属纳米复合结构SERS基底在制备过程中,受到金属膜的种类、厚度参数、气体种类、退火时间、温度和气压等因素的影响,制备的金属纳米结构形貌存在很大差异。石墨烯的拉曼光谱会因为应力和掺杂导致其拉曼特征峰出现不同程度的增强,移动以及展宽。（1）采用真空热蒸镀法和高温退火法制备石墨烯/银纳米复合结构SERS基底,建立了金属纳米颗粒成型机理的模型,从孔洞形成、孔洞生长、金属纳米岛形成三个阶段分析了金属纳米粒子的成型过程,实验沉积5,10,15以及20 nm的银薄膜,退火后银纳米结构的覆盖率分别为~35.1%,~24.4%,~30%以及~96.0%,在沉积银薄膜样品上使用湿法转移石墨烯,退火处理后发现石墨烯阻止了银纳米岛的形成过程;（2）理论分析了银薄膜厚度、石墨烯覆盖对复合结构的几何形貌、拉曼增强特性的影响,石墨烯由于其具有较高的杨氏模量和表面张力,可以有效抑制退火过程中银薄膜向纳米粒子转变的过程,从而实现对复合结构表面形貌的调控;（3）实验研究了银纳米粒结构形貌对石墨烯拉曼光谱的影响,并理论分析了蒸镀不同银薄膜厚度的样品对石墨烯的拉曼光谱增强,移动以及展宽影响的具体原因。     

金属亚波长结构的表面增强拉曼散射

灵敏度高、可重复性好的固态表面增强拉曼散射基板可作为生物医学、环境科学、化学化工、纳米科技等领域的生化感测器,具有十分重要的实际应用价值.传统的表面增强拉曼散射基于金属颗粒提供的局域表面等离谐振这一物理机制,但其组装不易且模式损耗大.本文基于周期性金属亚波长结构,构建增强拉曼散射信号的"热点",同时保证测量信号的可重复性.从表面光子能带结构出发,提出了区别于局域表面等离谐振的其他三种增强机制:表面等离子极化激元带边增强机制、间隙等离子极化激元增强机制以及二者相耦合增强机制.采用一定的工艺,提高金属表面平整度,抑制表面等离子极化激元的传播损耗,从而提高表面增强拉曼散射的增强因子.理论结合实验,且二者一致性好.研究结果有望将表面增强拉曼散射光谱技术进一步向实用化方向推进.     

表面等离激元调控化学反应

表面等离激元是金属与介质表面自由电子的集体振荡,能够突破衍射极限,将光束缚在纳米结构表面附近极小的空间内,为纳米尺度的光操控提供可能.利用表面等离激元共振,不仅可以增强局域表面电磁场强度,实现对表面附近分子荧光和拉曼信号的极大增强,而且等离激元弛豫诱导的热电子还可以调控表面分子的化学反应,提高反应速率和选择性,即等离激元调控(催化)化学反应.作为一种新型催化体系,等离激元催化已经实现了多种传统光催化中难以发生的化学反应,是表面等离激元领域的前沿热点问题.由于等离激元催化反应的复杂性与多样性,其反应动力学过程的完全表征和反应机理的揭示仍然是一个巨大的挑战.精确表征催化反应的中间及最终产物,获取反应动力学过程中更多的细节信息,对于探索等离激元催化机理,以及设计更为合理高效的催化体系极为重要.本文围绕等离激元催化的最新研究进展,总结并探讨等离激元催化中所使用的各种表征技术.首先,简单介绍了等离激元催化的基本概念和催化机理.其次,综述了拉曼光谱(包括表面/针尖增强拉曼光谱),在等离激元催化原位监测中的应用,并进一步详细介绍了气相色谱法、气相色谱-质谱联用、高效液相色谱法、扫描透射电子显微镜、扫描隧道显微镜、扫描电化学显微镜、紫外可见吸收光谱等技术在等离激元催化反应研究中的重要作用.最后,探讨了这些表征技术在等离激元催化动力学过程研究和催化机理探索中的特点与优势,并展望了等离激元催化及相关表征技术的发展与挑战.     

