La2/3Ca1/3MnO3/Eu2CuO4/La2/3Ca1/3MnO3磁性隧道结的制备与表征

采用磁控溅射，紫外线光刻和离子束刻蚀制备了La_2/3Ca_1/3MnO₃/Eu₂CuO₄/La_2/3Ca_1/3MnO₃磁性隧道结.通过对获得的磁性隧道结的I-V特性测量，发现非线性的I-V特性，显示结样品的隧穿特性.有趣的是发现在电极材料La_2/3Ca_1/3MnO₃的金属-绝缘体转变温度(Tp)以下，I-V曲线出现一个跳变.随着温度降低，开始出现跳变的临界电流增大，但是跳变都发生在同样的电压下～209mV.当电流增大或减小在跳变点附近出现回滞.这一跳变只发生在铁磁金属态，表明这是一个磁性相关联的效应，可能对应一种新的磁性开关过程.虽然，目前对这一现象背后的物理机理还不清楚，但是，这一现象有可能在未来自旋电子学器件方面具有潜在的应用价值. 关键词： 庞磁电阻 磁性隧道结 开关效应     

对靶溅射技术制备的La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜中Tc的降低

本文用对靶溅射技术制备了La2/3Ca1/3MnO3/YBa2Cu4O8/La2/3Ca1/3MnO3薄膜.与YBCO单层薄膜相比,由于超导/铁磁系统中的磁性邻近效应,三层薄膜表现出较低的超导转变温度.薄膜的R～T测量曲线显示出超磁阻(CMR)效应和超导转变,预示着超导和铁磁特性共存于LCMO/YBCO/LCMO三文治结构.     

成分调制的La1-xSrx MnO3复合隧道结

利用磁控溅射和Sr成分的调制以及原位热处理方法,在10mm×10mm大小的(001)取向SrTiO3单晶衬底上制备出三明治结构为La0.7Sr0.3MnO3(100nm)/La0.96Sr0.04MnO3(5nm)/La0.7Sr0.3MnO3(100nm)的隧道结外延薄膜,然后再次利用磁控溅射方法,在三层单晶膜上方继续沉积Ir22Mn78(15nm)/Ni79Fe21(5nm)/Pt(20nm)等金属三层膜.最后利用深紫外曝光和Ar离子束刻蚀等微加工技术,制备出长短轴分别为12和6μm或者8和4μm大小的椭圆形La1-xSrxMnO3成分调制的复合磁性隧道结.在4.2K和外加磁场8 T的测试下,La1-xSrxMnO3成分调制的复合磁性隧道结其隧穿磁电阻(TMR)比值达到3270%,直接从实验上证实了铁磁性La07Sr0.3MnO3金属氧化物的自旋极化率(97%)可接近100%,具有很好的半金属性质.     

La2/3 Ca1/3 MnO3中绝缘体-金属相变与CMR效应

我们研究了超大磁阻材料La2/3Ca1/3MnO3的磁电特性,发现由电阻测量得到的绝缘体－金属相变与由磁化曲线得到的顺磁－铁磁相变温区完全一致,均随磁场的增强推向高温区。结果证明绝缘体－金属相变起因于磁序的变化,并伴随着越大磁电阻效应的CMR的发生。     

La2/3Ca1/3Mn1-xCuxO3(x=4%)中的热弛豫现象

采用溶胶-凝胶法并经不同温度烧结而制备了名义组分为La2/3Ca1/3MnO3和La2/3Ca1/3Mn1-xCuxO3(x=4%)的系列样品,对它们进行了阻温关系测量.从试验结果观察到:在La2/3Ca1/3MnO3样品中,降温和升温测量的阻温曲线几乎完全重合,没有观察到明显的热弛豫现象.而在不同温度烧结的La2/3Ca1/3Mn1-xCuxO3(x=4%)样品中,阻温关系有明显的热弛豫现象.同时试验还观察到该热弛豫现象随样品烧结温度(颗粒尺寸)的增加逐渐消失.     

