电子束蒸发沉积六硼化镧薄膜的逸出功(英文)

六硼化镧(LaB6)具有电子逸出功低、高熔点和高化学稳定性等优点,是制作热阴极和场发射阴极的理想发射体材料。而且在常规场发射尖锥表面涂敷一层LaB6薄膜能够大幅度提高场发射尖锥的发射能力。为了测量LaB6薄膜的逸出功,采用电子束蒸发技术沉积LaB6薄膜,并对薄膜进行了X射线衍射分析和X射线光电谱分析。通过测量薄膜的热电子发射特性和敷LaB6薄膜的硅尖锥阵列的场致电子发射特性确定了LaB6薄膜的逸出功,与块状LaB6多晶材料的逸出功大体相同,说明电子束蒸发沉积技术适合于制备高纯度、低逸出功的LaB6薄膜。     

六硼化镧薄膜场致发射的特性

阵列薄膜是在制备好的尖锥阵列上沉积其他材料的薄膜,以提高场发射阴极性能,它是一种有效的提高场发射阴极性能的方法。在n型硅片上先后采用氧化、光刻、干法刻蚀、氧化削尖等工艺,制备出曲率半径很小的硅尖锥场发射阵列,硅阵列中每个硅尖锥的底半径约2μm,锥高约1.04μm,每个硅尖之间间隔6μm,尖端的曲率半径约50nm,锥角约56°,尖锥阵列的密度约106/cm2。为了降低硅尖锥的功函数及提高抗离子轰击能力,通过电子束蒸发在硅尖阵列上沉积六硼化镧(LaB6)薄膜,薄膜的厚度大约50nm,锥尖曲率半径变为约111nm。X射线衍射(XRD)分析结果表明,电子束沉积在硅尖端的LaB6具有良好的结晶特性。硅尖锥及不同的真空度下阵列薄膜的场致发射I-V特性及电流发射稳定性的测试结果表明:沉积LaB6的薄膜阴极阵列的总发射电流达到125μA,是纯硅尖锥阵列125倍。并且硅阵列六硼化镧薄膜具有良好的场发射稳定性,是一种理想的薄膜场发射阵列。     

温度条件对反应电子束蒸发制备TiO2薄膜结构和性能的影响

研究基片温度(120～300 ℃)和热处理温度(400℃)对电子束蒸发TiO₂薄膜的结构和光学性能的影响.XRD分析表明,在120 ℃, 200 ℃和300 ℃的普通玻璃基片上采用电子枪加热蒸发制备的TiO₂薄膜具有非晶态结构,沉积态薄膜经过400 ℃保温1 h的热处理后得到的相为具有(004)取向的锐钛矿相,晶粒大小在3.6～8.1 nm之间.透射谱分析表明,薄膜的折射率随着基片温度的升高而增加;热处理后,薄膜的折射率也相应提高,其原因来自于薄膜的晶化.     

基底显微结构对薄膜生长影响的Monte Carlo模拟研究

利用Monte Carlo方法研究了基底显微结构对薄膜生长的影响. 对不同显微结构基底上薄膜生长的初始阶段岛的形貌和尺寸与薄膜覆盖度和入射粒子沉积速率之间的关系进行了模拟和分析. 模型中考虑了粒子沉积、吸附粒子扩散和蒸发等过程. 结果表明,基底显微结构对薄膜生长具有明显影响. 当沉积温度为300K、沉积速率为0.005ML/s（Monolayer/second,简称ML/s）、覆盖度为0.05ML时,四方基底上薄膜生长呈现凝聚生长. 随着覆盖度增加,岛的尺寸变大,岛的数目减少. 而对于六方基底,当覆盖度从0.05ML变化到0.25ML时,薄膜生长经历了一个从分散生长过渡到分形生长的过程. 无论是四方还是六方基底,随着沉积速率的增加,岛的形貌由少数聚集型岛核分布状态向众多各自独立的离散型岛核分布状态过渡.     

沉积工艺对二氧化锆薄膜生长特性影响的研究

利用反应离子束溅射、反应磁控溅射和电子束蒸发在K9基底上沉积ZrO2薄膜，并用原子力显微镜对薄膜表面形貌进行测量。通过数值相关运算，对不同工艺条件下薄膜生长界面进行定量描述，得到了薄膜表面的粗糙度指数、横向相关长度、标准偏差粗糙度等参量。由于沉积条件的不同，薄膜生长具有不同的动力学过程。在反应离子束溅射和反应磁控溅射沉积薄膜过程中，薄膜生长动力学行为均可用Kuramoto-Sivashinsky方程来描述，电子束蒸发制备薄膜的过程可以用Mullins扩散模型来描述，并发现在沉积薄膜过程中基底温度和沉积过程的稳定性对薄膜表面特征影响很大。     