银纳米粒子自组装复合LB膜的结构与性质

纳米粒子的自组装和有序组装膜的结构与性质近年来受到了人们的广泛关注,纳米粒子的表面结构与性质对由其组装成的有序膜的结构与性质有直接的影响。文章报道了利用自组装技术制备的银纳米粒子与双亲有机分子的单层和多层复合LB膜,通过吸收光谱和表面增强拉曼光谱研究了银纳米粒子与吸附分子间的相互作用,探讨了复合膜的成膜特性及银纳米粒子的拉曼增强特性。十八胺/银粒子复合LB膜的吸收光谱及拉曼光谱显示,十八胺分子与银纳米粒子表面的活位通过NH₂中的氮原子以复合体的形式结合;同时,在激发光的作用下复合体可能存在光催化过程。根据银粒子复合LB膜的实验结果,十八胺和十八酸之间的反应产物在复合膜中起空间位阻作用,与银粒子表面的相互作用较弱。     

Self-assembly 2D plasmonic nanorice film for surface-enhanced Raman spectroscopy

As an ultrasensitive sensing technology, the application of surface enhanced Raman spectroscopy (SERS) is one interesting topic of nano-optics, which has huge application prospectives in plenty of research fields. In recent years, the bottleneck in SERS application could be the fabrication of SERS substrate with excellent enhancement. In this work, a two-dimensional (2D) Ag nanorice film is fabricated by self-assembly method as a SERS substrate. The collected SERS spectra of various molecules on this 2D plasmonic film demonstrate quantitative detection could be performed on this SERS substrate. The experiment data also demonstrate this 2D plasmonic film consisted of anisotropic nanostructures has no obvious SERS polarization dependence. The simulated electric field distribution points out the SERS enhancement comes from the surface plasmon coupling between nanorices. And the SERS signals is dominated by molecules adsorbed at different regions of nanorice surface at various wavelengths, which could be a good near IR SERS substrate for bioanalysis. Our work not only enlarges the surface plasmon properties of metal nanostructure, but also exhibits the good application prospect in SERS related fields.     

Research on the Raman properties of NiFe/cicada wing composite SERS platform modified by silver nanoparticles

Composite structures have been widely concerned in the preparation of surface enhanced Raman scattering (SERS) substrates. In this paper, by solving the problem that the magnetic material was difficult to glow in magnetron sputtering, ferro-nickel (NiFe) alloy was deposited on the cicada wing (CW) and the NiFe/CW substrate was obtained. The results of sliver nanoparticles (Ag NPs) modified on the substrate were subsequently compared, and the SERS properties of the new Ag/NiFe/CW substrate were analyzed. Obviously, the intensity of SERS signals has been greatly improved after the modification of Ag NPs, and the substrate exhibits excellent reproducibility. The Ag NPs modified substrates were also applied to the detection of toxic crystal violet (CV) solution, which showed remarkable SERS activity. It has been proved that the strategy of modifying Ag NPs on the substrate to form a composite structure has great potential for improving the SERS performance of the substrate.     

Nanogaps in 2D Ag‐nanocap arrays for surface‐enhanced Raman scattering

The surface‐enhanced Raman scattering substrate of Ag–Ag nanocap arrays are prepared by depositing Ag film onto two‐dimensional (2D) polystyrene colloidal nanosphere templates. When the original colloidal arrays are used as the substrate for Ag deposition, surface‐enhanced Raman scattering (SERS) enhancements show the strong size‐dependence behaviours. When O₂‐plasma etched 2D polystyrene templates are used as the substrate for Ag deposition to form nanogaps, the gap sizes between adjacent Ag nanocaps from 5 to 20 nm generate even greater SERS enhancements. When SiO₂ coverage is deposited to isolate the Ag nanocaps from the neighbours, the SERS signals are enhanced more. The significant SERS effects are due to the coupling between Ag nanocaps controlled by the distance, which enhances the local electric‐field intensity. Copyright © 2013 John Wiley & Sons, Ltd.     