La0.67Ca0.33MnO3多晶薄膜电流效应

研究了在不同电流下多晶La0.67Ca0.33MnO3薄膜的电输运特性.观察到电阻随着电流的增大而减小,在多晶样品中当外加电流为1mA时负的电电阻(ER)即达到30%.同时,电流对于磁阻(MR)也有影响.考虑多晶样品中晶界的作用,我们提出了极化电流传输模型,对所观察到的实验现象进行了解释.     

La2/3Ca1/3MnO3体系La位上Y掺杂及其对输运性质的影响

零场下(La1-xYx)2/3Ca1/3MnO3(0相似文献   

(La0.7Sr0.3MnO3)m(BiFeO3)n超晶格间隔的La0.7Sr0.3MnO3三明治结构制备及表征

采用射频磁控溅射的方法在SrTiO3(001,基片上制备了(La0.7Sr0.3MnO3)m(BiFeO3)n超晶格间隔的La0.7Sr0.3MnO3三明治结构.X射线衍射分析证明(La0.7Sr0.3MnO3)m(BiFeO3)n具有明显的超晶格结构.电流垂直于薄膜表面测得的电阻-温度关系表明.La0.7Sr0.3MnO3)m(BiFeO3)n超晶格薄膜在290 K有金属-绝缘体转变,略低于单层La0.7Sr0.3MnO3薄膜的转变温度.电流在0.01-10 mA范围内,观察到薄膜的峰值电阻随电流增大而减小,峰值变化率远大于单层La0.7Sr0.3MnO3薄膜,且随着超晶格周期厚度的增加而增大.低温下,电流-电压曲线表明其导电机制应主要为空间载子限制,且显示较大的电压偏置,表现出肖特基结的特性.     

La0.67Ca0.33MnO3薄膜中的各向异性应变与电荷有序

本文采用脉冲激光沉积法在NdGaO3(001)单晶衬底上制备了一系列的La0.67Ca0.33MnO3薄膜,实验主要研究了薄膜的输运性质.La0.67Ca0.33sMnO3块材是铁磁金属基态,而La0.67Ca0.33MnO3/NdGaO3(001)薄膜由于各向异性应变的存在,可以观测到电荷有序绝缘相的出现.薄膜样品表...     

La2/3Ca1/3MnO3薄膜的光致电阻率变化特性

射频磁控溅射法制备了La2/3Ca1/3MnO3纳米薄膜(LCMO).该薄膜发生FM-PM相变的转变点温度为Tc≈308K(近似为电阻峰值温度Tp);在不同温度下的光电导性质实验表明所制备的LCMO薄膜在连续激光作用时低温段(TTc时,ΔR/R＜0,即光电导效应.调制激光脉冲光响应实验发现,光致信号强度和温度及偏置电流之间存在非线性关系:光致电阻率增大信号极大值为偏置电流的二次函数,而极大值对应的温度和偏置电流成线性关系,同时,光响应有一个截止温度,并且存在最佳光响应偏置电流和温度条件.分析认为LCMO薄膜的光致电阻率变化特性和材料的eg↓自旋电子的状态以及与此相应的小极化子的形成有关.     

Thermoelectric properties of Bi2Se3/Bi2Te3/Bi2Se3 and Sb2Te3/Bi2Te3/Sb2Te3 quantum well systems

In this work, we develop a theory of thermoelectric transport properties in two-dimensional semiconducting quantum well structures. Calculations are performed for n-type 0.1 wt.% CuBr-doped Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ and p-type 3 wt.% Te-doped Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ quantum well systems in the temperature range 50–600 K. It is found that reducing the well thickness has a pronounced effect on enhancing the thermoelectric figure of merit (ZT). For the n-type Bi₂Se₃/Bi₂Te₃/Bi₂Se₃ with 7 nm well width, the maximum value of ZT is estimated to be 0.97 at 350 K and for the p-type Sb₂Te₃/Bi₂Te₃/Sb₂Te₃ with well width 10 nm the highest value of the ZT is found to be 1.945 at 440 K. An explanation is provided for the resulting higher ZT value of the p-type system compared to the n-type system.     