基底温度对电子束蒸发制备氧化铝薄膜的影响

为了考察基底温度对氧化铝薄膜折射率以及沉积厚度的影响情况,在不同基底温度环境下,通过离子辅助电子束蒸发方式,在玻璃基底上制备了同一Tooling因子条件下所监测到相同厚度的Al2O3薄膜,利用分光光度计测量光谱透过率,依据光学薄膜相关理论,计算了基底温度在25℃～300℃范围内获得的膜层实际物理厚度为275.611 nm～348.447 nm,以及膜层折射率的变化。通过对实验结果的数值计算和曲线模拟,给出了基底温度对于薄膜的折射率和实际厚度的影响情况。     

新型的覆纳米粒子薄膜阴极的研究

采用直流磁控溅射的方法制备出Ir金属纳米粒子薄膜.利用扫描电子显微镜分析了纳米粒子的形态和分布以及不同工艺条件对粒子粒径及形貌的影响,表明纳米粒子的大小可通过调节溅射气体压强来控制.在25%孔度的W海绵基体内浸入6∶1∶2铝酸盐发射物质,然后在其表面沉积上厚度为200—500 nm的纳米粒子薄膜层,最后在H₂气中1200℃烧结,即制成了新型纳米粒子薄膜阴极.利用阴极发射微观均匀性测试仪对纳米粒子薄膜阴极和传统覆膜阴极的热电子发射的均匀性进行了对比研究.采用飞行时间质谱仪测试了真空本底、纳米粒子薄膜阴极、传统覆膜阴极等各种阴极蒸发物的成分,研究了阴极蒸发速率与阴极温度的关系,比较了不同阴极蒸发速率的大小.研究了Ba-W阴极覆上纳米粒子薄膜后的发射特性. 关键词： 纳米粒子薄膜 热阴极 发射均匀性 蒸发     

蒸发条件对碘化铅多晶薄膜结构的影响

采用真空蒸发法在普通玻璃上制备了PbI₂多晶薄膜.研究了蒸发速率、蒸发源与衬底距离、薄膜厚度以及衬底温度等实验条件对所制备PbI₂多晶薄膜结构的影响.利用X射线衍射仪和扫描电子显微镜对样品进行了测试.结果表明，在衬底温度为室温时得到(001)择优取向的多晶PbI₂薄膜，即沿c轴垂直衬底方向取向生长的薄膜.当衬底温度升高时，薄膜的择优取向逐渐由(001)转向(003)，且晶体颗粒变大.薄膜中的内应力随衬底温度的升高而降低.     

电子束蒸发制备HfO2高k薄膜的结构特性

使用高真空电子束蒸发在p型Si（100）衬底上制备了高k HfO2薄膜.俄歇电子能谱证实薄膜组分符合化学配比；x射线衍射测量表明刚沉积的薄膜是近非晶的，高温退火后发生部分晶化；原子力显微镜和扫描电子显微镜检测显示在高温退火前后薄膜均具有相当平整的表面，表明薄膜具有优良的热稳定性；椭偏测得在600?nm处薄膜折射率为2.09；电容电压测试得到的薄膜介电常数为19.这些特性表明高真空电子束蒸发是一种很有希望的制备作为栅介质的HfO2薄膜的方法. 关键词： 高k薄膜 HfO2 电子束蒸发     

电子束蒸发制备HfO_2高k薄膜的结构特性

使用高真空电子束蒸发在p型Si(1 0 0 )衬底上制备了高kHfO2 薄膜 .俄歇电子能谱证实薄膜组分符合化学配比 ;x射线衍射测量表明刚沉积的薄膜是近非晶的 ,高温退火后发生部分晶化 ;原子力显微镜和扫描电子显微镜检测显示在高温退火前后薄膜均具有相当平整的表面 ,表明薄膜具有优良的热稳定性 ;椭偏测得在 6 0 0nm处薄膜折射率为 2 0 9;电容 电压测试得到的薄膜介电常数为 1 9.这些特性表明高真空电子束蒸发是一种很有希望的制备作为栅介质的HfO2 薄膜的方法     

Enhanced field emission from LaB6 thin films with nanoprotrusions grown by pulsed laser deposition on Zr foil

Lanthanum hexaboride (LaB₆) films have been deposited on a zirconium foil by pulsed laser deposition method. The field emission studies of the LaB₆ deposited film have been performed in the planar diode configuration under ultra high vacuum conditions. The Fowler-Nordheim plots were found to be linear in accordance with the quantum mechanical tunneling phenomenon. A typical field emission current of 7.02 μA was drawn at an applied electric field of 2 V/μm. The field enhancement factor is calculated to be 8913 cm⁻¹, indicating that the field emission is from nanoscale protrusions present on the emitter surface. The atomic force microscope (AFM) investigation of the surface clearly shows the conical shaped nanoprotrusions of few hundred nanometers with asperities of 20-40 nm on its top. The emission current-time plot recorded at the pre-set value of emission current of 5 μA over a period of more than 3 h exhibits an initial increase and subsequent stabilization of the current. The results reveal that the LaB₆/Zr field emitter obtained by the pulsed laser deposition (PLD) is a promising cathode material for practical applications in field emission-based devices.     