Reduction of silver nanoparticles onto graphene oxide nanosheets with <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethylformamide and SERS activities of GO/Ag composites

Silver nanoparticles (Ag NPs) have been homogeneously deposited onto graphene oxide (GO) nanosheets by an optimal method, in which N,N-dimethylformamide (DMF) as a co-dispersant of GO and reductant of sliver ions is added to an aqueous suspension of GO and AgNO₃. GO nanosheets are uniformly covered by Ag NPs with a narrow size distribution and inter-particle gap. Raman signals of GO are greatly enhanced after deposition owing to the charge transfer interaction of GO with Ag NPs. The GO/Ag composite can be further utilized as an effective surface-enhanced Raman scattering (SERS) active substrate. Several new Raman bands and frequency shifts are clearly observed in using 4-aminothiophenol (4-ATP) as a Raman probe on GO/Ag compared to the normal Raman spectrum of solid 4-ATP. The Raman enhancement arises from a major electromagnetic effect and a minor chemical effect.     

SERS study of Ag nanoparticles electrodeposited on patterned TiO2 nanotube films

In this work, Ag nanoparticles (NPs) were deposited on patterned TiO₂ nanotube films through pulse‐current (PC) electrodeposition, and as a result patterned Ag NPs films were achieved. Scanning electron microscopy (SEM), electron probe microanalysis (EPMA), and X‐ray diffraction (XRD) were used, respectively, to study the morphology, uniformity, and phase structure of the patterned Ag NP films. The size and density of the as‐deposited Ag NPs could be controlled by changing the deposition charge density, and it was found that the patterned Ag NP films produced under a charge density of 2.0 C cm⁻² gave intense UV–vis and Raman peaks. Two‐dimensional surface‐enhanced Raman scattering (SERS) mapping of rhodamine 6G (R6G) on the patterned Ag NP films demonstrated a high‐throughput, localized molecular adsorption and micropatterned SERS effect. Copyright © 2010 John Wiley & Sons, Ltd.     

Ultrathin silver‐coated gold nanoparticles as suitable substrate for surface‐enhanced Raman scattering

Surface‐enhanced Raman scattering (SERS) is an extremely powerful tool for the analysis of the composition of bimetallic nanoparticle (BNP) surfaces because of the different adsorption schemes adopted by several molecules on different metals, such as Au and Ag. The preparation of BNPs normally implies a change in the plasmonic properties of the core metal. However, for technological applications it could be interesting to synthesize core–shell structures preserving these original plasmonic properties. In this work, we present a facile method for coating colloidal gold nanoparticles (NPs) in solution with a very thin shell of silver. The resulting bimetallic Au@Ag system maintains the optical properties of gold but shows the chemical surface affinity of silver. The effectiveness of the coating method, as well as the progressive silver enrichment of the outermost part of the Au NPs, has been monitored through the SERS spectra of several species (chloride, luteolin, thiophenol and lucigenin), which show different behaviors on gold and silver surfaces. A growth mechanism of the Ag shell is proposed on the basis of the spectroscopic and microscopic data consisting in the formation and deposit of Ag clusters on the Au NP surface. Copyright © 2009 John Wiley & Sons, Ltd.     

Induced SERS activity in Ag@SiO2/Ag core‐shell nanosphere arrays with tunable interior insulator

In this work, we demonstrated a bottom‐up growth of Ag@SiO₂/Ag core‐shell nanosphere arrays with tunable SiO₂ interior insulator and the optimized surface‐enhanced Raman scattering (SERS) substrate based on a nanostructure performed with both high sensitivity and large‐area uniformity. Their morphological, structural, and optical properties were characterized, and the induced SERS activities were investigated theoretically by the FDTD simulation and experimentally using analyte molecules. An ultrathin SiO₂ shell with tunable thickness can be synthesized pinhole‐free by a chemical vapor deposition, working as an interior insulator between the Ag core and Ag out‐layer coating. A detection limit as low as 10⁻¹² M and an enhancement factor up to 3 × 10⁷ were obtained, and the SERS signal was highly reproducible with small standard deviation. The method opened up a way to create a new class of SERS activity sensor with high‐density ‘hot spots’, and it may play an important role in device design and the corresponding biological and food safety monitoring applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Silver‐decorated carbon nanotube networks as SERS substrates