Physical properties of BaMg1/3Nb2/3O3-BaCo1/3Nb2/3O3 solid solutions

Structural, electric and magnetic properties of Ba₃Mg_1−xCo_xNb₂O₉ based dielectric ceramic compounds have been studied. The samples, prepared by a solid state reaction method, were characterised by X-ray powder diffraction (XRPD), electron microscopy (SEM), dielectric (ε(T)) and magnetic measurements (χ⁻¹(T)). The XRPD analyses showed that the crystal structure of these compounds does change by the increase of substitution degree, passing from a superstructure hexagonal-type, (no. 164), space group (SG) to a simple structure cubic-type, (no. 221), SG. However, the evolution of the elementary unit cell lattice parameter can be followed and it exhibit a linear increasing tendency with increase in the substitution, indicating the existence of a solid solution through out the investigated range of substitution (0-1). The microstructure analysis shows a variation in the grain size and also the porosity of the samples with the degree of substitution. The results are in good agreement with that of dielectric measurements, which also showed that the dielectric constant (ε) increases with the increase of cobalt content. The magnetic characterization of cobalt substituted samples showed an antiferromagnetic type super-exchange interaction between these magnetic ions. At the same time, the values of effective magnetic momentum (μ_eff) are close to the value that corresponds to Co²⁺ free ions. The study highlights the possibility of modelling these materials by substitutions, in order to improve properties of negative-positive-zero (NPO) type dielectric applications.     

Giant dielectric relaxation in SrTiO3-SrMg1/3Nb2/3O3 and SrTiO3-SrSc1/2Ta1/2O3 solid solutions

Ceramic samples of (1−x)SrTiO₃-xSrMg_1/3Nb_2/3O₃ and (1−x)SrTiO₃-xSrSc_1/2Ta_1/2O₃ were prepared, and their dielectric properties were studied at x=0.005–0.15 and 0.01–0.1, respectively, at frequencies 10 Hz–1 MHz and at temperatures 4.2–350 K. A giant dielectric relaxation was observed in the temperature range 150–300 K, and not so strong but well-developed relaxation was found in the temperature range 20–90 K. The activation energy U and the relaxation time τ₀ were determined to be 0.21–0.3 eV and from 10⁻¹¹ to 10⁻¹² s for the high-temperature relaxation and 0.01–0.02 eV and 10⁻⁸–10⁻¹⁰ s for the low-temperature relaxation, respectively. The additional local charge compensation of the heterovalent impurities Mg²⁺ and Nb⁵⁺ (or Sc³⁺ and Ta⁵⁺) by free charge carriers or the host ion vacancies is suggested to be the underlying physical mechanism of the relaxation phenomena. On the basis of this mechanism, the Maxwell-Wagner model and the model of reorienting dipole centers Mg²⁺ (or Sc³⁺) associated with the oxygen vacancy are proposed to explain the high-temperature relaxation with some arguments in favor of the latter model. The polaron-like model with the Nb⁵⁺-Ti³⁺ center is suggested as the origin of the low-temperature relaxation. The reasons for the absence of ferroelectric phase transitions in the solid solutions under study are also discussed. From Fizika Tverdogo Tela, Vol. 44, No. 11, 2002, pp. 1948–1957. Original English Text Copyright ? 2002 by Lemanov, Sotnikov, Smirnova, Weihnacht. This article was submitted by the authors in English.     