Enhanced fatigue property of PZT thin films using LaNiO3 thin layer as bottom electrode

A highly (100)-oriented metallic LaNiO₃ film was prepared directly on a Si substrate by a simple metalorganic decomposition (MOD) technique using lanthanum nitrate and nickel acetate as the starting sources. Subsequent Pb(Zr,Ti)O₃ (PZT) thin films deposited on the LaNiO₃-coated Si substrate were obtained by a modified sol–gel method. It was found that the PZT thin films began to form a single perovskite phase at a low annealing temperature of 530 °C, and exhibited highly (100) orientation. A ferroelectric capacitor of Pt/Pb(Zr,Ti)O₃/LaNiO₃/Si annealed at 600 °C displayed a good P-E hysteresis characteristic and was fatigue-free even after 10¹¹ switching cycles. Received: 25 May 2000 / Accepted: 9 August 2000 / Published online: 30 November 2000     

Texture control and its impact on the properties of SrBi2Ta2O9 thin films prepared by pulsed laser deposition

SrBi₂Ta₂O₉ (SBT) ferroelectric thin films with different preferred orientations were deposited by pulsed laser deposition (PLD). Several methods have been developed to control the preferred orientation of SBT thin films. For SBT films deposited directly on Pt/TiO₂/SiO₂/Si substrates and in situ crystallized at the deposition temperature, the substrate temperature has a significant impact on the orientation and the remnant polarization (Pr) of the films; a higher substrate temperature benefits the formation of (115) texture and larger grain size. The films deposited on Pt/TiO₂/SiO₂/Si substrates at 830 °C are (115)-oriented and exhibit 2Pr of 6 μC/cm². (115)- and (200)-predominant films can be formed by using a La_0.85Sr_0.15CoO₃ (LSCO) buffer layer or by annealing amorphous SBT films deposited on Pt/TiO₂/SiO₂/Si substrates at 450 °C using rapid thermal annealing (RTA). These films exhibit good electric properties; 2Pr of the films are up to 12 μC/cm² and 17 μC/cm², respectively. The much larger 2Pr of the films deposited on the LSCO buffer layer and of the films obtained by RTA than 2Pr of the films deposited on Pt/TiO₂/SiO₂/Si substrates at 830 °C is attributed to a stronger (200) texture. Received: 30 January 2001 / Accepted: 30 May 2001 / Published online: 25 July 2001     

Pulsed laser deposition of Pb(Zr0.52Ti0.48)O3 thin film on cobalt ferrite nano-seed layered Pt(111)/Si substrate: effect of oxygen pressure

The effect of oxygen pressure during pulsed laser deposition of Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films on CoFe₂O₄ nano-seed layered Pt(111)/Si substrate was investigated. The PZT film deposited at oxygen pressure lower than 25 mTorr is identified as both perovskite and pyrochlore phases and the films deposited at high oxygen pressure (50-100 mTorr) show the single-phase perovskite PZT that has a perfect (111)-orientation. In addition, the film deposited at P_O2 of 50 mTorr has a uniform surface morphology, whereas the film deposited at P_O2 of 100 mTorr has a non-uniform surface morphology and more incompacted columnar cross-section microstructure. The polarization of film deposited at 100 mTorr is higher than that deposited at 50 mTorr, but shift of the hysteresis loop along the electrical field axis in the film deposited at P_O2 of 100 mTorr is larger than that of the film deposited at P_O2 of 50 mTorr.     

Effects of different deposition conditions on the properties of Cu2S thin films

Cu₂S thin films deposited on glass substrate by chemical bath deposition were studied at different deposition temperatures and times. The results of X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive X-ray analysis (EDX), the Hall Effect measurement system and UV-Vis absorption spectroscopy indicate that both deposition temperature and time are important to obtain polycrystalline thin films. XRD showed that the polycrystalline Cu₂S thin films have monoclinic structure. Meanwhile, the structural variations were analyzed using SEM. EDX analysis results of the thin film showed that the atomic ratio of Cu/S was close to 2:1. It was found from the Hall Effect measurement that the resistivity varied from 4.59?×?10^?3 to 13.8?×?10^?3 (Ω?cm). The mobility values of the Cu₂S thin films having p-type conductivity varied from 15.16 to 134.6?cm²/V.s. The dark electrical resistivity measurements were studied at temperatures in the range 303–423?K. The electrical activation energies of Cu₂S thin films were calculated by using Arrhenius plots, from which two different activation energy values are estimated for each thin film. Using UV-Vis absorption spectroscopy (Ultraviolet/visible), the direct and indirect allowed optical band gap values were determined to lie between 2.16 and 2.37?eV and 1.79 and 1.99?eV, respectively. In addition, the values of the refractive index (n) and the extinction coefficient (k) were determined.     