We report on investigations upon a surface‐enhanced Raman scattering (SERS) substrate produced from a two‐dimensional single‐walled carbon nanotube (SWNT) network decorated with Ag nanoparticles. Using the strong and unique Raman spectrum of SWNTs as a reference, the SWNT/Ag nanostructure can be considered to provide two regions: one with an ultrasensitive SERS response for single‐molecule SERS (SMSERS) study; and another with uniform SERS enhancement over an area of several square millimeters for general SERS measurements. We report the appearance of an anomalous Raman feature at around 2180 cm⁻¹ in the high‐sensitivity region which exhibits the characteristics of SMSERS. The SERS performance of the uniform area was characterized using pyridine vapor adsorbed onto the substrate. The presence of the SWNT/Ag nanostructure enhanced the Raman intensity by over seven orders of magnitude, a factor comparable to or exceeding that obtained on SERS substrates reported by other groups. The results indicate great potential to produce highly sensitive, uniform SERS substrates via further fine‐tuning of the nanostructure. Copyright © 2011 John Wiley & Sons, Ltd.     

SHINERS and plasmonic properties of Au Core SiO2 shell nanoparticles with optimal core size and shell thickness

Shell‐isolated nanoparticles (NPs)‐enhanced Raman spectroscopy (SHINERS) can be potentially applied to virtually any substrate type and morphology. How to take a step forward to prepare SHINERS NPs (SHINs) with superior performance is critical for the practical applications of surface‐enhanced Raman scattering (SERS) in the breadth and depth. Here, we present a method to obtain 120 nm diameter gold NPs coated with ultrathin silica shells (1–4 nm). The silica shell can be controlled growth through carefully tuning a series of parameters, such as amount of 3‐aminopropyl triethoxysilane used, pH, reaction time, and reaction temperature. We compare the enhancement factor of the obtained 120 nm Au with a 4 nm silica shell NPs to the 55 nm Au with a 4 nm silica shell NPs, and the activity of a 120 nm SHINs is nearly 24 times that the 55 nm SHIN from a single particle view. We also compare the enhancement factor of 1 nm silica shell Au@SiO₂ NPs with the bare Au NPs. The enhancement factor of 1 nm silica shell Au@SiO₂ NPs was found to be about twice that of the bare particles. For a deeper understanding of the source of the giant enhanced electrical field of the 1 nm silica shell Au@SiO₂ NPs, we study the plasmonic property of single 1 nm silica shell Au@SiO₂ NP on a gold film substrate through correlation of the structure of single NP using SEM with its SPR spectroscopy. We find that the multipolar interaction between the single Au@SiO₂ NP and gold film substrate is important for the SERS. Our studies on the performance of 120 nm SHINs and the plasmonic property of these particles can significantly expand the applications of SHINERS technique and improve the understanding of physical nature of SHINs. Copyright © 2013 John Wiley & Sons, Ltd.     

PS微球阵列的制备与表面增强拉曼散射研究

为了研究不同直径PS微球(表面溅射Ag膜)基底的表面增强拉曼散射(SERS)效应,制造了一个新的表面增强拉曼散射(SERS)基底。通过在n型(100)单晶硅片上采用旋涂的方法,得到不同直径的呈六角形有序排列的单层PS微球阵列,然后在PS微球阵列表面磁控溅射一层约30 nm的Ag膜。利用拉曼光谱仪以罗丹明R6G为探针进行了SERS光谱测定,分析比较了不同直径PS微球阵列的表面增强拉曼散射效应,结果表明,溅射有Ag膜的PS微球基底在不同直径下均有不同程度的SERS效应。随着微球直径的增加,PS微球阵列的起伏程度不断加强(粗糙度不断增加),SERS信号逐渐增强,当球直径达到600 nm时,峰的增强信号达到最大,进而获得了一个最优化的SERS基底。同时发现在基底上获得了高信噪比的R6G的SERS光谱, 与苯环相关的一系列CC双键伸缩振动特征谱以及与苯环相关的面内、面外变形振动特征谱均获得了明显增强。这种单一的大区域的拉曼散射基底,呈现出高低相间起伏分布的微观形貌,不同PS微球之间的空隙和深度有很明显的不同,能够显著改善表面Ag膜颗粒的大小和分布,进而提高了PS微球基底的SERS活性。该基底所具有的特殊阵列结构使其在利用SERS探究化学和生物等领域的单分子结构有很大的应用潜力。