全谱火焰光度法检测硫、磷、氮、砷、氯元素

火焰光度分析技术是一种能够快速灵敏检测硫、磷等元素的成熟方法。在环境检测,农残检测,工农业生产领域得到广泛应用。通过对传统火焰光度检测器的改进设计,采用光栅和CCD传感器阵列作为检测器的光电转换器件,拓展了检测化合物的种类,成功实现了对H2S,PH3,NH3,AsH3,Cl2为代表的硫、磷、氮、砷、氯五种元素的实时检测。由原来依靠特征波长检测拓展到利用物质火焰光度光谱信息进行定性定量分析。结合化学计量学的方法有望成为一种能够同时检测多类有毒有害气体的快速现场检测技术。     

La0.67Ca0.33MnO3薄膜皮秒光电效应

在1064 nm波长脉冲激光（脉宽25 ps）的照射下，钙钛矿氧化物薄膜La0.67Ca0.33MnO3/SrTiO3具有超快光电效应，对激光脉冲显示ps量级的响应时间，上升沿响应时间300 ps，半高宽700 ps，同时，对激光能量的响应灵敏度为500 mV/mJ。     

Luminescence properties of K1/2Bi1/2TiO3:Pr3+ and Na1/2Bi1/2TiO3:Pr3+

The luminescence properties of K(1/2)Bi(1/2)TiO(3):Pr(3+) and Na(1/2)Bi(1/2)TiO(3):Pr(3+) powders are investigated in the temperature range 10-600 K. The experimental data are interpreted on the basis of metal-to-metal charge transfer processes and by considering Bi(3+)-to-Pr(3+) sensitization effects.     

Fluoride glasses in the InF3-GaF3-YF3-PbF2-CaF2-ZnF2 system

New glasses have been synthesized in a multicomponent system based on indium fluoride. Samples of a few mm in thickness were obtained. They are transparent and homogeneous. Main physical properties such as density, characteristic temperatures, density, thermal expansion and refractive index have been measured. The evolution versus composition is reported for samples with the formula: (35−x) InF₃-xGaF₃-10YF₃-25PbF₂-15CaF₂-15ZnF₂. T_g lies between 260 and 296 °C while melting starts around 480 °C. Glass samples are stable at room temperature. By comparison with other standard fluoride glasses, they exhibit higher refractive index and density.     

E-T phase diagrams of a solid solution of the multicomponent PbZn1/3Nb2/3O3-PbMg1/3Nb2/3O3-PbNi1/3Nb2/3O3-PbTiO3 system near the morphotropic phase boundary

The specific features of the dielectric and pyroelectric responses of a solid solution in the barium-doped multicomponent yPbZn_1/3Nb_2/3O₃-mPbMg_1/3Nb_2/3O₃-nPbNi_1/3Nb_2/3O₃-xPbTiO₃ system of the composition y = 0.0982, m = 0.4541, n = 0.1477, and x = 0.3 near the morphotropic phase boundary have been investigated. It has been assumed that the maxima revealed in the dependences of the reversible permittivity on the electric field strength with both the forward and backward changes in the field (E ₌) are associated with the induced phase transition. Based on the experimental results, the E-T phase diagrams are constructed in the temperature range from ?100 to 150°C for different temperature-field regimes: (i) variation in the electric field E ₌ at a fixed temperature of the sample and (ii) variation in the temperature of the sample at a constant value of E ₌. It has been found that there is a singular point in the E-T phase diagram and that, in the vicinity of this point, the dielectric and pyroelectric responses of the studied ceramics exhibit specific features.     

Glass formation in the As2Se3-As2Te3-Sb2Te3 system

Chalcogenide glasses from the As₂Se₃-As₂Te₃-Sb₂Te₃ system were synthesized for the first time. The glass-forming region was determined by X-ray diffraction and electron microscopic analyses.The basic physicochemical parameters such as density (d), microhardness (HV) and temperatures of phase transformations (glass transition T_g, crystallization T_cr and melting T_m) were measured. Compactness and some thermomechanical characteristics such as volume (V_h) and formation energy (E_h) of micro-voids in the glassy network as well as the elasticity module (E) were calculated. The glass-forming ability was evaluated according to Hruby's criteria (K_G). The correlation between composition and properties of the (As₂Se₃)_x(As₂Te₃)_y(Sb₂Te₃)_z glasses was established and comprehensively discussed.