Synthesis and characterization of LaB6 thin films on tungsten, rhenium, silicon and other substrates and their investigations as?field emitters

The paper deals with the comparative study of nanocrystalline Lanthanum hexaboride (LaB₆) thin films grown on various substrates by Pulsed laser deposition and Arc plasma method. Field emission studies were carried out on LaB₆ films deposited on various substrates show metallic behavior of the emitters. The high value of field enhancement factors, indicating that the electron emission from LaB₆ nanoscale protrusions deposited on emitter surface. The post field emission surface morphology of the emitters showed no significant erosion of the films during continuous operation. The observed behavior indicates that it is linked with the growth of LaB₆ films on substrate crystal structure. The LaB₆ nanocrystallites/nanowires films were synthesized using arc plasma method shows good emission current stability. The LaB₆ micro/nanocrystallites were also obtained by picosecond laser irradiation which gives high enhancement β factor, and good emission current stability along with high current density. The results reveal that nanocrystalline LaB₆ films, exhibit high resistance to ion bombardment and excellent structural stability and are more promising emitters for practical applications in field emission based new generation devices.     

Effects of deposition temperature and post-annealing on structure and electrical properties in (La<Subscript>0.5</Subscript>Sr<Subscript>0.5</Subscript>)CoO<Subscript>3</Subscript> films grown on silicon substrate

(La_0.5Sr_0.5)CoO₃ (LSCO) thin films have been fabricated on silicon substrate by the pulsed laser deposition method. The effects of substrate temperature and post-annealing condition on the structural and electrical properties are investigated. The samples grown above 650°C are fully crystalline with perovskite structure. The film deposited at 700°C has columnar growth with electrical resistivity of about 1.99×10⁻³ Ω cm. The amorphous films grown at 500°C were post-annealed at different conditions. The sample post-annealed at 700°C and 10⁻⁴ Pa has similar microstructure with the sample in situ grown at 700°C and 25 Pa. However, the electrical resistivity of the post-annealed sample is one magnitude higher than that of the in situ grown sample because of the effect of oxygen vacancy. The temperature dependence of resistivity exhibits semiconductor-like character. It was found that post-annealing by rapid thermal process will result in film cracks due to the thermal stress. The results are referential for the applications of LSCO in microelectronic devices.     

Study on structural properties of epitaxial silicon films on annealed double layer porous silicon

In this paper, epitaxial silicon films were grown on annealed double layer porous silicon by LPCVD. The evolvement of the double layer porous silicon before and after thermal annealing was investigated by scanning electron microscope. X-ray diffraction and Raman spectroscopy were used to investigate the structural properties of the epitaxial silicon thin films grown at different temperature and different pressure. The results show that the surface of the low-porosity layer becomes smooth and there are just few silicon-bridges connecting the porous layer and the substrate wafer. The qualities of the epitaxial silicon thin films become better along with increasing deposition temperature. All of the Raman peaks of silicon films with different deposition pressure are situated at 521 cm⁻¹ under the deposition temperature of 1100 °C, and the Raman intensity of the silicon film deposited at 100 Pa is much closer to that of the monocrystalline silicon wafer. The epitaxial silicon films are all (4 0 0)-oriented and (4 0 0) peak of silicon film deposited at 100 Pa is more symmetric.     

Pulsed laser deposition of ZnO as conductive buffer layer of (001)-LiNbO3 thin films

1 (LO) mode peak at 579 cm^-1, indicating oxygen deficiency in the films. Significant dependence of the electrical property for the films on substrate temperature was shown. The I–V relation of the films exhibited non-ohmic behavior. Whereas the films deposited above 500 °C showed a metal-like property, at a lower substrate temperature semiconducting thin films were achieved. The (001)-oriented LiNbO₃/ZnO heterostructure was successfully prepared on quartz fused and (001) sapphire plates. Received: 6 April 1998/Accepted: 26 May 1998     

纳米TiO_2薄膜的低温等离子体制备技术

以四氯化钛为源物质,氩气为载气,氧气为反应气体,利用低温等离子体增强化学气相沉积在硅基表面制备出了TiO2薄膜。使用场发射扫描电子显微镜、X射线衍射仪等检测分析表征TiO2薄膜的性能与性质,并探讨了工艺条件如基片材料、沉积时间和基片温度对薄膜性能的影响。结果表明:制备的薄膜表面光滑均匀,结构致密,最小晶粒尺寸约15 nm;薄膜的晶型主要依赖于沉积温度,低于300℃沉积的薄膜是无定形的,300℃之上沉积的薄膜是锐钛矿结构。